Question about Cars & Trucks

1 Answer

Bosch classixx washer wont power up lights were on would not start,now no lights.

Machine was running a bit noisy,so had a look at the bearings applied sqirt of oil.tried to start up,light came on but would not start,tried to reset a few times,then all lights went off.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 887 Answers


You have a washer in your car? I'm confused.

Posted on Dec 01, 2012


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: 2005 Monte Carlo Change Oil Light Reset

Are 2 procedure to Reset the oil life.
1-- Using the accelator pedal.
Turn ignition ON with engine OFF
Fully press and release the accelerator pedal 3 times within 5 seconds.
The oil change light will flash a few times and them go OFF.
If the light is still on repeat the procedure.

2-- This procedure need the RADIO, if you have an aftermarket
Radio you don't be able to do.
Turn the ignition switch to ON position,
turn OFF the RADIO,
Press and hold the Tune disp, button for 5 seconds or until
Settings is displayed,
Press the seek ptype or seek pscan up and dow to scroll the main menu,
Scroll until the OIL LIFE appear on display
Press the 1prev or 2next to scroll the sub menu, RESET will be displayed , Press the TUNE disp buttom to reset,
A chime will be heard to verify the new settings and done
Will be displayed for one second.
Press the TUNE DISP to exit from the program,
A chime will be heard to verify the exit.

OK.. I hope this help on your question.
Thank you for use fixya.

Posted on Aug 23, 2008

  • 740 Answers

SOURCE: 2001 chevy silverado 4x4 abs dash light wont go off

Once the ABS light is on there is a problem with the ABS system. You can't really guess with this stuff. Also it becomes a safety issue when abs light is on the ABS system is in-operable. Here is my advice take your vehicle to any AUTO-ZONE store and they will check for FREE and let you know why this light is on it could be anything form abs sensors(wheel sensors) or something like that, they are four of them one in each wheel so make sure to get exact info as to what is the exact code and meaning. Good Luck feel free to contact t me if ou need more info

Posted on Dec 27, 2008

  • 239 Answers

SOURCE: 2002 Sebring wont start

sounds like fuses and relay problem

Posted on Jan 03, 2009

  • 71 Answers

SOURCE: 01 gmc sierra how to reset change engine oil light

Turn on the ignition switch without starting the vehicle and mash the accelerator to the floor 3 times slowly and this should reset the change oil sensor.

Posted on Jan 30, 2009

  • 170 Answers

SOURCE: Check engine light comes on and engine starts chugging.


Posted on Sep 01, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Squealing-power steering pump or belt tensioner bearing? squealing or whining when running and is worst when turning or accelerating. fluid level appears ok and no noticeable leaks

I have seen a couple noisy pumps on these vehicles. The fluid wears out after awhile and I have cured the noise before by simply draining and flushing with new fluid. You must use Chrysler ATF +4 transmission fluid for this, nothing else is suitable. This should work, if not, you'll need a new pump. Use a mechanics stethoscope to confirm the location of the noise, these trucks had problems with noisy alternator bearings as well.

Apr 15, 2011 | 2003 Jeep Liberty

1 Answer

Rearend whines when i accelerate.what is it?

most likely if it whines at light throttle but stops when u get off the gas the ring and pinoin gears are noisy, if it is noisy all the time it is the carrier bearings or the pinion gear bearing.

Apr 23, 2010 | 1990 Jeep Cherokee Limited

1 Answer

1968 MGC GT 4 speed with O/D Engine running, vehicle out of gear and with the foot off the clutch, there is quite a rumbling noise. Depress the clutch and the whole thing goes wonderfully quite? Is this...

It must be the first motion shaft bearing, the clutch thrust would be noisy and slow the tick over when you depress the clutch if it was faulty. If the car has ever been left standing the first motion shaft bearing can dry out and rust a bit then go noisy with use, does it growl in use?

Nov 08, 2009 | 2006 Triumph Tr 7

1 Answer

Loss of power on '92 Dakota>

Have you changed the fuel filter?

Sep 13, 2009 | 1992 Dodge Dakota

1 Answer

I have a 1999 Ford Ranger 2.5 L 4x2 and after i start the truck there is a slight hum and it gets louder when u speed up the rpms, it also gets really loud when i turn the steering wheel so i replaced the...

Ford Saginaw pumps are notoriously noisy power steering pumps. I have not had any that were not noisy. This is especially true when turning the steering wheel without the vehicle in motion.

It sounds like you may have a bearing race out of spec in your front hub assembly. Check for bearing play by pulling with your hands on each tire--if there is a clunking noise---replace the bearing.

Mar 26, 2009 | 1999 Ford Ranger SuperCab

2 Answers

2002 Sebring wont start

sounds like fuses and relay problem

Dec 30, 2008 | 2001 Chrysler Sebring

1 Answer

Engine noisy checked code and found knock sensor bad.

engine noisy,used one of them sunday mechanics code readers and reckon you know it all now ???only one cause of a noisy engine and thats because its been run with no oil,or had the guts thrashed out of it,or a pulley tensioner bearing run dry,clutch thrust bearing ,water pump,in fact anything .GET A PROFESSIONAL TO LISTEN,call a local mobile mechanic for an opinion then ask how to cure it on the cheap.

Nov 25, 2008 | 2002 Kia Rio

Not finding what you are looking for?

Open Questions:

0 Answers

My 2007 Dodge Ram 1500 4X4 with the 5.7 Hemi engine threw me for a loop yesterday. Stay with me on this as it gets weird. First the engine shut down as did the tach. Then started back up as I coasted down the road (in Mexico of all places). Next it did the same thing again but in addition the cruise would not work and the overdrive didn't work (usually @ 2000 RPM at 60 then the tach showed 2500 RPM. Sure enough by engaging the button on the shifter no change in RPM. Then the engine shuts down, tach inop, OD inop, cruise inop, and the check engine light comes on. Then (it gets better) all of the above happens and I coast to a stop. Shut the ignition off, turned it back on and the cruise works, the overdrive works but the engine shuts down BUT the tach is now working. Long story longer I limp back to Green Valley, AZ with the truck and run the codes and the only code is a P0300 (random cylinder misfires within a predetermined period of time (No S#@t). Also was able to determine the following codes. P0339 (crankshaft position sensor intermittent, P1128 Closed loopfueling not achieved-bank 1 as well as P1129 (the other bank). I'm leaning towards replacing the ECM. Could it possibly be the IPCM (integrated power control module)? OR do I have a loose connection somewhere? It seems the problem gets worse when I go over rough roads (about all of Mexico is ROUGH roads. LOL) Call me "Looking for answers before I pull the rest of my hair out".

May 26, 2018 | Dodge Cars & Trucks

Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13735 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides