Question about Cars & Trucks

1 Answer

How to change out bearing

Noise in spin cycle

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 108 Answers

Bearing on what? and spin cycle sounds like maybe its a washing machine or dryer? but if it is a car, and youre talking about the wheel bearing, then youll have to jack up the wheel thats having the issue, remove the tire, brake caliper, brake rotor, then bearings can be either pressed in, or covered with a cap. (look up details for your specific vehical ahead of time, if its pressed in, dont bother, take it somewhere) if it is only covered by a cap, then you can usually get the cap off with a hammer and a flathead screwdriver, then the bearings will be behind it. make sure to note how they come out because they can be a pain to figure out! if you are going to install new ones, make sure to use LOTS AND LOTS of grease that you can pick up for cheap at any auto store, and is usually the size of a planter's peanut can, and should be light-medium brown in color. slap tons inside the area that holds the bearings, and on the bearings themselves. when in doubt, use more. then reverse the process to put them back on and CHECK THE BRAKES BEFORE DRIVING as taking the calipers off may mean you have to bleed any air out of the system before it will be safe to drive.

Posted on Dec 01, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Howling noise front end 2006 Chevy trailblazer what could it be


If the noise changes with engine rpm, possible bearing from one of the drive accessories. Idler pulley..tensioner pulley.. alternator bearing.. ac compressor bearing.. water pump bearing etc. If you remove the belt and spin all the pulleys by hand, usually a defective one will be heard/felt

Nov 21, 2015 | Cars & Trucks

1 Answer

Grinding/whining noise from gearbox/final drive - fiat 500C Lounge - 2010 model


I think removes the tyre both then check its gear box bearing noise or clutch plate bearing noise

Dec 16, 2013 | Cars & Trucks

1 Answer

What does a damaged wheel baring sound like


A bad wheel bearing noise will normally increase or roar loader with car speed but depends on how bad it is. If you turn momentary to the left or right while driving down the road say above 30 mph, the noise will change pitch either gettin loader or quieter. Locating the correct bearing to change can be tricky because sometimes it may sound like the left bearing but it can be the right. The best thing to do is to jack the car up on jackstands and get the wheels spinning and while spinning prob the hub area on the back side of the wheel with a mechanics stethoscope to pick up the sound. Placing the plastic end of a long screw driver against the ear while probing the inner hub with the other end works equally well for locating bearing noise. Compare the noise heard while spinning and the noisy one is the bad bearing. Do not spin the wheels fast while on jack stands or it could cause damage to the halfshafts (cv joints). Spinning the back wheels with be hard to do since there is no poweer to them. If they are bad enough, they will still make noise while someone is spinning them by hand. Most shops have a device for spinning the wheels.

Aug 06, 2012 | 2006 Infiniti M45

1 Answer

2.0 Liter, 2003 Rav4. Car had a ticking noise, Toyota replaced serptine belt and still makes ticking noise. Toyota says its lower engine rod bearings. I used stethascope and noise seems to be coming from...


big end bearings( lower engine rod bearings to confuse) knock at idle and get louder with rpm
if the noise changes with rpm and you are hearing it near the ac compressor then it could be the ac pulley bearing
test if it is the compressor by listening and then turning the ac off the pulley will still spin but the compressor stops
if the noise remains , replace the pulley bearings

Nov 16, 2017 | 2003 Toyota RAV4

1 Answer

Noise at rear wheel. Sounded like warn disc brakes. I replaced the disc brakes. Less noise but still not acceptable. Could it be a wheel bearing and if so how do I tell?


lift the rear axle off the ground and spin the wheels around as fast as you can. if the bearings are bad you will hear it if the sound changes as it spins. If it a scratching noise that will be from the disc brake pads

Jan 24, 2010 | 1999 Jeep Grand Cherokee

1 Answer

2001 Sebring LXI convertable. Loud rumbling noise that increases as accelerating increases. Sounds like a rumble strip on the highway. I changed the tires with no change in the noise.


Bad hub bearing. Drive the car on a straght EMPTY road .@30 mph or when noise is audible, **** the wheel left than right (similar to a race car warming. tires) and listen if there is a change in the sound if so its a front bearing if not it should be a rear bearing .Jack the rear of the vehicle up and spin the tire holding onto the strut. Feel and listen for a vibration or noise. This should pinpoint that elusive noise.Let me know Good hunting

Apr 11, 2009 | 1998 Buick Park Avenue

1 Answer

Its not a wheel berring i done changed that


its the bearing in the differential i'm affraid you can temperarily quieten the noise by spraying loads of lube into it but a new bearing (if not a seald diff) is a most definate

Feb 13, 2009 | 1993 Jeep Grand Cherokee

3 Answers

Changed brake pads and rotors on the front still have a roaring noise coming from drivers side front tire


if its like a humming noise its the wheel bearing if you ga straith and move the stering to one side noise there move to the other side noise is less wheel bearing gone lift the car in the front ans spin the wheel manualy listen to see whisht bearing make the noise change that bearing hope its a fix for you and rate a fixya for me if any other question feel free im here thank you pierre

Aug 06, 2008 | 1994 Saturn Sl

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14309 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...