Question about 1985 Toyota MR2

Open Question

My 1989 mr2 headlights always go up but sometimes go down and sometimes not. Help!!

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace headlight globes on mr2 sw20?


Turn headlights to on. Then 2 clicks back to turns lighs off but keep headlights up/open.

Remove headlight shrouds, (Black plastics.) Use phillips + head screw driver.

Remove chrome trim ring using phillips head screw driver.

Pull out headlight bulb. Disconnect from harness.

Reverse to install.

Sep 12, 2014 | 1991 Toyota MR2

1 Answer

Weres the temp gage fuse 1989 mr2


If the other guages are working its not a fuse cause the cluster is usually fused with one fuse. If your temp guage isnt working it is more likely the sensor on the engine.

Dec 31, 2011 | 1989 Toyota MR2

1 Answer

Remove headlight 2002 toyota mr2


Believe it or not, this is the headache to remove and replace the headlights:

Removal & Installation
  1. Remove the front bumper cover.
  2. Remove the tool box and the luggage compartment trim (carpet).
  3. Remove the 2 bolts and the nut.
  4. Disconnect the connectors, then remove the headlight

c17hydro_152.gif
  1. Front bumper cover removal-MR2



c17hydro_153.gif

To install:

  1. During installation, if the headlight is damaged, it can be reinstalled by installing new retainers.


c17hydro_154.gif

If the headlight is damaged, cut off these retainers



c17hydro_155.gif

Install new headlight retainers

Apr 19, 2011 | 2002 Toyota MR2 Spyder

1 Answer

Manual for 1989 Toyota MR2 and Idle problem.


gjo to alldata.com you will love it...
sawdust46

Jul 03, 2009 | 1989 Toyota MR2

1 Answer

Easy and best way to replace crank bearings in a toyota mr2 1989


if you meen the crankshaft, the engine has to be seperated from the transmission.

May 27, 2009 | 1989 Toyota MR2

1 Answer

Adjusting Headlamps


I have an 87 MR2 and this is how to adjust mine. Headlights have two spring loaded adjusting screws, one on the top controlling up and down movement and one on the side controlling left and right movement. The simplest method requires a blank wall 25 feet in front of the vehicle and a level floor. Position masking tape vertically on the wall in reference to the vehicle centerline and the centerlines of both headlights. NOTE: It may be easier to position the tape on the wall with the vehicle parked only a few inches away. Adjustment should be made with the vehicle sitting level. Starting with the low beam adjustment, position the high intensity zone so it is 2 inches below the horizontal line and 2 inches to the right of the headlight vertical line. Adjustment is made by turning the top adjusting screw clockwise to raise the beam and counterclockwise to lower the beam. The adjusting screw on the side should be used in the same manner to move the bean left or right. With the high beams on, the high intensity zone should be vertically centered with the exact center just below the horizontal line. NOTE: It may not be possible to position the headlight aim exactly for both high and low beams. If a compromise must be used, keep in mind that the low beams are the most used and have the greatest effect on driver safety. I typed this out of my "Haynes Manual 1985-1987 Toyota MR2 Book. I would think it would be the same method for a 1989 also. Hope this helps you. Redheadedwop

Sep 10, 2008 | 1987 Toyota MR2

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...