Question about Cars & Trucks

1 Answer

Wiper transmission installation cost

I just would like to know what i most likely would be charged for wiper transmission linkage installation, already have the piece i would like to know an estimation on the labor

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 108 Answers

This really depends on the kind of car. shouldnt be too hard as the whole wiper system consists of under 10 parts. 1 electrical motor (easy to replace) and very simple linkage, all of which should be pretty easily accessable. so depending on the labor cost per hour, it should probably be around $100

Posted on Dec 01, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
maygemini
  • 147 Answers

SOURCE: 1999 Honda accord windshield wipers

hey you can unbolt them indiviually and tighten them in any position..but to remove open hood see the plastic cover bottom of windshield remove it ...basic hand tools... but to mess with the motor and the moving arm underneath you may have to pull the dash its hard takes several housrs..

Posted on May 08, 2009

smartr10U
  • 1305 Answers

SOURCE: Why so much to repair linkage for windhshield wipers?

Ask for a breakdown for parts and labor separate. Then get another quote from another reputable shop in your area... compare notes..

Posted on Jun 09, 2009

warlock61
  • 659 Answers

SOURCE: What is the average cost to fix the ignition coil?

does the vehicle have a single coil pack or is it coil on plug?

Posted on Jul 11, 2009

  • 108 Answers

SOURCE: Estimate of labor charges for replacing alternator

Typically the Silhouette and the Transport are the same vehicle. I spent about 45 minutes to replace the Alternator on my former Transport. It depends upon the prevailing Labor Rate what you will have to pay. I would guess somewhere around $75-$200 fro Labor alone.

Posted on Sep 20, 2009

SOURCE: how many hours of labor it takes to replace 2003

$400.00 to R&R Trans,e.g. remove and reinstall.
6 Hours
$1800.00 to rebuild
$2200.00 total

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wiper motor


Possible wiper linkage has broken/seperated from wiper motor. The wiper cowling covering the linkage assembly will need to be removed to inspect/repair

Feb 13, 2016 | 2008 Chevrolet Impala

1 Answer

Wipers stopped working. Both wipers sweep when one is moved manually. I think it's the wiper transmission linkage, but I'm not sure. Could it be just the bushing?


Turn on the wipers and listen you should hear the motor running if the Linkage broke, and since the wipers were out of range hitting off the glass that does sound like the linkage.

Mar 08, 2015 | 1997 Honda Accord

1 Answer

Wipers won't go home


Did the wipers stop in the up position? If so it may be a blown fuse or a defective wiper motor. Have you looked at the fuse-box? Did you mean that the wipers swipe the windshield correctly and then when the wipers shut off they stop in the wrong position. If this applies then inspect the wiper transmission. There could be worn/loose linkage between the wiper motor and the wiper arms. Also if the wiper motor was just installed. The clock position may be wrong. Please let me know if this information helps. If not please write back, leave more details, and I'll do my best, good luck.

Mar 25, 2014 | Lincoln Town Car Cars & Trucks

2 Answers

2007 pontiac windshield wipers stopped working and you can hear the motor still runs


Wiper Motor
  1. Remove finish caps.
  2. Make reference marks for installation and remove wiper arms.
  3. Remove the air inlet grille panel.
  4. Remove the bolts attaching the wiper module to the plenum.
  5. Carefully lift the wiper module out of the plenum.
  6. Disconnect the electrical connector from the wiper motor.
  7. Disconnect the clip retaining the electrical harness to the wiper module.
  8. Remove the wiper module assembly from the vehicle.
  9. Remove the wiper motor.
pgb3h4h2w2cfkigtemgbipamp4qbq234aaads=
Wiper module assembly and motor removal
To install:
  1. Install wiper motor and mounting bolts, tighten to 40 inch. lbs.(4.5 Nm).
  2. Connect the electrical connector to the wiper motor.
  3. Connect the clip retaining the electrical harness to the wiper module.
  4. Position the wiper module assembly into the plenum.
  5. Install the fasteners attaching the wiper module assembly to the plenum, tighten fasteners to 89 inch. lbs. (10 Nm).
  6. Install the air inlet grille panel.
  7. Install wiper arms and align to reference marks.
  8. Tighten wiper arm retaining nuts to 26 ft. lbs. (35 Nm).
  9. Install finish caps.

2010-11-13_221323_2007_pontiac_g6_wiper_cowl-m3h04eiq4trf45oprzz0vy4e-4-0.jpg
https://www.youtube.com/watch?v=dHJli8z1_jI
https://www.youtube.com/watch?v=A3hLLrwz8wQ

May 23, 2017 | 2007 Pontiac G6

2 Answers

WIPER MOTOR RUNS BUT WIPERS WONT MOVE


everyone will tell you that the linkage/transmission will need to be replaced but it doesn't,,most of the time its a bushing and O'Rielly's auto parts sells a "WIPER LINKAGE BUSHING ASSORTMENT" part# 49447 and it sells for about $5 bucks. Its fits tight and took a few minutes to install but its worth the trouble to save about $100

Feb 28, 2013 | 2008 Pontiac G6 Sedan

1 Answer

Ware is the wiper module located on a 2000 crown victoria


Follow the Dark Blue/White wire or Brown/White wire from the Multifunction Switch to the wiper module according to the schematic.
Also, one can trace the wires from the windshield wiper motor to the wiper module by peeling away the wiring loom and looking for a Yellow/Red wire that leads to the module.
---
Windshield Wiper Motor Removal & Installation To Remove:
  1. Remove the mounting arm and pivot shaft assembly.
  2. Remove the windshield wiper motor cover.
  3. Remove the clip.
  4. Disconnect wiper transmission linkage.
  5. Remove the bolts.
  6. Remove the motor.
To Install:
  1. Position the wiper motor.
  2. Install bolts. Tighten to 10 Nm (89 in. lbs.).
  3. Connect wiper transmission linkage.
  4. Install clip.
  5. Install wiper motor cover.
  6. Install mounting and pivot shaft assembly.
prev.gif next.gif

Oct 28, 2010 | 1999 Ford Crown Victoria

1 Answer

Need to know how to install the RH wiper linkage in a Nissan 200SX. I know how to remove the wiper arms and plastic cover below the windshield. Just need to know how to install the linkage with out...


The wiper cam actuator the cam is made to prevent damage to the motor by using a spring to allow it to slip if the wipers are stuck or frozen to the wind shield the spring stretching causes the wipers to stop in the middle of the window not hard to replace but does require you to do a timing procedure it should come in the box if not ill give you the basics get the new part remove both wiper arms careful the windshield is under the black plastic and I've seen other break the windshield taking the wiper arms off a battery post puller is the best way to remove , remove the cowl plastic piece you will see the cam gold/silver in color remove the one torx head screw then install new one rotate clockwise 2 times should spin freely then spin counter clockwise should stop look at where it is touching this area should have a 4mm gap the wiper motor has to be in the intermittent position prior to this turn key on put wipers in intermittent let motor spin then when it stops shut the key off then install cam.
--------
Removal Procedure:Tools Required:J 39232 Wiper Linkage Separator
Remove the wiper arms. Refer to Windshield Wiper Arm Replacement .
Remove the air inlet grille panel. Refer to Air Inlet Grille Panel Replacement .
Remove the water shield.Remove the screw and the nut.

Dissconnect the RH linkage assembly from the LH linkage assembly with the J 39232 .
Remove the LH linkage assembly.Remove the screw from the wiper motor.

Pull the wiper motor free from the slots of the bracket.Disconnect the RH linkage assembly from the wiper motor with the J 39232 .Disconnect the electrical connector from the wiper motor.
Installation Procedure:Tools Required:J 39529 Wiper Linkage Installer

Connect the electrical connector to the wiper motor.Connect the RH linkage assembly to the wiper motor with the J 39529 .
Important: When installing the wiper motor, be sure that the crank arm is in the innerwipe position. The crank arm drive pin must be engaged in the cam pocket.
Install the wiper motor with two locator pads pressed into the slots of the bracket.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
for getting more help on this issue please click on the link directly
http://www.adriatic-company.it/matizclub/tecnica/manualeII/M39d%20Wipers%20-%20Washer%20Systems.pdf
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Mar 07, 2010 | Nissan 200SX Cars & Trucks

1 Answer

Chevy blazer - windshield wiper arm spins on the post.


U will need to see if the small serrations that hold the arm are worn off, if they are u will need to replace the wiper arm and the wiper transmission linkage assembly, the post is not serviced separate, try finding a used one, they are common in salvage yards, a new wiper trans if it is still available will cost about $200

Dec 19, 2008 | 1996 Chevrolet Blazer

9 Answers

97 nissan sentra windshield wiper linkage arm disconnected


Most likely you will have to replace the wiper linkage from the center pivot to the left or drivers-side wiper pivot. The plastic piece in the linkage gets brittle over time and breaks down. To save a hassle in the future, replace both linkages. It should be under $20.00 for parts.

Jul 13, 2008 | 1997 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...