Question about Ford Fusion

Open Question

2006 ford fusion 5 speed push clutch in and its hard or impossible to get car into gear if you pump the clutch it will go in to gear and works fine ,, clutch slave cylinder ??

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 208 Answers

SOURCE: Removal of slave clutch master cylinder

The hydraulic cylinder is in the bell housing. When you separate the motor and tranny, you will see it as a unit with the throw-out bearing. Take the hydraulic line off before you start. You will have to bleed it when you are done.

Posted on Aug 13, 2008

  • 26 Answers

SOURCE: slave cylinder or clutch? or both?

it internal and pretty much alot of work. You have to pull the transmission out

Posted on Aug 25, 2008

motor1258
  • 6674 Answers

SOURCE: 1994 chevy camaro 3.4manual 5 speed

You may want to read bleeding instruction at this link, it may shed some light.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b886d

Posted on Jan 31, 2009

csmock132
  • 4669 Answers

SOURCE: on my 1987 ford thunderbird turbo coupe 5 speed it

Are you having to add fluid? If yes, look for the leak. If no, It's the clutch master cylinder.

Posted on Apr 05, 2009

germcelchar
  • 389 Answers

SOURCE: 2006 ford ranger can not bead the slave cylinder

I dont want to make you feel silly but it seems like you loosened a grease nipple and not a bleed screw. A small amount of fluid (if the slave cylinder is not new) is normal. Their is no way grease can get into the fluid system. Take off the feed pipe to the slave cylinder Try pumping the pedal or use your vacuum pump from there.Get someone to pump the pedal holding your finger on the end of the pipe to see if their is any preasure comming that far if not its your master cylinder if you have preasure check the slave cylinder again for a bleed screw. It seems more like the master cylinder unless it ran out of fluid otherwise how did air get in. You should also check if the slave cylinder or the bar comming from it is adjustable Sometimes their is a screw on the bar others have oblong holes to move the slave cylinder back or forward

Posted on Aug 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My clutch is getting stuck and not coming back up when I release it, it's a 2006 Ford Fusion


On the WEB

2006 Ford Fusion Clutch questions - AR15.Com Archive

https://www.ar15.com/archive/topic.html?b=1&f=134&t=1697699
Dec 18, 2014 - 4 posts - ‎3 authors
2006 Ford Fusion Clutch questions - AR15. ... Clutch pedal stops half way up intermittently yesterday. Today stuck on floor. ... With the rope you can get into a pushdown...pull up rythm on the pedal without having to stop to get

Jul 31, 2015 | Ford Cars & Trucks

1 Answer

I have a Ford fusion 2003 and I can't change into 5th gear. Is it the clutch or gear box?


Gearbox. synchronizers or bearings. Or both. 5 speeds had a problem with the fifth gear bearings. Which I have seen to take out the synchronizers. Rebuild the transmission.

Nov 16, 2014 | Cars & Trucks

1 Answer

I've been having problems with my cruise control, 2006 Ford Fusion SE. Sometimes it will set correctly and sometimes it doesn't. At times if I brake hard I can hit the off button and it will set...


cruise controls are funny things
you have to accelerate to a speed then turn it on and press set
It will cruise at that speed
if you touch the brake it will unset and you will have to press on the accelerator again to the speed and pres resume
if you want to accelerate to pass just press the accelerator until you have passed , then just take your foot off the accelerator and it will coast until the set speed
if you change gears , it will unset
if you touch the brake , it will unset
if you have it set and find the speed to fast , hold the set button and it will slow down to the speed you want
let the button go and it will set at the speed
if you want to go faster than the set speed press the resume button and it will speed up until you get the speed you want
from your description of the problem , it appears that you have misread the instructions in the owners manual

Mar 28, 2017 | 2006 Ford Fusion

2 Answers

Clutch pedal sticks to the floor; the brake reservoir was low


I believe your pressure plate is broken and at a minimum will have to be replaced along with the clutch disk.

Jul 04, 2010 | 2006 Ford Fusion

1 Answer

Moaning, whining sound when the clutch is depressed. Gets louder when revving the engine. 2006 Ford Fusion 4 cyl 5 speed manual. I think it might be the throwout bearing but not sure. Don't know if the...


last one or i will not get up for work tomorrow,its the thrust bearing ,**** plastic fittings used ,when it goes completely ,just renew the whole lot ,if you drop subframe then they are easy to change ,about 2 hrs, but you mush drop the subframe ,its only 4 bolts two either side

Jan 12, 2010 | 2006 Ford Fusion

1 Answer

The revers gear grinds when selecting. and jumps out of 1st gear please can you help my car is a ford fusion 05 with a 5 speed gear box the clutch system has been bled and the master cylinder is not...


sounds like a synchro is going or you may just need a simple linkage adjustment either way id take to shop unless you are a transmission rebuilder?

Aug 24, 2009 | 2005 Ford Fusion

1 Answer

6.5Lchev diesel to a ford ZF 5 speed gear box


You will need the Chev pressure plate to suit the Chev flywheel and a clutch plate to suit the Ford ZF gearbox. Ford ZF throwout bearing and clutch fork should be fine.

Jul 01, 2009 | 1981 Ford F 100

1 Answer

Transmission fluid


Transmission
fluid
Motorcraft SAE
75W-90 gear oil
(non-synthetic)
Manual transaxle 3.0 quarts
(2.87L)3
Motorcraft FNR5
Automatic
Transmission
Fluid
5–speed
automatic
transaxle
7 quarts (6.7L)4
Premium
Automatic
Transmission
Fluid
6–speed
automatic
transaxle
7.4 quarts
(7.0L

Oct 26, 2008 | 2006 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...