Question about 2000 Ford Mustang

Open Question

Need to change a door lock cylinder in a 2000 ford mustang

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Jay_from_Ma
  • 99 Answers

SOURCE: 2000 ford mustang warning lights

That sounds like your traction light. Does it have a trac button on the dash? If so, try switching it and see if it helps.

Posted on Dec 16, 2008

Ad
  • 6 Answers

SOURCE: How do I change the turn signal bulb on 2000 Ford Mustang

Actually its easier that what the other guy said. lift your hood, look at the headlight there will be two rods that u can pull on the top of the light where it sits in the frame. pull those and u can then pull your headlight out, that will make it alot easier to get to.

Hope This Helps.

Posted on Sep 15, 2009

  • 3 Answers

SOURCE: Remove door panel on a Ford Van

For a 1999 Ford Econoline 150 (assume the same or very similar), remove triangular plastic cover over mirror assembly by prying straight out, remove plastic door handle cover by prying up from the front side, remove electronic door switches by prying up from back side, remove round plastic cover at bottom rear of door panel. Four screws are now revealed, remove them. Lift door panel straight up, clips are hooks (not snap in). Work door switch assembly out of door panel. Set door panel aside. Reassemble in reverse order.

Posted on Nov 21, 2009

01fordeb
  • 1033 Answers

SOURCE: Door locks on Ford Expedition stuck

Look under your steering wheel right under the dash. There should be a small white strip with 5 numbers. This is your master code for your vehicle. If you bought the car used and they give you a code, they could have made their own code, but the master will override it. If this don't help, the module for the doors may be going bad.

Posted on Jan 05, 2010

  • 5 Answers

SOURCE: 2000 ford mustang front door panel speaker removal

you will have to un screw your door lock. pop off your door handle inside bezel which will reveal a screw to take off. pop off the panel with the power window and mirror switches that will reveal another screw to take off. as soon as you do that the door will have to have all of the push clips popped out by taking either a special claw tool for it or you can use a flat head screw driver at the bottom of the door panel. as soon as you un clip all of the clips you lift up on the door panel to remove it ands that gives you access to the speaker

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a new lock cylinder


You have to remove the Wheel and remove the locking Screw and then you rotate the Cylinder (Pay attention what ANGLE it is ) and then it slides out with the Key in the Ignition

Apr 15, 2013 | 2000 Ford Mustang

1 Answer

Where to find the sensor on the door


On the Ford its part of the door lock assemble you will need to take the panel out to access the door switch,You should make this a hobby of replacing,you will always have this problem

Mar 28, 2012 | 2000 Ford Mustang

1 Answer

My theft light keeps blinking on my 2000 ford mustang will not crank only gave it a boost off and it cut off will not restart


MANUSALLY LOCK BOTH DOORS THEN UNLOCK PASSENGER SIDE FIRST THEN DRIVER SIDE THIS SHOULD RESET THE ANTI THEFT

Aug 02, 2011 | 2000 Ford Mustang

1 Answer

How do i reset the anti theft system ford mustang 2002 gt


The system reset any time the correct ignition key is turned to the run position or the door is locked and unlocked with the key, there is a sensor on the lock cylinder. If this is what you have done then already then the system have problem and you will need the dealer to scan it for fault codes. You may have a defective key transponder sensor in the ignition lock cylinder.

Jan 17, 2011 | Ford Mustang Cars & Trucks

1 Answer

Instructions on how to activate a 2000 ford mustang keychain alarm/remote. I have already had to get a key re-chipped and bought the remote from the Ford dealershi[ and all I got was some hand written and...


Take all key fob put all of them dash or consel get in cars shut door put key in ignition turn ingition on/off 7 times 8th time stop in the on position door lock should cycle on/off push a button on each key for turn ingnition ooff and test.

Aug 04, 2010 | 2000 Ford Mustang

1 Answer

Lost my keys to my 2000 mustang


You should contact a good lock smith,most of thease guys can re programme a new key all you need is to remove the door lock and a new key can be cut from this.Also they will be half the price or more than a dealer.

Mar 08, 2010 | 2000 Ford Mustang

1 Answer

2000 ford mustang 4.6 is coming up with code of bank 2 sensor 1 an changed plugs an 5 an 6 cyl plugs were black but no plugs were wey


ur engine is a v6, the head that has the number 1 cylinder is bank 1, so u need to go to the second head and follow the exhaust line, ull find a sensor there, probabbly has 4 cables looks a lot like a spark plug, thats ur oxygen sensor, that probabbly needs to be replaced.
hope this helps
have fun!

Oct 31, 2009 | 2000 Ford Mustang

1 Answer

How do I change an Ignition on a 1988 Ford Mustang GT Automatic Transmission


Not exactly sure when Ford changed the style. But I think it is this one. First of all do you have the key thet fits the lock cylinder you are changing? If so, put the key in and turn it to the run position. If this is the style I'm thinking about there will be a small hole in the column cover under the lock cylinder. A small allen wrench works fine. Push in with allen wrench and at the same time pull out on lock cylinder. (you may have to turn key alittle one way or the other to release pin.) If you don't have the key for this lock cylinder it will be EXTREMELY difficult to remove. Hope this is helpful .

Mar 22, 2009 | 1988 Ford Mustang

Not finding what you are looking for?
2000 Ford Mustang Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...