Question about 2011 Suzuki Kizashi

Open Question

2011 suzuki kizashi headlight adjustment

The port to adjust left right is covered

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: Headlight adjustment

the screws for adjusting the headights are right next to the lights, they are phillips heads and are for adjusting the side to side, 
the adjusting screws for the up and down, are on the bottom of the headlights, and they are a small hole in the grill trim, these lights need a pretty long skinny screwdriver with a phillips head

Posted on Feb 12, 2009

Ad
  • 1986 Answers

SOURCE: headlight alignment

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: how do i adjust my

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 19, 2009

Testimonial: "thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I get our 2011 Suzuki Kizashi to accept a USB cable to enable our portable XM radio unit to work? It currently states: "Not Supported" each time a usb is hooked up to the portable XM unit. (On


I believe the USB socket your Subaru is only a charging port and does not really hook to the radio. This would require more than I know how to do, unless you can enable bluetooth on the car and your XM will work that way.

Dec 12, 2014 | 2011 Suzuki Kizashi

2 Answers

How do i replace head lamp on kizashi?


the bulb or the the whole housing/????????
read the manual at
$4

https://suzukipitstopplus.com/Products/10243-2011-kizashi-service-manual.aspx

the glove box.
open the door
extract the oper guide
turn to head light page, bingo?

Sep 02, 2014 | 2011 Suzuki Kizashi

2 Answers

How do u adjust headlghts on 1991 gmc seirre


adjustment is on the top of the light and the side.

Jun 22, 2014 | 2003 GMC Sonoma Extended Cab

1 Answer

How to remove external window trim on a kizashj rear door


this is covered in the FSM. get one
or log into alldata.com and see if the Body sections there covers this.
the FSM for sure does.

Mar 02, 2014 | 2011 Suzuki Kizashi

1 Answer

How do you change the low beam headlight on drivers side of suzuki kazahi


You need to remove the front bumper.
It is easy but tricky.
Once the bumper is off you need to remove all the plastic head lamp.
You'll see the light bulbs once you remove a round rubber cover in the back of the plastic head lamp.

Oct 24, 2013 | 2011 Suzuki Kizashi

1 Answer

Valve clearances


With such a late model car I suspect you have hydraulic tappets which means the clearance is automatically adjusted when you start

May 05, 2013 | 2010 Suzuki Kizashi

1 Answer

Where is the power steering reservoir for a 2011 Suzuki kizashi


There is not power steering reservoir for the Kizashi and for most of the automobiles since 2005. It is electrical.

Nov 25, 2012 | 2011 Suzuki Kizashi

1 Answer

Which way do the headlight vertical adjustments turn to raise the beam?


Turn on your headlights and locate the two adjustment holes that have the adjustment screws inside them on the sides of each headlight. The top hole has the vertical adjustment screw and the bottom hole has the horizontal adjustment screw. Turn the vertical screw clockwise to raise the beam and counterclockwise to lower; turn the horizontal screw clockwise to move the beam right and counterclockwise to move the beam left.

click this link for more help:--- http://technoanswers.blogspot.com/2011/05/how-to-adjust-headlight-beam-on.html --------- This should help.thanks.Helpmech.

May 29, 2011 | 2002 Chevrolet Corvette

2 Answers

Headlight adjustment


the screws for adjusting the headights are right next to the lights, they are phillips heads and are for adjusting the side to side, 
the adjusting screws for the up and down, are on the bottom of the headlights, and they are a small hole in the grill trim, these lights need a pretty long skinny screwdriver with a phillips head

Aug 17, 2008 | 1996 Suzuki Sidekick

Not finding what you are looking for?
2011 Suzuki Kizashi Logo

Related Topics:

481 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...