Question about Ford Ranger

Open Question

Where is the Location of fuel pressure regulator 1986 ranger 2.9?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
daves944
  • 1050 Answers

SOURCE: rough idle,runs fine on highway

It is possible that the regulator is leaking into the intake plenum, or one of the injector lines has a bad O-ring and is doing the same thing. This was actually a big problem with this system on the 4.3L engines, but it is a little different on the 5.7. Before tearing into this this though, I think it would be a good idea to get a professional diagnosis. I would start with a compression test. The miss could be caused by low compression in one or more cylinders. The injector assembly has the regulator mounted right on the side of it and the whole assembly resides inside the intake plenum. It is not that difficult a job, requires some patience and skill, the worst part is the cost of the parts.
I've attached a picture of the injector assembly with the reg attached and highlighted

9533d3a.jpg

Posted on Mar 19, 2009

Ad
  • 92 Answers

SOURCE: fuel pressure regulator had no vacuum line connected

another engineers wet dream. think of it this way . what is normally in the intake when the engine is running.. answer vacume, hence the regulator gets its vacume without a hose connected to it as its already in a full time vacume chamber.no hose required . ps be carefull to seat the regulator and o rings securely into the housing befor you reattach the secureing metal clip.
good luck chris

Posted on Mar 23, 2009

keemo68
  • 1263 Answers

SOURCE: fuel pressure regulator location

the fuel pressure regulator is on the fuel injector rail. it is where the fuel line for input connects to

Posted on May 02, 2009

  • 6982 Answers

SOURCE: fuel pressure regulator

Two places to look...if you have separate injectors for each cylinder then regulator should be at the front end of the fuel rail. If you have throttle body injection it is on the throttle body itself.

Posted on Jul 30, 2009

  • 149 Answers

SOURCE: Fuel pressure regulator location on a 2002 Dodge

The regulator is in the fuel tank. You must drop the tank to get to the system It is part of the fuel pump/fuel pressure regulator/fuel level sending unit. If just changing the regulator which you can,make sure you install new o-rings, put a little clean gas on them to install. Cheaper than a new fuel pump.

Posted on Jan 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whereisthefuelfilterlocatedona2.2lmotor


Chrysler Laser fuel filter location Questions & Answers - Fixya

www.fixya.com > ... > fuel filter location > Cars & Trucks > Chrysler
Chrysler Laser cars & trucks fuel filter location questions and answers. ... i need to know where the voltage regulator is located on my 1986 chrysler lasr 2.2 l ...

Sep 24, 2015 | 1986 Chrysler Laser

1 Answer

Fuel pressure regulator location


Depending on the year of the truck, it should be on the fuel rail near the injectors.

Jul 22, 2013 | Cars & Trucks

1 Answer

1986 Ford Ranger 2.9 EFI sputters and stalls after it warms up.


Could be the ignition module or a fuel problem.
Have you checked the fuel pressure ?

Jul 01, 2012 | 1986 Ford Ranger 2WD

1 Answer

1988 ford ranger fuel pumps both come on for 2 seconds and go off.\r\nevery time i turn the key this happens. can i wire the pumps to a hot wire whenever the key is on they will run?


the pumps should run for a couple of seconds then shut off when the regulator determines the fuel pressure is correct. If you wire it, it will probably shorten the life of the regulator since pressure will constantly be applied to the regulator.

Apr 18, 2011 | 1988 Ford Ranger

1 Answer

My 1986 ford ranger 2.9 v6 engineafter driving for a while it sputters from gas and stalls.does it have (2) fuel pumps? 1 in the outside frame and 1 in the tank?


Yes there are two (2) fuel pumps on these pickups, one low pressure one in the tank that gets the fuel to the high pressure pump which is in the inside of the drivers frame rail beneath the cab towards the front of the cab.

Jul 01, 2010 | 1987 Ford Ranger

2 Answers

Where can i obtain a diagram of the location of


the fuel filter is located on the inside of the frame rail on the drivers side about where the driver seat is bolted to the floor board, it is round and about the size of a coke can

Apr 20, 2010 | 1986 Ford Ranger 2WD

2 Answers

Fuel pressure regulator location


the fuel pressure regulator is on the fuel injector rail. it is where the fuel line for input connects to

May 02, 2009 | 1999 Mercedes-Benz E-Class

1 Answer

86 ford ranger


its under the carpet on the passanger side at the firewall

Jul 20, 2008 | 1986 Ford Ranger 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...