Question about Honda Accord

1 Answer

Re: 2004 Honda Accord The interior courtesy lamps above overhead in front seat area are both out. I want to change the bulbs but can't figure out how to gain access to the housing.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 141 Answers

Small srewdriver to either of the longsides will pop the lense out and allow access to the bulbs.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the location to replace overhead lights fuse in 2003 oldsmobile aurora


Rear fuse box. INT LP 10 amp . there is also INT LP relay in the same rear fuse box .
Fuse Block - Rear
Under the rear seat, on the left side of the floor pan
The INT LP fuse in the fuse block - rear supplies battery positive voltage to the normally open switch contacts of the INT LP relay. The INT LP fuse also supplies battery positive voltage to the INT LP relay control circuit. The fuse block - rear also supplies battery positive voltage to the relay control circuit for the front courtesy lamp. The door modules communicate on a simple bus interface (SBI). When you open any door, the switch contacts of the door open switch close. When a door open signal circuit is grounded, that door module sends a message to the drivers door module (DDM) in order to indicate that a door is open. The DDM sends a class 2 message to the rear integration module (RIM) in order to indicate which door is open. The RIM activates the INT LP relay in order to provide battery positive voltage to the interior courtesy lamps. When any front door is opened, the RIM will energize the FRT CTSY lamp relay grounding the I/Pcourtsey lamps at G302. Depending on which doors are opened, front or rear, the proper interior courtesy lamps illuminate. The RIM provides a pulse width modulated ground to all interior courtesy lamps for the interior lights theater dimming feature. Some of the courtesy lamps are also used as reading lamps, each reading lamp may be manually turned on or off using it's own respective switch

Sep 24, 2015 | Oldsmobile Cars & Trucks

2 Answers

Interior lights not working


You mite have a DTC - diagnostic trouble code stored in the BCM - body control module , The BCM controls the interior lights ! Have you heard of a BCM ?
DTC B2615
The body control module (BCM) receives a ground signal from the door jamb, liftglass/liftgate, or courtesy lamp switches requesting courtesy/dome lamp illumination. When this occurs, the BCM directly sends a voltage through the courtesy lamp supply voltage circuit illuminating the courtesy/dome lamps.
Conditions for Setting the DTC
?€¢
When the BCM receives a courtesy lamp illumination request signal and the courtesy lamp supply voltage circuit is shorted to ground.

?€¢
When the BCM is not receiving a courtesy lamp illumination request signal and the courtesy lamp supply voltage circuit is shorted to voltage or open only to the first splice from the BCM.

?€¢
There is a loss of the rear fuse block TBC 3 battery supply voltage to the BCM for more than 1 second

Diagnostic Aids
?€¢
Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

?€¢
Only an open circuit up to the first splice from the BCM will set DTC B2615.

DTC B3801
The body control module (BCM) monitors the courtesy lamp switch signal circuit in order to determine when the courtesy/dome lamps should be illuminated. When the BCM senses that the courtesy lamp switch signal circuit is grounded when the switch is activated, the BCM will directly illuminate the courtesy/dome lamps. Do you know what a scan tool is ? not a code reader !
Courtesy Lamps Inoperative




GM Tech 2 Training video 1996

Aug 24, 2015 | 2004 Chevrolet Chevrolet TrailBlazer EXT

2 Answers

2009 dts inside lights stay on


this could be a door switch problem or a BCM problem. access the BCM for codes and data this will help. check to make sure the headlight switch for the interior lights is in the off position.

Mar 20, 2015 | 2009 Cadillac DTS

2 Answers

2008 ford explorer light control module


Hi Rich , what lights are you talking about ? Exterior Lighting , Interior Lighting ? It doesn't matter All lights are controlled by SJB smart junction box ! An you can't just stick in a used one , It will need to be programmed ! Interior Lighting The interior lighting system consists of the following components:
  • Smart junction box (SJB)
  • Dimmer control switch
  • Interior/map lamps
  • Cargo lamp
  • Glove compartment lamp
  • Vanity mirror lamps
  • Door ajar switches
  • Puddle lamps
The interior lighting system consists of 2 subsystems:
  • Courtesy lamps
  • Demand lamps
The courtesy lamps are controlled by the SJB. The courtesy lamp subsystem consists of the interior dome lamps, the puddle lamps and the overhead console lamps (if equipped). The SJB supplies voltage to the courtesy lamps when the SJB receives the required input.
The demand lamps are controlled by the SJB. The demand lamps subsystem consists of the glove compartment lamp, all map/reading lamps, and the left and right vanity mirror lamps.
The SJB supplies power to the interior lighting system. The SJB will set DTCs if certain circuit failures exist with the interior lighting system.
Exterior Lighting Headlamps
The headlamp system is a dual-beam pattern system. It consists of a low and high beam, with a replaceable bulb. The headlamp assembly has the park/turn indicator lamp integrated into the headlamp assembly. The smart junction box (SJB) supplies voltage to the headlamps when demanded.
Principles of Operation
The SJB receives inputs and delivers outputs to a majority of the electronically-controlled features of the vehicle. The SJB constantly monitors the systems under its control and reports a concern in the form of a DTC. The DTC can be retrieved with a scan tool through the medium speed controller area network (CAN) communication network.
NOTE: Prior to the removal of the SJB, it is necessary to upload the module configuration information to the diagnostic tool. This information must be downloaded to the new SJB after installation. For additional information, refer to Section 418-01 .

Feb 25, 2015 | 2008 Ford Explorer

1 Answer

Interior courtesy light


Page 116 and 117 of the manual explain that there's a two-position slide switch on the map light, DOOR and OFF. The back light has three positions, ON, Door Activated, and OFF.

Pages 116 and 117:
http://techinfo.honda.com/rjanisis/pubs/om/ACC080/ACC0808OM.pdf

Dec 12, 2013 | Honda Cars & Trucks

1 Answer

How do you change a front signal bulb on a 2004 accord


Front turn signal bulb replacement

1. Remove the inner fender
2. Disconnect the 3p connector from the front turn signal/side marker light.
3. Turn the bub socket ( 45 degree ), counterclockwise to remove the bulb.
4. Install a new bulb in the reverse order of removal.

Apr 12, 2010 | 2004 Honda Accord

1 Answer

Interior lights


bad electrical grounds ... check all systems for poor grounds ..first poster... you have water or moisture issues as well as perhaps ground wiring issues causing premature faliures of bulbs and other.. the lens' pop off to replace bulbs

Oct 30, 2008 | 2006 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...