Question about 1992 Dodge Ram 350

Open Question

Where is the PCM located 1992 doge 3/4 ton truck

Engine code i get code 12 and truck wont start

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 218 Answers

SOURCE: getting 301 and 307 codes

CYLINDER #1 & #7 MISFIRE DETECTED.

Posted on May 12, 2009

Ad
  • 290 Answers

SOURCE: 1994 dodge truck codes 12 and 55

my source doesn't say much about these codes:
12 - direct battery input to PCM was disconnected in the last 50 key-on cycles
55- this code indicates a completion of all DTC's displayed on the check engine light

I'd guess they will eventuall go away but are not related to the starting issue

Posted on Jun 24, 2009

motor1258
  • 6674 Answers

SOURCE: I have a check engine light with a 12 and 24 code

Code 12 is battery disconnected lately. code 24 is faulty TPsensor. code 55 is end of message.
So, I'd replace my throttle position sensor.

Posted on Jul 08, 2009

  • 752 Answers

SOURCE: need location of fuse box on a 1985 Dodge 3/4 ton

Front seating area, driver side, under dash, below steering column, mounted in fuse block

Posted on Feb 20, 2010

e-Guru
  • 3917 Answers

SOURCE: My engine light is on

Hi

Trouble code P0700 means: Automatic Transmission Control System Malfunction.The P0700 is a general notice that there are codes in the TCM((transmission control module). To get to those codes you will need a scan tool capable of reading the TCM. Most aftermarket scanners are not capable of doing that and you will need a professional scanner.

Trouble Code B1661 in Dodge ram: Front Fog Lamp Control Circuit Open

For C20C1, you need to go to the car dealer because the code definition is unknown.

Please get back to us if you have further query or else please accept the solution.

Thanks for contacting fixya.com

Posted on Sep 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the egr valve located and the mass airflow sensor


the egr would have a tube coming from the exhaust and usually bolts to the intake, the mass airflow would be in between your air filter and the inake plenum, but the car doesnt use these sensors untel its in closed loop it wont enter closed loop untill the ect(engine coolant temperature) and the o2(oxegen sensor) heater curcuit is up to temp i would check to se if you have spark and fuel if not check for pcm codes but i would probably start with the crank sensor or pcm the crank sensor is the common

Oct 18, 2012 | 1992 Toyota Camry V6

1 Answer

What is firing order in doge ram 1500 1/2 ton 4wd pickup 5.9 liter v8


1-8-4-3-6-5-7-2. I googled your question and found the firing order there hope this helps. I do know on some engines the firing order is on the engine block of that motor.

Jun 12, 2012 | 1998 Dodge Ram 1500 4WD

1 Answer

Code 12 1995 dodge spirit 2.5 battery and PCM NOT disconnected. where does the pin 3 on PCM gets its battery suppy voltage from


Has the battery been disconnected or been low on charge in the last 50 ignition cycles?

Code 12 means that battery power has been disconnected within the last 50 ignition cycles. it does not mean there is no battery power to the computer

Pin 3 should be a red/white wire that is the constat power supply to the PCM. It is protected by a fusible link located neer the drivers side strut tower. If that link was bad the car would not start or run as it also supplieds power to the asd relay, fuel pump relay, and the ssd relay.

I would put money on the the problem being igntion (plugs wires cap rotor), compression (low cylinder compression usually cylinders 2 and 3), lack of fuel delivery (low fuel pressure, a weak or dirty injector), timin (timing belt jumped, worn distributor, look exciter ring), or possibly a plugged catalytic converter.

I would check compression first especially cylinders 2 and 3. It was pretty common for the head gasket to fail in between these two cylinders.

Feb 24, 2012 | 1995 Dodge Spirit

1 Answer

92 Doge Dakota Sport w/3.9 2 door extended cab 5 speed. Truck is sputtering and back firing. was doing the sputtering at 40 to 45mph. then ck engine light came on when checked no code. has OBD1 system....


If it idle fine and stumbles on acceleration your are looking at a spark grounding out, If it cant idle starts then dies your MAP sensor has problems,

Apr 30, 2011 | 1992 Dodge Dakota

1 Answer

1994 Grand Cherokee, 5.2 V8 shuts off when hot. Cool for an hour or 2, starts up after a half hour or so, then dies again. No trouble codes except 12 and 55; I pulled fuses to check them, hence the code...


NOTE: With the jeep cherokees. the Check Engine light if continuously driven with it on for more than 25 minutes whilst still traveling will engage the "PCM self protect" usually around the 27minute mark,and shut down the vehicle, and yes it takes 90 minutes to reset,

you might find that you will arrive ok, at your destination with this issue... pull up, and then it wont start again a few minutes later, this is the PCM Shutdown protection.....when the check engine light is on means the PCM is reset,found the error and why you can only run the car with the check engine light for about half an hour.

"You can however drive and turn the car off and coast in neutral and turn on the vehicle again to buy yourself more time with the "Check Engine time limit shutoff"

happened to me in mine, the error codes never showed up for the crankshaft position sensor
either...

i replaced the crankshaft position sensor under the transmission case, and it got rid of the issue this crank sensor is a common cause of the cherokees , it could no longer read the speed of the crankteeth. and can't get a reading the car is still running hence the shutdown, also you will find it also controls the PCM to engage your second fan on the radiator because it cant tell the vehicle is still running, and causes the PCM to get confused and wont let the rest of the engine function properly ie: coolant sensors, and Thermostat sensors, and you will find it overheats and needs to cool some times...which is why the PCM shutsdown the car.....try the crankshaft position sensor replacement under the transmission it's usually the cause of this on all cherokees "makes no difference if its a V8 or not by the way, same thing happens on 4.0 straight six engines also" .

Apr 26, 2017 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Doge dash flash codes 2002 ram 1500 2w 4dr 4.7 it flashs 12 times


code 12 problem with battery connection. direct battery input to pcm disconnected within the last 50 ignition key-on cycles. simple to say that u disconnected the battery at some time and reconnected it and it set that fault code. nothing to worry about. hope this will help!!!

Apr 06, 2010 | Dodge Ram 1500 Cars & Trucks

1 Answer

1260 code wont start


P1260 - This, basically is indicating that a theft has occurred, and the engine has been disabled.If the engine stalled, during travel, and the code was pulled after the stall, this will indicate the following:

1.A loss of power, or ground wire to the PCM
2.A Faulty PCM power relay
3.A Faulty EEC power diode
4.A Faulty VERF signal.

Passive Anti-Theft System (PATS) communicates PCM through instrument cluster to enable or disable vehicle's engine. Within one second after engine start, PCM must receive an enable signal from instrument cluster or engine will be disabled. Along with enable signals, instrument cluster and PCM share messages that confirm security codes shared during initial installation. This shared security data makes instrument cluster and PCM a matched pair, so neither will operate in another vehicle. When system is functioning properly and ignition switch is turned to RUN or START position, THEFT indicator light will turn on for 3 seconds, then turn off. Vehicle will be enabled to start and run. If a problem exists in PATS, THEFT indicator light will stay on or flash continuously.


NOTE_ The best action is to clear the code, by using a diagnostic CPU. Plug the CPU into your in car port, under the dash. Follow the instruction on the CPU display to clear the code. if the engine dose not start after the code is cleared, this will indicate that there are some issues with the PCM, or PATS

Nov 11, 2009 | 1999 Ford Taurus

1 Answer

I have a check engine light with a 12 and 24 code followed by the55 code . The car is often difficult to start.It's 1992 Dodge Spirit with a 4cy. engine.


Code 12 is battery disconnected lately. code 24 is faulty TPsensor. code 55 is end of message.
So, I'd replace my throttle position sensor.

Jul 07, 2009 | 1992 Dodge Spirit

2 Answers

Car wont start but will turnover


ya hi there do you know motor size and year ? can you locate the ignition coil ? if so check to see 12 volts is present when you turn ignition to start position? check all fuses and also check relay's take each relay out and wiggle back in might be a bad connection .

Jul 12, 2008 | 2005 Dodge Magnum

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...