Question about 2003 Ford F250 Super Duty Crew Cab

Open Question

Torque specs for ford f 250 pinion nut - 2003 Ford F250 Super Duty Crew Cab

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: torque specs foe 4.9 ford f150 flywheel

75-85 ft lbs

Posted on Mar 04, 2009

chuck943
  • 783 Answers

SOURCE: torque specs 7.5 inch rear axle 96 ford ranger

Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Posted on Jan 30, 2009

  • 207 Answers

SOURCE: Head gasket torque specs

Here you go, I hope this is what you were looking for:

For 1987-94 models, the cylinder head bolts are tightened in 3 progressive steps. Tighten them in the proper sequence as follows:
Step 1: 50-55 ft. lbs. (68-75 Nm) Step 2: 60-65 ft. lbs. (81-88 Nm) Step 3: 70-85 ft. lbs. (95-115 Nm) Let me know if I can assist you with anything else.

Posted on Apr 30, 2009

warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

emissionwiz
  • 75817 Answers

SOURCE: spindle nut torque spec on a 2004 F-150

u DON'T torque this!! tighten the nut while spinng the rotor, then back off untiol it is free, then tighten it down until it seats tight, then turn another 1/8" tighter, that is it, any tighter u burn up the the wheel bearings

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is torque spec for 1964 Riviera rear axle pinion nut?


The same book that I hope you used in setting the ring and pinion backlash will give you the ( Rolling Torque). Once the pinion nut is set, a new crush sleeve will be required to correct. This axel will not go around the block if back lash is not correct.

May 10, 2017 | Cars & Trucks

1 Answer

What is the torque spec for a 1978 Ford pinto differential pinion nut?


170 ft.lbs is the minimum; be aware that this differential uses a crush sleeve to set the backlash and the pinion torque is what crushes the crush sleeve. If you don't set the backlash correctly you can grind up your differential gears.
8 Inch Ford Rear End Torque Specifications eHow

Feb 02, 2015 | Ford Cars & Trucks

1 Answer

What are torque specs on 1965 ford 7 and 1/4 inch rear


I have a '68 Motor's manual (goes back to'58) the only rear end specs I can find are for the pinion nut (140 ft. lbs.)
pinion preload: 17-27 in. lbs. w/integral carrier or 22-32 in.lbs. w/ removable carrier. Tightening the carrier bearings isn't so much a torque setting but more or a tightening procedure. Theses specs are done during the rebuild so I wonder if you're asking about the bearing caps or bolts that hold the diff. to the axle housing? I could not find a spec. for bolt torque. Since the bolts that hold it in (if that is what you asking about) are not a bearing adjustment, you can go with a generic torque based on bolt size. Again, I'm not sure what component, or bolts it is you are asking for torque specs on.

Sep 17, 2014 | Cars & Trucks

1 Answer

Can some one tell me the torque spec. on rear pinion nut ?


It depends if you are replacing the pinion seal or fitting up a whole new pinion collapsible spacer. If it just the seal that you are replacing then the tension will be to do the nut up until it is firm. Any over tightening of the nut will further collapse the spacer and over preload the bearings . If you use a new spacer then the tension on the nut is determined by a turning torque on the pinion flange as measured by a spring balance and string. To get it right consult a workshop manual.

Jul 26, 2014 | 1997 Ford F150 Regular Cab

1 Answer

I need the torque specs on a rear axle pinion nut for a 2003 Dodge Ram 2500 4/4 Cummins, Automatic.


The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a "torque to rotate" torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate. To measure this you will need to tighten the nut in small increments then use the torque to rotate wrench to turn the pinion without the carrier/ ring gear installed. Repeat until desired torque is reached.

Jan 29, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

Rear pinion nut torque spec? please if anybody knows.


200 foot pounds should crush the collar and set the pinion in tight to specs.
Good Luck!!!

Sep 21, 2010 | Ford F-350 Cars & Trucks

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

1 Answer

What are the torque specs for the pinion nut and flange bolts on a 1990 ford f350 srw differential? Does anyone have diagrams or pics of how to remove and replace the pinion seal on the same model year...


Most pinion nuts don't have a published torque spec. they are to be tightened until the pinion requires a specified torque to spin with the wheels and brake drums removed. Often times, when a rebuild is not performed, it should be torqued to the same preload as before the work. autozone.com has alot of good repair info and diagrams.

Nov 17, 2009 | 1990 Ford F350

1 Answer

Torque Specifications


1. If you are speaking of the large yoke nut there is no "torque spec" per say, instead it is a rotational preload-

From Ford manual:
Use the special tool to hold the pinion flange while tightening the nut to set the preload.
  • Tighten the nut, rotating the pinion occasionally to ensure the differential pinion bearings are seating correctly. Take frequent differential pinion bearing preload readings by rotating the pinion with a Nm (inch-pound) torque wrench. The final reading must be 0.56 Nm (5 lb-in) more than the initial reading taken during removal.
2. If you are looking for the yoke straps that hold the universal in place to the yoke it is 14ft lb for the 4 bolts.

May 28, 2009 | 2004 Ford Ranger

Not finding what you are looking for?
2003 Ford F250 Super Duty Crew Cab Logo

Related Topics:

355 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...