Question about Cars & Trucks

Open Question

Remove and replave Starter motor nissan terrano

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mrgreenz
  • 962 Answers

SOURCE: starter motor

  • If your testing indicates that the starter must be removed, the first step is to disconnect the negative cable at the battery.
  • It may be necessary to place the vehicle on a lift to gain access to the starter. Before lifting the vehicle, disconnect all wires, fasteners, and so on that can be reached from under the hood.
  • Disconnect the wires leading to the solenoid terminals.
  • To avoid confusion when reinstalling the starter, it is wise to mark the wires so they can be reinstalled on their correct terminals.
  • On some vehicles you may need to disconnect the exhaust system to be able to remove the starter.
  • Loosen the starter mounting bolts and remove all but one.
  • Support the starter while removing the remaining bolt.
  • Then pull the starter out and away from the flywheel.
  • Once the starter is free, remove the last bolt and the starter.
  • Once the starter is out, inspect the starter drive pinion gear and the flywheel ring gear.

Posted on Nov 07, 2008

jdwills
  • 15 Answers

SOURCE: nissan terrano headlight

check out
http://www.sferamydlo.com.pl/Zbyszek/Nissan/R20/el.pdf


Bulb Replacement
The headlamp is a semi-sealed beam type which uses a replacable
halogen bulb. The bulb can be replaced from the engine compartment
side without removing the headlamp body.
I Grasp only the plastic base when handling the bulb. Never
touch the glass envelope.
1. Disconnect the battery cable.
2. Disconnect the harness connector from the back side of the
bulb.
3. Pull off the rubber cap.
4. Press end of the retaining pin together to release bulb.
5. Remove the headlamp bulb. Do not shake or rotate the bulb
when removing it.
6. Install the new bulb in reverse order of removal.

Posted on Nov 11, 2008

  • 1 Answer

SOURCE: window not working

it could be the regulator for the window

Posted on Mar 03, 2009

  • 10 Answers

SOURCE: Removal of air bag

You should disconnect the batter and wait for 15 to 20 min before remove the bag because you want air bags to de energize

Posted on Apr 13, 2009

  • 1 Answer

SOURCE: heater plugs for nissan terrano 2

i have a nissan terrano 2.7 dti heater light not coming on some times dose and some times does'nt and it wont start

Posted on Mar 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi. Could you tell me which fuse controls the electric aerial. Nissan terrano ll 1996 import.


typically the fuze is under the hood. It is a inline fuze attached to the antenna motor.. I may be hidden under the fender, so find the motor for the antenna and follow the wires till you come upon the fuze holder. It comes apart with a twist, be sure to replace with the same value fuze. 2 amp usually. It has been my experience that these fuzes blow because of a short in the wiring or a short in the motor itself. so if your replacement fuze blows right after you put it in, you have more than a fuze problem.

Mar 03, 2015 | Nissan Cars & Trucks

1 Answer

Nissan terrano owners club


At a wreckers/parts dealers/eBay/ or similar. Depending on what is broken in your mechanism it may be possible to use a more commonly available Pareto repair the meh aims, e.g. The actual motors are quite common on other Nissan vehicles. Just watch that you get a right hand side motor..they are different to the left hand side ones! Check the model numbers on the casing.....

Jun 01, 2014 | 1999 Nissan Terrano

1 Answer

Leaking sun roof nissan terrano


I had the same problem, the drains were clean and it happened to be where the glass meets the seal on top, it killed my motor as there was moisture all the time. I did buy black silicone from screw-fix and its fixed. NO MORE LEAKING.

Oct 01, 2013 | 2005 Nissan Terrano 3.0

1 Answer

How do you replace a blown bulb in the clocks of a nissan terrano 2


With difficulty, as you have to remove the dashboard to do so. Some say fitting LED lights means you will never have to do this job again.........

Aug 04, 2013 | 2005 Nissan Terrano 2.7

1 Answer

Where can i find the engine no. of my terrano?


The engine number on Nissan products is on the right side of engine, right below valve cover.

Jul 27, 2012 | 2005 Nissan Terrano 2.7

2 Answers

I have a hard time starting my pathfinder sometimes, it wants to drag.


have got same problem with my 95 terrano deisel. if you leave for 10 or more seconds after glow plug light goes out it starts fine. aparantly they still glow after the light goes out.

Dec 27, 2011 | 1995 Nissan Pathfinder

3 Answers

91 nissan terrano wont start


First things first; 1) check Terminals and make sure tight & clean 2) Make sure the batteries good 3) Make sure connection from battery to starter is secured 4) Make sure its not the starter clicking if it is change it. 5) Make sure starter relay is good located with all fuses!

Jun 16, 2009 | 1991 Nissan Pathfinder

2 Answers

Nissan terrano headlight


check out
http://www.sferamydlo.com.pl/Zbyszek/Nissan/R20/el.pdf


Bulb Replacement
The headlamp is a semi-sealed beam type which uses a replacable
halogen bulb. The bulb can be replaced from the engine compartment
side without removing the headlamp body.
I Grasp only the plastic base when handling the bulb. Never
touch the glass envelope.
1. Disconnect the battery cable.
2. Disconnect the harness connector from the back side of the
bulb.
3. Pull off the rubber cap.
4. Press end of the retaining pin together to release bulb.
5. Remove the headlamp bulb. Do not shake or rotate the bulb
when removing it.
6. Install the new bulb in reverse order of removal.

Nov 11, 2008 | 2005 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...