Question about 2005 Ford Mustang

Open Question

05 mustang 4.0l po171 lean condition

Po171 bank 1 lean condition common causes and repair

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

daves944
  • 1050 Answers

SOURCE: vehicle failed emissions testing

You need to replace the intake upper plenum gaskets. There is two pieces, a top cover with one big silicone o-ring gasket and a lower half with six smaller silicone o-rings for the individual intake ports. You can buy these as a set, just for this job. Start this job by removing the wiper blades, then release all the screws, (including the ones that support the wiper motor), that hold that big black plastic valence at the back of the engine compartment. Pull that out of the way, you will have to pull the windshield washer hose through it, just disconnect it on the engine side, now you have access to the plenum. It's a pretty easy job now to remove and replace both halves, just a bunch of 8mm screws hold it all together. Take notes or digital pics along the way so you can pop it all back together. My only caution would be; when you have it apart, do not drop anything in the intake port! I always stuff kleenex in these while I'm working in case something slips out of my hands. Also, don't over tighten, it's all plastic. If you don't want to do it yourself, a shop should charge about an hour and a half, plus the codes must be reset and the van driven until all the monitors are ready.

Posted on Mar 26, 2009

  • 290 Answers

SOURCE: ford windstar codes po171 and

Try cleaning the MAF. Here is more info on the codes:
http://www.aa1car.com/library/ford_lean_codes.htm

Posted on Apr 14, 2009

  • 1 Answer

SOURCE: code po171 and po174. fuel bank 1 & 2

how can i correct code po171

Posted on Aug 24, 2009

  • 784 Answers

SOURCE: Generic code PO171 system 2 lean bank 1 generic

This can be caused by a faulty mass air flow sensor

Posted on Jul 09, 2010

SOURCE: check engine light is on

Look for vacuum leaks,that are causing the O2 Sensors to go lean, and set codes on both banks

Posted on Nov 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bank 1 system too lean code po171 how to repair


code p 0171 refers to system too lean bank 1===causes --intake/exhaust leak---AIR system---MAF/VAF sensor---fuel pressure/ pump/ pressure regulator---injector/s---heated oxygen sensor (HO2S unit in the exhaust manifold or before the cat converter
If the engine is running well then consider replacing the HO2S unit as that reports to the ECM that then adjusts the mixture for that bank by altering injector amounts and timing
all the rest affect both banks but the code is bank 1 specific

Sep 18, 2016 | Cars & Trucks

1 Answer

Code po171 system too leen bank 1


DTC P0171 - System Too Lean (Bank 1)
Basically this means that an oxygen sensor in bank 1 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1.

Note: This DTC (Diagnostic Trouble Code) is very similar to P0174, and in fact your vehicle may show both codes at the same time.

I would suggest that you take a look at the front oxygen sensor. Typically speaking the oxygen sensor causes this code to appear. Here is the possible cause list from the manual for your car.

Trouble Code: P0171 - Fuel System Lean (Bank 1)

Possible Causes:
Air leaks in intake manifold, exhaust pipes or exhaust manifold
Base engine mechanical problem causing a lean A/F condition
Fuel control Sensor is out of calibration (e.g., ECT, IAT or MAP)
Fuel delivery component fault (clogged filter, low fuel pressure)
O2 element is contaminated, deteriorated or it has failed
Vacuum hose is disconnected, broken, leaking or loose

Hope this helps (remember to rating this answer ans leave us a testimonial comment). Thank you for using FixYa.

Oct 12, 2011 | 2000 Ford F150 Flareside SuperCab

1 Answer

2003 Chrysler Town & Country po171 code


DTC P0171 - System Too Lean (Bank 1)
Basically this means that an oxygen sensor in bank 1 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1.

Note: This DTC (Diagnostic Trouble Code) is very similar to P0174, and in fact your vehicle may show both codes at the same time.

I would suggest that you take a look at the front oxygen sensor. Typically speaking the oxygen sensor causes this code to appear. Here is the possible cause list from the manual for your car.

Trouble Code: P0171 (2.5L V6 Auto) - Fuel System Lean (Bank 1)

Possible Causes:
Air leaks in intake manifold, exhaust pipes or exhaust manifold
Base engine mechanical problem causing a lean A/F condition
Fuel control Sensor is out of calibration (e.g., ECT, IAT or MAP)
Fuel delivery component fault (clogged filter, low fuel pressure)
O2 element is contaminated, deteriorated or it has failed
Vacuum hose is disconnected, broken, leaking or loose

Hope this helps (remember to rating this answer ans leave us a testimonial comment). Thank you for using FixYa.

Oct 12, 2011 | 2001 Chrysler Town & Country

1 Answer

2005 lincoln aviator codes po171 po174 p2195 p2197


This DTC is a very common issue on the V6 and refer at the little rubber elbow on the PVC wears through.

P0171 - System Too Lean (Bank 1)

P0174
- System Too Lean (Bank 2).

Those lean codes are for a lean fuel condition. The first thing I would check is for a vacuum leak. Especially look around the PCV system. Look for soft or collapsed hoses in the PCV system, (especially the rubber elbows) these are very common issue for failure and cause of lean codes. Also check around the intake manifold for leaks or any other hoses that may have come off.

Next I would check fuel pressure and the fuel filter for blockage. If the filter is old you might as well replace it. If and when you find an issue you will have to have a scan tool to reset the check engine light before you go back through emissions.

Check that stuff and let us know what you find.

Sep 30, 2011 | 2005 Lincoln Aviator

1 Answer

2001 gmc jimmy po171 lean bank code what could be the fix is it a possable o2 sensor


More than likely bank 1 sensor has a possible vacuum leak, or a lean misfire on that side of the bank.(lean misfire happens when gap of spark plug are exceed due to wear), As for the 02 sensor I agree that it is reporting the true engine condition on that side of the bank

May 01, 2011 | 2001 GMC Jimmy

1 Answer

Rough idle vibrates and po171 code service engine soon. jamesrowland9@aol.com


Hi, a Ford P0171 is a LEAN code for cylinder bank 1, and P0174 is a LEAN code for cylinder bank 2. These codes commonly occur on many Ford vehicles, and are set when the powertrain control module (PCM) sees the air/fuel mixture is running too lean (too much air, not enough fuel).
When the Check Engine Light comes on, either one of these codes, or both, may be found when a code reader or scan tool is plugged into the vehicle diagnostic connector. IF the vehicle is driven long enough, typically both codes will be set.
A P0171 lean code for bank 1 is the cylinder bank on the RIGHT (passenger) side of the engine on Ford vehicles with a V6 or V8 engine and rear-wheel drive.


A lean fuel condition may exist if the engine is sucking in too much air and/or the fuel system is not delivering enough fuel. If bad enough, a lean fuel condition may cause lean misfire, a rough idle, hesitation or stumble when accelerating, and/or poor engine performance.
Unmetered air can enter the engine through a vacuum leak, a dirty airflow sensor that is not reading airflow accurately, an EGR valve is not closing and is leaking exhaust into the intake manifold, an EGR valve that is allowing too much flow (because the EGR differential pressure sensor that monitors EGR flow is faulty and is under-reporting EGR flow).
If the problem is not enough fuel, the underling cause may be a weak fuel pump, restricted fuel filter, leaky fuel pressure regulator or dirty fuel injectors.

Mar 24, 2011 | Ford Escort Cars & Trucks

2 Answers

Ford f150 2003 po171 always lean bank 1. replaced bank 1 o2 sensor smoked intake. replaced egr valve. still code po171 short term trim 0123 but long term trim is up bank 1 30 anb bank 2 is 27. idle is a...


Code Po171 indicates a lean condition on cylinder bank #1 of the engine. This is the drivers side of the engine. I would suggest replacing both front oxygen sensors as a pair to start. An oxygen sensor has a life span of about 5 years and yours are now 9 years old if they are original. When they get older they are slow to respond to changes in the oxygen content of the exhaust and can trigger a code Po171. If you continue to have the same code set after the replacement of both oxygen sensors then it is time to find out why your engine is running lean. Some of the most common causes are an ignition misfire and a vacuum leak. I have also seen Fords EGR flow sensor (known by Ford as Delta Pressure Feedback sensor) to cause problems like that as well. A good mechanic with a scan tool can usually spot a problem like that in a few minutes.

Mar 01, 2011 | Ford F-150 Cars & Trucks

1 Answer

Generic code PO171 system 2 lean bank 1 generic


This can be caused by a faulty mass air flow sensor

Jul 06, 2010 | 1999 Ford Taurus

2 Answers

2002 Chevy Van with a 3400 code po171 too lean how to fix


Code PO171- Lean mix of Bank 1.
Code PO174- Lean mix of Bank 2.

Most of the time a P0171 and P0174 is caused by either a vacuum leak--more than likely the PCV hose and valve or a dirty or defective Mass Airflow (MAF)sensor. Low fuel pressure can also cause this condition. The PCV hose is located on bank one but can affect both sides because the other end is located on the back of the upper intake manifold. Usually they deteriorate and get a hole in it.

Clean the the MAF sensor with MAF cleaner, which you can pick up at any Auto parts store and also pick up a bottle of fuel injector cleaner. Good luck and hope this helps.

Nov 16, 2009 | 2002 Chevrolet Venture Passanger

2 Answers

My 97 buick stalls some time and wont start for while


remove maf sensor and check for air filter debris on it, gently blow off debris taking care not to damamge the wires on the sensor. also check forvaccum leaks as this can cause a lean condition

Nov 28, 2008 | 1997 Buick LeSabre

Not finding what you are looking for?
2005 Ford Mustang Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...