Question about 1999 Jeep Cherokee

Open Question

Location of washer pump fuse on 1999 jeep cherokee

Washer pump don"t work

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

picatudo
  • 239 Answers

SOURCE: 1999 windshield washer pump relay

there is no relay is the same fuse for the wipers

Posted on Jan 14, 2009

  • 1596 Answers

SOURCE: 1999 jeep cherokee do you have to remove the fuel pump to replace

The combination Fuel Filter/Fuel Pressure Regulator is located on the fuel pump module. The fuel pump module is located on top of fuel tank.

The filter/regulator may be removed without removing fuel pump module although fuel tank must be removed.

REMOVAL

  1. Remove fuel tank. Refer to Fuel Tank Removal/Installation.
  2. Clean area around filter/regulator.
  3. Disconnect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
  4. Remove retainer clamp from top of filter/regulator. Clamp snaps to tabs on pump module. Discard old clamp.
  5. Pry filter/regulator from top of pump module with 2 screwdrivers. Unit is snapped into module
  6. Discard gasket below filter/regulator.
    1. Before discarding filter/regulator assembly, inspect assembly to verify that O-rings are intact. If the smallest of the two O-rings can not be found on bottom of filter/regulator, it may be necessary to remove it from the fuel inlet passage in fuel pump module.
    INSTALLATION
    1. Clean recessed area in pump module where filter/regulator is to be installed.
    2. Obtain new filter/regulator (two new O-rings should already be installed)
    3. Apply a small amount of clean engine oil to O-rings. Do not install O-rings separately into fuel pump module. They will be damaged when installing filter/regulator.
    4. Install new gasket to top of fuel pump module.
    5. Press new filter/regulator into top of pump module until it snaps into position (a positive click must be heard or felt).
    6. The arrow molded into top of fuel pump module should be pointed towards front of vehicle (12 O'clock position).
    7. Rotate filter/regulator until fuel supply tube (fitting) is pointed towards front of vehicle (12 O'clock position).
    8. Install new retainer clamp (clamp snaps over top of filter/regulator and locks to flanges on pump module).
    9. Connect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
    10. Install fuel tank. Refer to Fuel Tank Removal/Installation.
WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. THIS PRESSURE MUST BE RELEASED BEFORE SERVICING FUEL TANK .

Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool).

The quickest draining procedure involves lowering the fuel tank.

As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure for procedures. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

FUEL TANK REMOVAL
  1. Disconnect negative battery cable at battery.
  2. Release fuel system pressure. Refer to the Fuel System Pressure Release.
  3. Raise and support vehicle.
  4. If Equipped: Remove fuel tank skid plate.
  5. Remove 4 fuel hose shield mounting bolts and remove fuel hose shield from body.
    1. Remove fuel tank fill hose and vent hose clamps at fuel tank filler tube. Remove both hoses at fuel filler tube.
    2. Remove exhaust tailpipe heat shield mounting bolts and remove shield. CAUTION: To protect fuel tank from exhaust heat, this shield must reinstalled after tank installation.
    3. Place a hydraulic jack to bottom of fuel tank. WARNING: PLACE A SHOP TOWEL AROUND FUEL LINES TO CATCH ANY EXCESS FUEL .
      1. Disconnect fuel supply line from fuel extension line near front of fuel tank. Refer to Fuel Tubes/Lines/Hoses and Clamps. Also refer to Quick-Connect Fittings for procedures.
      2. Disconnect EVAP canister vent line near front of tank.
      3. Disconnect fuel pump module electrical connector (pigtail harness) near front of tank. Harness connector is clipped to body.
        1. Remove two fuel tank strap nuts. Position both tank support straps away from tank.
        2. Carefully lower right side of tank while feeding both fuel hoses through access hole in body. Fuel Tank Full And Not Drained Using DRB Scan Tool: To prevent fuel loss through hoses, keep left side of tank higher than right side while lowering. Do not allow hose openings to drop lower than top of tank.
        3. Continue lowering tank until clear of vehicle. Place tank on floor with left side (hose side) higher than right side
          1. Drain tank by removing fuel fill hose at tank. Fuel fill hose is largest of 2 hoses. Insert the drain hose (from an approved gasoline draining station) into hose opening. Drain tank until empty.
          2. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/installation for procedures.
          INSTALLATION
          1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/installation for procedures.
          2. Install fuel fill/vent hoses to tank fittings. To prevent hose from kinking, rotate each hose until index mark on hose is aligned to index tang on fuel tank.
          3. Install hose clamps to hoses. Position clamps between index marks on each hose.
          4. Position fuel tank to hydraulic jack.
          5. Raise tank into position while guiding fuel fill and vent hoses into and through access hole in body.
          6. Continue raising tank until positioned to body.
          7. Attach two fuel tank mounting straps and mounting nuts. Tighten nuts to 10 Nm (90 in. lbs.) torque. Do not over tighten nuts.
          8. Install both fuel hoses to fuel fill tube. Tighten both retaining clamps.
          9. Position fuel hose shield to body. Install and tighten 4 mounting bolts.
          10. Connect fuel pump module pigtail harness electrical connector near front of tank.
          11. Connect fuel pump module supply line near front of tank. Refer to Quick-Connect Fittings for procedures.
          12. Connect EVAP hose near front of tank.
          13. Install exhaust tailpipe heat shield.
          1. Install fuel tank skid plate (if equipped).
          1. Lower vehicle and connect battery cable to battery.

Posted on Feb 08, 2009

  • 154 Answers

SOURCE: LOCATION OF LIGHTER FUSE FOR 1996 JEEP GRAND

If you have the owner's manual look up fuses in the index, good illustration. If you don't, I do. It shows a relay and a 15 amp fuse. Look at the passenger kick panel, pull the cover, and it is #2 fuse (second from the top on the left) The see the relay you may have to pull the panel (two screws and a clip) the relay is the third cavity down, third row from the firewal side.
Let me know if this works for you?

Posted on Apr 03, 2009

  • 29 Answers

SOURCE: 1999 Jeep Cherokee rear window washer

There are two separate washer pumps underneith the washer res. behind the front driver quarter panel. The exact pumps are hard to find. I have the same prob with my 99, but both are out. I had a 98 that the front worked but not rear. I had to get a "universal" washer pump. I'm still trying to find a factory replacement for this one before I do that. No luck so far.

Posted on Apr 26, 2009

  • 6 Answers

SOURCE: Fuse diagram for the 2001 jeep cherokee sport 4.0L needed

Believe the AC compressor Relay is located on the left side of the Fuse block inside the passenger kick panel. Exact location is in your owners manual.

Fuel pump relay is inside of the Engine Fuse block under the hood on the passenger side. Locations are written inside of the lid.

Posted on May 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my washer pump fuse at,my pump doestnt work


Hi there,

The washer pump you seek is located in the washer assembly in the fender well of the vehicle.

Good luck!

Jan 11, 2011 | 1999 Jeep Cherokee

2 Answers

Hi...I have a 1999 Jeep cherokee Sport. The windshield washer quit..dont know if it is a clogged line or a pump. Not hearing the pump when I activate. Also lines appear to be hidden.


This is most likely due to the washer pump going out. I just replaced mine on my 2000 cherokee. There is a front and back pump which is located under the drivers side fender. You will have to remove the plastic corner bumper to get access to the pumps. This is an easy job to do yourself. Dont forget to have something ready to drain the fluid into when you remove the pump from the washer tank. The front pump is located below the rear pump.

Dec 01, 2010 | 1999 Jeep Cherokee

1 Answer

Windshield washer doesn't work. The fluid tank is full. I don't hear the pump trying to run. Could it be the pump or pump motor? I can't locate it.


it may be a blown fuse, check the fuses or it could be the pump motor, the pump motor is at the bottom of the fluid tank,also check the wiring.....hope this helps.....cheers

Aug 07, 2010 | 1999 Jeep Cherokee

1 Answer

My 2005 Jeep Grand Cherokee's windshield washer is not working.


Check power at the pump motors. You may not see a fuse because some run off a circuit breaker. If all else fails, a bit "backyard" but you likely could break out the washer pumps from the system and make a simple push button on the dash to operate them.

Jul 08, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

2005 jeep grand cherokee


The washer pump is located on the washer bottle. Must check for power at pump when applying switch if no power (12 volts) check fuse or curcuit. If it has power replace pump. Also: if pump is operational check hoses for resteictions.

Jun 13, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Washer pump is not working 99 Jeep cherokee


I think that on the fuse pannel it should say which fuse goes to what. If the fuse is still good, try making sure the connections are tight. If they are replace the pump.


Brandon Bird

Jan 18, 2009 | 1999 Jeep Cherokee

2 Answers

What fuse controls the windshield washer pump? on a 2001 Jeep Che


usually it's in the washer bottle which is usually in the fender well, ahrd to get to.
The fuse that controls it should be listed in your owners manual. Usually a 10 amp fuse in the fuse panel inside the car usually on the instrument panel somewhere.

Jan 09, 2009 | 2001 Jeep Grand Cherokee

1 Answer

1999 windshield washer pump relay


there is no relay is the same fuse for the wipers

Nov 29, 2008 | 1999 Jeep Cherokee

1 Answer

Front widshield washer fromm 1999 Cherokee doesn't work


the same reservoir is used for both ...it uses separate pump motors.....if the wipers are working the fuse for the washer pump is good...check the power and ground for the pump...

Nov 01, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
1999 Jeep Cherokee Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...