Question about 2007 Renault Scenic 1.6

1 Answer

How can I dissasembly headlamp from body

I wonder whether I could replace by myself a worned policarbonate cristal headlamp housing, so I would need to take the complete assy off, but I hav'nt find out how is it fixed to body and I need - at least- where the holding screws are located and how to reach them.

Posted by on

  • Ricardo Mart?nez
    Ricardo Mart?nez Dec 01, 2012

    I'm terrible sorry for my english. Is more than changing bulbs is the whole headlight assembly y need to take out!!. Thanks anyway for tour time

  • Jonah Oneal Dec 02, 2012

    sorry meant remove plastic cover rear of headlight assembly.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Renault Master
  • 14,036 Answers

To replace headlight bulbs turn steering so you can open flap in the wheel arch.open flap liner to access of the rear headlight unit.to remove inner bulb in headlight housing remove the air intake duct at front of the air cleaner housing right hand side unclip the wiring harness connector unclip the the left wiring harness connector front of fuse and relay.to remove the dipped beam remove the plastic cover from rear of head light unit.through wheel flap opening. rotate bulbholder anti clockwise to remove bayonet fitting remove headlight bulb. WARNING WEAR CLEAN GLOVES WHEN HANDLING HEADLIGHT HALOGEN BULBS OILS FROM HANDS WILL CAUSE HALOGEN BULB TO OVERHEAT AND BLOW OUT.

Posted on Dec 01, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 03 Buick Rendezvous. The automatic lights never turn off until the car is turned off, chimes when left turn signal is on and a/c won't turn on? How do I fix this?


DTC B2577
The body control module (BCM) controls the headlamp relay by grounding the control circuit of the headlamp.
Diagnostic Aids
• If the DTC B2577 is a history DTC, the fault may be intermittent. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
• An intermittent short to ground or an open in the following locations may cause an intermittent malfunction to occur:
- The low beam headlamp relay control circuit
- The headlamp relay control circuit
- The headlamp relay
- The BCM

- The BCM
Step
Action
Yes
No
Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference: Master Electrical Component List
1
Did you perform the Diagnostic System Check?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Lighting Systems
2
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, command the HDLP low beam relay ON and OFF.
Does the HDLP low-beam relay turn ON and OFF with each command?
YES - Go to Diagnostic Aids
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the HDLP low beam relay.
Turn ON the ignition, with the engine OFF.
Probe the coil side supply circuit of the HDLP Low-beam relay with a test lamp that is connected to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 10
DTC B2578
DTC B2603
The body control module (BCM) controls the DRL relay by grounding the control circuit of the DRL relay coil.

DTC B2645
The body control module (BCM) uses the ambient light sensor signal in order to control the daytime running lamp system. The ambient light sensor is connected to the BCM through the signal circuit and the reference circuit of the ambient light sensor.
DTC B2647
--------------------------------------------------------------------------------
DTC B2648
DTC B2665
The headlamp switch provides a direct ground input into the body control module (BCM) for the headlamp switch input when the switch is activated. This input is used by the BCM in order to control the headlamps when the headlamp switch is in the HEAD position.
DTC B3857
The body control module (BCM) monitors the high beam headlamp signal circuit by verifying the high beam input.

Rather then going at this blindly an just replacing parts take it to a qualified repair .

Apr 30, 2017 | Cars & Trucks

1 Answer

How do you dissasemble the front headlight assembly to allow the bulbs to be changed


under the hood on both sides of the headlamp is a white tab that needs to be pulled up on both sides to allow the assembly to come out then just twist the bulb from behind and pull it out. it will have 2 tabs for each side headlamp assembly.

Dec 31, 2010 | 2001 Chevrolet Cavalier

1 Answer

Do I need to go to a body repair shop in order to replace a fender? I can purchase one online and wondered if I can install it?


can be done yourself , alignment on gm trucks is sometimes tricky and bolt holes may need to be reamed out to fit properly , front bumper and headlamp need to be rmoved also to replace the fender

Aug 24, 2010 | 1998 GMC Jimmy

1 Answer

Headlamps flicker when hitting bumps. Notice it more on right side. Lamp ground to body is good. Connector pins to lamp are good. Adjusted headlamps, changed bulb, still have problem. No flicker noticed...


yes i agree, what you have done is what i would have been telling you to check so well done for saving you and me time.first its either one of what you say but its my guiss the headlamp housing is loose after what you have all ready done i think you will find the culpuit quick,TIP,if you find the housing loose try using cable ties they work a treat without haveing to use screws ,any problems dont be afraid to come back to me,adrian,,,,,,,,

Aug 20, 2010 | 1999 Lincoln Town Car

1 Answer

How to change the headlight bulb on 2009 gmc sierra driver side


1. Loosen only, do not remove, the lower outside hidden headlamp bolt (2). 2. Depress the housing support tab with a flat-bladed tool downward in order to release the headlamp assembly from the support. 3. Pull the lamp assembly slightly forward to access the electrical connection. 4. Disconnect the forward lamp harness main electrical connector from the headlamp harness.
Headlamp Screws (Qty: 2)
1 Caution: Refer to Fastener Caution .
6 Nm (53 lb in)
O Headlamp Screw (Hidden)
6 Nm (53 lb in)
3 Headlamp Housing Support


Preliminary Procedure Remove Healamp
Remove either the LF or RF headlamp assembly. Refer to Headlamp Replacement (Chevrolet) Headlamp Replacement (GMC HD)
Headlamp Replacement (HD Diesel).
Headlamp Bulb (Hi)
Warning: Refer to Haiogen Bulb Warning .
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.
Headlamp Bulb (Lo)
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.

Need more come to https://www.autorepairhelp.us


change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-0.png change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-1.png

Aug 14, 2010 | 2008 GMC Sierra 2500HD 2WD

1 Answer

Headlights removal ford explorer 96


  1. Check that headlamp switch (11654) is in the off position.
  2. Lift hood (16612).
  3. Release latch and swing filler panel to left or right.
  4. Remove electrical connector from headlamp bulb by grasping wires firmly and snapping connector rearward.
  5. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding ring off plastic base. Keep headlamp bulb retainer as it may be used again to retain new headlamp bulb.
  6. Carefully remove headlamp bulb from socket by gently pulling straight backward out of socket. Do not rotate headlamp bulb during removal. 7056091.gif
Headlamp Assembly, Explorer
Removal and Installation
  1. Disconnect battery negative cable.
  2. Remove blind rivets (2) attaching screws (4) and radiator upper sight shield.
  3. Remove turn/park lamp attaching screws (2) and pull assembly away from body. Remove bulb sockets from housing and remove lamp assembly. Repeat on opposite side of vehicle.
  4. With turn/park lamp assembly removed, screw attaching grille to front fender flange is accessible. Remove grille attaching screw. Repeat on opposite side of vehicle.
  5. Remove attaching screws (4) located across top of grille.
  6. Grip lower edge of grille and pull outward to disengage from retaining clips. Remove grille.
  7. Using needle-nose pliers, compress barbs on headlamp housing retainer. With barbs compressed, pull forward on housing just enough to disengage from retainer. Repeat on opposite side of headlamp housing.
  8. Turn headlamp housing as necessary and pull forward to disengage from headlamp aiming ball socket.
  9. Disconnect wiring from headlamp bulb socket.
  10. If replacing headlamp housing, remove retaining collar and bulb.
For installation, follow removal procedures in reverse order. Make sure to check headlamp aim. 568a220.gif

Apr 02, 2010 | 1996 Ford Explorer

1 Answer

How do you replace the passenger side low beam on a Pontiac Grand Prix '07? I can't get to it from the back, so I'm wondering if there is a special tool to take off the front lens.


raise the hood. lift upward on the headlamp retainer(its a off white color tab right behind the lamp asm.in about the middle of lamp)pull the headlamp asm. outwardenough to release the headlamp asm from the upper fascia support.position the headlamp asm. away from the vehicle body to access the electrical connector. disconnect the electrical connector from headlamp asm.remove headlam asm. from vehicle. remove headlamp bulb /socket from the headlamp ,by turning counter clockwise. remove headlamp bulb/socket from the headlamp asm. install new bulb in socket and reverse procidure .

Feb 22, 2010 | 2007 Pontiac Grand Prix GXP Sedan

2 Answers

How do you remove outer lens


If you are referring to the headlamp, there is a procedure in the owner manual for replacing the bulb.
If you did not get an owners manual with your truck ( purchased used ), you can download one from Ford :
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

This is the procedure for the New Body style 2004 MY F-150
91c59f5.jpg

If you have a 2004 Heritage or Lightning model ( same body as the 97-03 MY F-150s ) this is the procedure
0ca8f25.jpg

If you are talking about removing the lens from the headlamp housing, this requires removing the set screws in the lamp housing, and heating the lamp up in the oven or with a heat gun. It can warp the unit if you heat it too much, this is just to get the sealant to release. Might be best buying a replacement lamp housing on one of the auction sites, or Ford F-150 sites if this is the case.

Jan 06, 2010 | 2004 Ford F150

1 Answer

How do you remove the head lamp assembly on a 1993


1. Make sure headlamp is off and open hood.
2. Taurus model years 1990-1999: you must remove the whole headlamp to replace the bulb. Not a horrible task. Just annoying.
3. Facing the driver's side headlamp, and looking at the headlamp itself, at clock positions 8, 11 and 1 are the headlight housing screws. They all look the same. Using a 10mm socket wrench, remove these 3 screws and set them aside.
4. Just to the right of the "11 o'clock" housing screw is a bolt (same hexagonal 10mm sized top as the housing screws). This just needs a few turns to loosen it.
5. Gently pull the whole headlight forward. Now you can get at the bulb.
6. Disconnect the electrical connector from the bulb. Now the headlamp is free to work with. Remove the bulb, replace with a new bulb, make sure the bulb housing cylinder is in place and reconnect the electical.
7. Place headlamp back into position. Line up screw holes. Tighten the bolt. Replace housing screws and tighten.
8. Passenger side headlamp is mirror image of driver's side. Screws at 11, 1 and 4 o'clock positions. Bolt should be to the left of the "1 o'clock" housing screw.

Oct 12, 2009 | 1993 Ford Taurus

1 Answer

Replace brakelight in trunk of 300m


REMOVAL
NOTE: Some moisture accumulation inside a vented headlamp unit is normal. Moisture will vent from tubes or vents located on the back of the unit. This normal condition will appear as a fogging on the inside of the headlamp lens (similar to the fog that sometimes appears on the inside of the windshield). This moisture may be removed by activating the headlamps on high beam for 15 minutes.

If water droplets larger than 1 mm in size have accumulated on the inside of the headlamp lens, the headlamp unit should be replaced.


CONCORDE/300M
Release hood latch and open hood.
Disconnect and isolate the battery negative remote cable.
Remove the one bolt retaining the washer bottle filler neck and move aside.
Remove the two bolts retaining the speed control servo and move aside.
Remove fasteners to upper radiator crossmember:
Two jack screws on each side.
Three crossmember retaining bolts on each side.
Three push pin fasteners across top of grille.
Gently pry back grille and remove the two bolts to front crossmember. This will allow you to move the crossmember forward, pivoting at the radiator grille, to access the headlamp unit.
NOTE: Once the crossmember is loose, take care not to scratch the fenders.

Maneuver the headlamp unit to remove from behind fascia. Gentle prying of fascia may be needed to clear it enough to remove the headlamp unit.
Disconnect the lamp connectors and transfer lamps if replacing unit.
INTREPID
Release hood latch and open hood.
Disconnect and isolate the battery negative cable.
Remove jackscrews attaching headlamp to body (Headlamp Housing – Intrepid).
Remove headlamp from body.
Disconnect wire connector from headlamp and parking, side marker, and turn signal lamps.
Remove headlamp housing from vehicle

Mar 26, 2009 | 2002 Chrysler 300M

Not finding what you are looking for?
2007 Renault Scenic 1.6 Logo

356 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

xxxxxx xxx

Level 3 Expert

4869 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...