Question about Cars & Trucks

Open Question

Iac valve not working for my 2001 suzuki esteem 1.8

Is there a way to clean it without replacing it?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: How do I remove the

I have a suzuki esteem 2000 and to remove the inside of the door panel you must first locate the window roll down lever and when you push back on the panel it opeans up a gap between the lever and the panel and if you look there is an axile that connects to the lever and in the lever there is a set of groovs and if you look at the groves there is a snap on ring, you must first push that ring off of the axile which will let you to freelly pull the lever off and then you can locate the screws that also hold the panel on my suzuki I have one on the handle which is covered by a plastic cap and there is also another palstic cap a little lower. After you have freed the screws the rest are just snap on clips you can just pull the panel off.

well hope it was helpfull.

Posted on Sep 12, 2008

Molson02536
  • 3854 Answers

SOURCE: IAC Valve Location - 1996 Jeep Grand Cherokee

The idle air control valve is located on the back of the throttle body. It has an oval electrical connector and two torx screws holding it in. Unplug the connector, remove the two screws then lightly tap the body with a soft faced mallet to loosen it from the body. 
Once you have it out and prior to installing a new valve clean the seat inside the throttle body where the idle control fits. This must be very clean! Installation is in the reverse order. 
 To save some cash, pull the valve out and clean it with throttle body cleaner, this usually fixes the problem for quite a while.
Good luck and hope this helps.

Posted on May 28, 2009

  • 22 Answers

SOURCE: 1993 Toyota Camry IAC cleaning

1) remove the black intake hose from the throttle body
2) get a can of throttle body/intake cleaner
3) be VERY careful if you decide to use the straw included with the can of cleaner, it can detach and go inside of your intake manifold.
4) spray inside and use a rag to remove junk from throttle plate(front and back side), hold the straw on the cleaner can and spray into the hole just ahead of the throttle plate, let soak for 10 minutes or so
5) reattach intake hose and start engine - you may get black smoke/rough idle for a minute as junk exits the engine

Posted on Jul 22, 2009

  • 1 Answer

SOURCE: how do i changing alternator suzuki esteem 2001

take it to a mechanic trust me, i had to replace mine after 6 days of trying to figure out how to remove the bottom bolt i took it to a shop if you need to know more email me KRAGAR33@AOL.COM

Posted on Dec 05, 2009

jgwhomeequip
  • 1902 Answers

SOURCE: how do i replace iac valve on 2001 ford escape

The IAC vavle is located behind the EGR valve on the driver side of the motor. You will disconnect 2 hoses and unplug the wire harness from the system. The unit will come right out. Just make sure that the hoses you take off go back in the same place. Also make sure that you have the negative battery wire disconnected. I had this same issue on my 2001 Escape, had to replace both the EGR and IAC so check both carefully.

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm working on a 2000 suzuki esteem 4 door car it acts like its not getting enough fuel but has good fuel pressure


The air filter is okay?
Personally, I would look at the MAF sensor - try disconnecting the electrical connector and driving the car. A warning light will appear on your dashboard, yes .. but if the car behaves as it should that points towards a faulty maf sensor.

Also try removing and cleaning your EGR valve

Here's a couple of links that may help:

Troubles with MAF sensor

MAF Sensor Suzuki Esteem


problems with egr valve and catalytic converter for suzuki esteem 98


You can also try disconnecting the O2 sensor - see what the car runs like.

My advice would be to NOT follow all the advice you get. Try things yourself. Your car runs ... but somewhere in the MAF sensor- EGR valve - O2 sensor there's a glitch. Do the simple things first - disconnect the MAF, clean the EGR ..

Apr 17, 2016 | Suzuki Cars & Trucks

1 Answer

How to remove and clean suzuki baleno 2001 fuel injector also tell where it is installed in engine.


Cleaning Fuel Injectors - YouTube

? 3:08
https://www.youtube.com/watch?v=MfMkNGlaQZo
Feb 25, 2011 - Uploaded by srmastertech
This video shows an example to what can happen when the fuel filter is not replaced. This vehicle has restricted fuel injectorscaused by excessive dirt in t... ... 2008-2010 Ford Super Duty CabRemoval & Installation Part I ...Missing: baleno

How to remove suzuki baleno blocked fuel injector for - Fixya

www.fixya.com/cars/t10217281-remove_suzuki_baleno
Aug 24, 2011 - How to remove suzuki baleno blocked fuel injector for cleaning. - Suzuki 2001 Esteem question.

Nov 21, 2015 | Suzuki Cars & Trucks

1 Answer

How do I replace a head light unit on a 2001 suzuki esteem passenger side


the whole assembly or just the bulb.?
post symptoms?
i was in a crash.
the lamp is just out, low beam is dead.
like that.???
in Europe the lamps have auto aiming , one more little possible.

this is covered ijn the operators guide, lost that, little gem?
open glove box. extract the guide, read that, RTM

or buy it for $4 bucks?
https://suzukipitstopplus.com/Products/1026-2001-2002-esteem-owners-manual.aspx

Oct 29, 2014 | 2001 Suzuki Esteem

1 Answer

Replace transaxle 2001 suzuki esteem


you need and expert mechanic to look and access this damage.
its non trivial.. and if not investigated proper can be very dangerous.

if really curious of all the long steps to do this,
alldata.com is your ticket.

Mar 19, 2013 | 2001 Suzuki Esteem

2 Answers

Where is the piont where you plug in the diagnostic connector on a 2001 petral vitara


The common faults on this engine are EGR valve and IAC valve.
The EGR causes rough running and cutting out,
The IAC causes just cutting out without the rough running, stalling at junctions etc is the usual complaint.
If you pm me the cars reg, chassis no etc i could see if i could email you the manual its a pdf so should be quite straight forward.

Jun 19, 2010 | 2001 Suzuki Vitara

1 Answer

How to check codes on a 2001 Suzuki Esteem


No, the only way to get the engine codes out of this car is to get the codes scaned. Auto zone offers free engine code scans. Hope this helped =)

Mar 04, 2010 | 2001 Suzuki Esteem

1 Answer

High Idle problem on 2001 Esteem 1.6L


Try cleaning your mass airflow sensor with carb cleaner.Soak it for a couple of hours.Do not soak electrical connector.

Feb 07, 2010 | 2001 Suzuki Esteem

1 Answer

2001 suzuki esteem check engine light flashing


there may be frozen valves forevap system if its that cold there get a diagnostic check done at any part store and they will suply you with trouble code and a deffinition of what the code is

Jan 12, 2010 | 1996 Chevrolet Monte Carlo

1 Answer

How do i changing alternator suzuki esteem 2001


take it to a mechanic trust me, i had to replace mine after 6 days of trying to figure out how to remove the bottom bolt i took it to a shop if you need to know more email me KRAGAR33@AOL.COM

Oct 11, 2009 | 2001 Suzuki Esteem

1 Answer

2000 sienna stalls, loses power and engine sounds muffled when I accelerate. idles at only 500 rpm at stop sign and runs rough


After about 100K + miles the idle air control valve (IAC) begins to collect carbon deposits that interfere with the movement of the spring-loaded valve. You will not be able to clean this without removal and dissembly of the IAC body. Use an emory cloth or fine sandpaper to remove the build up around the valve. This should free it up to rotate without binding. This is a temporary fix, of course, and will either require cleaning again or replacement of the valve. Getting to the IAC requires removal of most of the intake upto, but not including, the intake manifold. Total time is approximately 3-4 hours, but worth it. Good luck, and I hope this helps.

Jun 25, 2009 | 2001 Toyota Sienna

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75824 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...