Question about 2005 Chevrolet TrailBlazer LS

Open Question

Lower ball joint 2005 chevy trailblazer

How do you replace front lower ball joints

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: lower ball joint removal how to

  1. Remove the steering knuckle with wheel hub and bearing attached.
  2. Remove the lower ball joint flange with a chisel.
  3. Install J9519-E and J34874 to the lower ball joint.
  4. Remove the lower ball joint from the lower control arm using J9519-E and J34874


  1. Install the lower ball joint and J9519-E, J41435, and J45105-2 to the lower control arm.
  2. Install the lower ball joint to the lower control arm using J9519-E, J41435, and J45105-2.
  3. Remove J9519-E, J41435, and J45105-2 from the lower control arm
    1. Install J9519-E and J45105-1 to the lower ball joint.
    2. Flare the lower ball joint flange using J9519-E and J45105-1.
    3. Remove J9519-E and J45105-1 from the lower ball joint.
    4. Install the steering knuckle with wheel hub and bearing attached. Install the tire and wheel.
    1. Lower the vehicle.
    2. Check the front wheel alignment.
these jouints are pressed in and there is a flange that is flared this is what the tool numbers refer too.

Posted on Sep 12, 2008

  • 94 Answers

SOURCE: repalce ball joints 01' Chevy Blazer 4WD

you should just be able to loosen the half shaft and be ok that way

Posted on Mar 09, 2009

  • 2002 Answers

SOURCE: upper and lower ball joints

Jack the truck clear of the ground and let the wheel assembly hang. After you remove the tire place your jack under the lower control arm so it's firm. Remove the cotter pin, if you have one and loosen the big nut almost off. Wedge a "pickle fork" between the control arm and the spindle and give it a belt with a hammer until the ball joint pops. Raise the jack so you can undo the nut easily and separate the control arm and spindle.
The upper ball joint is riveted or bolted in. Grind the rivets or use a cold chisel and remove the ball joint. Clean up the area with some sandpaper, dirt , loose rust, etc.and put the new joint in. Put the spindle back on using the jack if necessary and put the nut back on and tighten.
The lower ball joint is pressed in. Tie the spindle out of the way and brace the lower control arm with some blocks or the jack if you have to. A few whacks with a hammer should pop the joint out. Clean the hole out lightly, just to remove loose rust and dirt. Put the ball joint, minus the grease fitting ,,in the hole and use the jack with a block of wood, to put it in place.You may have to fiddle with the spindle to make sure it is lined up. I've never had any trouble using a 1ton trolley jack and the weight of the truck to put the lower ball joint back in. Replace the nut and grease fitting.
The new ball joints will probably come with cotter pins, use them. Make sure the new joints are tight or they will wear the holes in the spindle. Don't forget to grease the new joints. Hope this helps.

Posted on Jul 14, 2009

  • 3600 Answers

SOURCE: how to remove lower ball joint 2001 chevy silverado 2500 hd 4x4

The reason is they are pressed in and you have to press them out with a tool and some have a C clip that has to be removed you can go to schucks or autozone to rent the tool to press out and it has to be pressed back in.

Posted on Jul 25, 2009

emissionwiz
  • 75797 Answers

SOURCE: replace lower ball joints on a 2000 chevy blazer 4

Raise vehicle up on jack stands so that the stands are under the lower controll arms and the suspension is "loaded" Remove the front tire(s) (if you break the torque on the nuts while the wheel is still on the ground it helps, but do not loosen them completely as you will be looking for new rims and wheel studs too). Place a drift or some other suitable object in one of the brake rotor vanes so that it will hit the brake caliper and stop the rotor from moving and remove the CV shaft nut (it's a big ****** make sure you have the right socket on hand before getting to this point). Next remove the brake caliper and rotor then undo the wheel bearing retaining bolts and remove the wheel bearing. This should give you enough room to move the axle shaft back and up so you can work on the ball joint. If you've had ball joints replaced before just unbolt the ones that are installed and using a pickle fork, or a block of wood and a hammer, drive the ball joint stud from the knuckle. (make sure to support the upper control arm so it doesn't drop down on you when you do this) If you are working on original ball joints then I reccomend placing a block of wood or something else that will protect the cv boots from drill bits ect and drill out the rivets holding the ball joint in place. then remove in the same manner indicated in the previous paragraph. installation is pretty much the reverse of removal and don't forget to torque your cv shaft nut I have a 1999 and the manual specs 103FTlbs... This is a critical torque as it helps preload your wheel bearing. Too high and you'll burn them up, too low and they'll be loose and wear out.

Posted on Oct 08, 2009

Testimonial: "Thank you for your directions this will help very much."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Latitude. How can I replace control arm and ball joint assembly?


Lower you can do fairly easy. Upper, a bit tougher.For the upper you will need a spring compressor.

Mar 21, 2016 | 2011 Jeep Patriot

1 Answer

How do you replace the lower ball joints on a 2000 windstar?


According to Autozone.com, you must replace the whole control arm. Here is their procedure:
NOTE do not begin the removal procedure unless a new strut-to-lower arm nut, a new ball joint pinch bolt/nut and a new lower arm-to-front subframe bolt/nut are available.

  1. Remove or disconnect the following:
    NOTE
    Do not use a hammer to separate the ball joint from the front wheel hub and spindle.



    WheelsLower arm strut nut and dished washer. Discard them.
  2. Place the steering wheel in the unlocked position.
    NOTE
    Do not allow the halfshaft to move outward. Over-extension of the halfshaft joint could result in separation of internal parts, causing failure of the halfshaft joint.
  3. Remove or disconnect the following:
    NOTE
    Use extreme care to not damage the ball joint boot seal.



    Lower arm ball joint nut and pinch bolt. Discard them.Lower arm from the front wheel knuckle



    Remove and discard the lower arm-to-front subframe bolt and nutRemove the lower arm from the vehicleTo install:
    1. Install or connect the following:

      Lower arm strut into the lower arm rear strut bushingLower arm into the front sub-frame bracketNew lower arm-to-front subframe nut and bolt. While holding the lower arm horizontal, tighten to 85-97 ft. lbs. (115-132 Nm).Ball joint stud-to-wheel hub and spindle, making sure that the ball stud groove is properly positioned.New lower arm ball joint pinch bolt and nut. Tighten to 46-52 ft. lbs. 62-71 Nm).
    2. Clean the lower arm strut threads to remove dirt and contamination.
    3. Install the dished washer with the dished side away from the lower arm rear strut bushing.
    4. Install the front suspension lower arm strut-to-strut nut and tighten to 85-97 ft. lbs. (115-142 Nm).
    5. Install the wheels.
    6. Lower the vehicle.

Jun 12, 2015 | Cars & Trucks

2 Answers

How to replace left front lower arm ball joint


replace left front lower arm ball joint Anon, Link shows how to replace lower ball joint it is a Lexus, pretty much identical to your lower suspension. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Replace Front Lower Ball Joint
http://z4.invisionfree.com/lexusaltezzaclub/ar/t9466.htm
Moog Balljoint amazon review Lexus IS300
2001 Toyota Altezza lower ball joint Google Search

Sep 22, 2013 | 2001 Toyota Altezza

1 Answer

How do i replce ball joints on a 99 pontiac sufire


Lower Control Arm Ball Joint Replacement Removal Procedure Tools Required J 43828 Ball Joint Separator
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Remove the stabilizer shaft link. Refer to Stabilizer Shaft Link Replacement .
  4. Remove the wiring harness from the lower control arm.

  5. 165249.gif
    tif.gif
  6. Remove the cotter pin (1) from the ball joint (3).
  7. Remove the nut (4) from the ball joint (3).

  8. 490085.gif
    tif.gif
    Notice: Use only the recommended tools for separating the ball joint from the knuckle. Failure to use the recommended tools may cause damage to the ball joint and seal.
  9. Remove the ball joint from the steering knuckle using the J 43828 .

  10. 491742.gif
    tif.gif
  11. Remove the lower control arm front (1) and rear (4) mounting bolts.
  12. Remove the lower control arm (1) from the vehicle and place in a vice.
  13. Drill out the 3 rivets (3) retaining the ball joint to the lower control arm (2).
  14. Use a 3 mm (1/8 in) drill bit in order to make a pilot hole through the rivets.
    Finish drilling the rivets with a 13 mm (½ in) drill bit.
  15. Remove the ball joint (4) from the control arm (2).
Installation Procedure

    165250.gif
    tif.gif
  1. Install the ball joint (4) into the control arm (2).
  2. Install the 3 ball joint bolts (3) and the nuts (1). Follow the instructions in the ball joint kit. Tighten the ball joint bolts (3) according to the specifications in the instructions.

  3. 491742.gif
    tif.gif
  4. Install the lower control arm (2) to the front suspension support (1)
  5. Notice: Refer to Fastener Notice in the Preface section.
  6. Install the lower control arm front (5) and rear (4) mounting bolts.
  7. Tighten • Tighten the front bolt to 107 N·m (79 lb ft). • Tighten the rear bolt to 110 N·m (81 lb ft).
    165249.gif
    tif.gif
  8. Install the lower ball joint stud (3) to the steering knuckle (2).
  9. Install the ball joint stud (3) through the steering knuckle (2).
  10. Install the ball joint nut (4).
  11. Tighten
    Tighten the ball joint nut to 55 N·m (41 lb ft) plus 180 degree rotation minimum-65 N·m (50 lb ft) plus 180 degree rotation maximum to install the cotter pin.
  12. Install the wiring harness to the lower control arm.
  13. Install the cotter pin (1).
  14. Install the stabilizer link to the lower control arm. Refer to Stabilizer Shaft Link Replacement .
  15. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  16. Inspect the front wheel alignment. Refer to Wheel Alignment Specifications in Wheel Alignment.

Sep 15, 2011 | 2003 Pontiac Sunfire

1 Answer

Need pictures and procedure 91 Ford pickup F250 twin I beam ball joint replacement.


Wheel Spindle, F-150, F-250, F-350
Removal
  1. Raise the front of the vehicle and install safety stands.
  1. Remove the wheel and tire assembly. Refer to Section 04-04 .
  1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
  1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
  1. Remove the rotor from the front wheel spindle (3105).





    Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
    (57-75 Lb-Ft) B - Tighten to 68-92 Nm
    (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)
  1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
  1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
  1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Remove the cotter pin and castellated nut from the lower ball joint stud.
  1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
  1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
    Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
  1. Remove the front wheel spindle and ball joint from the axle.






Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal
  1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
  1. NOTE: Lower ball joint must be removed first.

    Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
  1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
  1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
  2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
    Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.


    Installation
    1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.

      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.

      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
    1. Turn forcing screw clockwise until ball joint is seated.



    2. snorkelbobby_49.gif

Mar 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

How to replace a lower ball joint on a 1988 pontiac grand prix hit a pothole and it popped out


Hope this helps and please don't forget to rate! Thank you!


e8fbd9d.gif
Front ball joint with heat shield

Remove and Replace-

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the front wheel and tire assembly.
  4. Unfasten the retaining bolts, then remove the ball joint heat shield.
  5. Remove and discard the lower ball joint cotter pin.
  6. Remove the ball joint nut.
  7. Loosen, but do NOT remove, the stabilizer shaft bushing assembly bolts.
  8. Separate the ball joint from the strut/knuckle assembly using ball joint/tie rod puller J-35917 or equivalent.
Do NOT damage the halfshaft boots when drilling out the ball joint rivets.
  1. Drill out the rivets retaining the ball joint to the knuckle strut assembly and remove the ball joint from the knuckle. Use a 1/8 in. drill bit. Refer to the instructions in the ball joint replacement kit.
To install:
  1. Position the lower ball joint in the strut/knuckle assembly.
  2. Install the four ball joint bolts and nuts, as shown in the ball joint kit and tighten to specifications.
  3. Install the ball joint-to-lower control arm. Install a new ball joint-to-lower control arm nut.
  4. Tighten the stabilizer shaft bolts to 35 ft. lbs. (48 Nm).
  5. For 1988-91 vehicles, tighten the ball joint-to-lower control arm nut 15 ft. lbs. (20 Nm) plus at least an additional 90° (11/2flats), plus enough to align the cotter pin hole. Do NOT overtighten.
  6. For 1992-96 vehicles, tighten the lower ball joint nut to 63 ft. lbs. (85 Nm). Tighten to align the next slot in the nut with the cotter pin hole in the stud. Do NOT tighten more than 60° (1 flat) to align with the hole.
  7. Install a new cotter pin.
  8. Position the ball joint heat shield and secure with the retaining bolts. Tighten to 62 inch lbs. (7 Nm).
  9. Install the front wheel and tire assembly, then carefully lower the vehicle.
  10. Connect the negative battery cable and check for proper suspension operation

Apr 26, 2010 | 1988 Pontiac Grand Prix

1 Answer

Ball and socket joint on front left tire has come out


If it's the upper ball joint, just the ball joint can be replace, but if it's the lower ball joint the complete lower control arm will have to be replace, arm will come with new ball joint and bushings.

Jan 20, 2010 | 1998 Plymouth Breeze

1 Answer

How to change lower ball joints


part of lower arm assembly only.

Installation
  1. Inspect lower ball joint boots and seals for damage and replace if required. Lower ball joint and seal is part of front suspension lower arm and must be replaced as an assembly.
  1. NOTE: Do not tighten the front suspension lower arm bolts and nuts to the specified torque until the end of assembly. Install nuts and tighten until snug.

    Position the front suspension lower arm in the front crossmember. Install the bolts. Install the nuts and tighten until snug.
  1. Install torsion bar. Refer to Torsion Bar in this section.
  1. Raise the front suspension lower arm to allow installation of front suspension lower arm ball joint into spindle bore.
  1. Lower front suspension lower arm with a jack while making sure lower ball joint is seated in spindle bore. Install the lower ball joint attaching nut and tighten to 113-153 Nm (82-113 lb-ft). Install a new cotter pin.
  1. Raise vehicle. Position the front shock absorber and install the nut/washer/bushing assembly. Tighten nut to 40-55 Nm (30-40 lb-ft).
  1. Install the two nuts attaching the front shock absorber to the lower control arm and tighten to 21-29 Nm (15-21 lb-ft).
  1. NOTE: Front suspension lower arms must be in the horizontal or curb position (vehicle on the ground) when tightening the front stabilizer bar link bolts. Use jackstands to raise the front suspension lower arms to the horizontal position or lower the vehicle to the ground (curb position).

    Lower the vehicle to the ground.
  1. Connect the stabilizer bar link bolt to the front suspension lower arm and tighten to 13-17 Nm (10-13 lb-ft).
  1. Tighten nuts and front suspension lower arm bolts to the No. 1 crossmember to 150-200 Nm (111-148 lb-ft).
  1. Check ride height and align as necessary. Refer to Section 04-00 .
  1. Lower the vehicle.

Apr 17, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
2005 Chevrolet TrailBlazer LS Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...