Question about Isuzu Cars & Trucks

Open Question

Isuzu kb320 6vd1 camshaft timing marks after removing all the camshfts

After removing the camshaft while touqing the head,im now failing to replace them correctly

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MrScary66613
  • 1990 Answers

SOURCE: TDC in Haynes Manual- Isuzu Rodeo TF 1991

No. 4 to Top Dead Center is Correct.

Posted on Jan 03, 2009

honeymokey
  • 3113 Answers

SOURCE: 2000 isuzu trooper 3.2 v-6 dohc camshaft timing

It's more to it than aligning the marks since the cam pulleys turn about three times or more to one turn of the camshaft on this engine. You need to find someone that is experienced on this vehicle.

Posted on May 13, 2009

  • 1 Answer

SOURCE: TIMING MARKS CAMBELT REPLACEMENT FOR CL-T CHARADE, PLEASE

Hi Cas,

1) timing belt - see the small dot on tooted crank (small) pulley and match this with a notch ^ on engine body. Align the 'F' on overhead camshaft front pulley with lower crank shaft (small pullet). You should also alight the top pulley with a ^ on right side of big pulley when facing engine from front

In case of diesel pump:
2) cam belt - alight the dot mark on small camshaft pulley with notch ^ on tappet cover. Move and hold pump pulley and alight it with dot on this pulley to dot mark on plate to which pump is bolted.

Regards,

Gulfraz, Karachi, Pakistan

Posted on Jan 25, 2010

  • 1757 Answers

SOURCE: isuzu trooper 2002 RLV engine. camshaft timing

Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams and Photos with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams, instructions and photo's for use.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2002/make/isuzu/model/trooper/2002_isuzu_trooper_timing_belt_diagram_marks.htm

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ok 1990 geo storm 1,6 litre dohc replaced water pump replaced 3 valves replaced head gaskets replaced timing belt car wont start any ideas?


90 Storm, must be in Canada, 1,6 (the comma tells me this)
the storm is a:
The car is really an Isuzu Impulse minus some of that car's more expensive features.
my guess is you drove the this 4EX1 engine until the cam belt slipped. yes> if yes you bent valves.????????????
so does compression exceed 150psi on all 4 cylinders now?
we use the cylinder leak down test in all DOHC .
if not , back to the drawing board.
if yes, the we check spark next, then try test fuel.
when did the engine last run , last week,month , year,?
who did your valves, a real machine shop or kid down the street.
a read shop pressure tests the head ,and warp checks it and
then makes sure the valves are ready for long service.
are the head bolts at 58 ft/lbs
did you use sealant on the 3 cap caps, per the FSM book.
if not , top end oiling will fail. and cams wrecked.

the 1.6l DOHC has no HLA's
the lash on valves must be checked, and this is corrected with SHIMS.

a pro machine shop does the for you,did they:?
when rebuilding engines, its best to read the factory service manual first. FSM so you know the special steps just for this engine.
ISUZU engine it is.



quote.
1.6L Twin Camshaft Engine
  1. Disconnect the negative battery cable.
  2. Remove the cylinder head or valve cover.
  3. Position the No. 1 cylinder at TDC on its compression stroke.
The notch on the crankshaft pulley should align with the 0 degrees mark on the timing gear case. Make sure the rocker arms on the No. 1 cylinder are loose and the rockers on the No. 4 cylinder are tight. If not, turn the crankshaft one complete revolution and align the marks again.
  1. Using a feeler gauge, measure the clearance between the cam lobe and the selective shim on the intake and exhaust valves on the No. 1 cylinder, then the intake valves on the No. 2 cylinder and the exhaust valves on the No. 3 cylinder. Note readings.
  2. Rotate the crankshaft 360 degrees. Using a feeler gauge, measure the clearance between the cam lobe and the selective shim on the intake and exhaust valves on the No. 4 cylinder, then the intake valves on the No. 3 cylinder and the exhaust valves on the No. 2 cylinder. Note readings.
  3. The valve clearance obtained on the exhaust valves should be between 0.008-0.012 in. (0.20-0.30mm). If not, replace the selective shim by turning the camshaft lobe downward and installing tool J-38413-2 or J-38413-3 (valve lash spring spacer) between the camshaft journal and the cam lobe next to the selective shim. Turn cam lobe upward and remove the selective shim. Install new shim using the selective shim chart.
The rear camshaft bearing caps must be removed to remove the selective shim.
  1. The valve clearance obtained on the intake valves should be between 0.004-0.008 in. (0.10-0.20mm). If not, replace the selective shim by turning the camshaft lobe downward and installing tool J-38413-2 or J-38413-3 between the camshaft journal and the cam lobe next to the selective shim. Turn cam lobe upward and remove the selective shim. Install new shim using the selective shim chart.
  2. When the adjustment is completed, install the cylinder head covers and connect the battery negative cable. Start the engine and check for leaks.
end fsm quote.

see those 2 marks, and crank must be at TDC. mark first.

26196190-t50uqibptsz0ry0el5zdiz1k-1-0.jpg

May 16, 2016 | Geo Cars & Trucks

1 Answer

Setting timing marks


Google Image this: Camshft timing marks for a (you provided no engine info)______ Liter engine. You should find many diagrams.

Oct 11, 2012 | 1991 Isuzu Pickup

1 Answer

Timing diagram for both belts


always timing mark at the rear of cam shaft by useing special tools . for crankshaft on gear box housing there is plastic cover remove you can see mark on flywheel . there mark for timing belt tensioner try to keep not too mach tight ( you can press timing belt with your fn). for 1.8 over head camshft there is mark on camshat and camshaft bracket keep two point together for each camsh.then but the chain . for 1.2 engine use special tools rear camsh.with mark on fly wheel

Jun 19, 2011 | Volkswagen Camper Cars & Trucks

1 Answer

What are the timing marks for a 2000 vw beetle 2.0litre


camshft pulley lines up with notch on head at approx 11o'clock crankshaft pulley marks at 12 o'clock
also crnkshaft marks at flywheel end remove plug on top of bell housing and pointer should line up with "0" mark on flywheel
engine should be cold when fitting new belt

Apr 26, 2010 | 2000 Volkswagen Beetle

1 Answer

Need the timing marks for 99 ford contour


There are no marks. You need to remove #1 spark plug. Bring the piston up on TDC (all the way up). Then remove valve cover. On the drivers side of the camshafts you will see a slot ground into the ends. The slots are off center of the camshft. There is a tool to fit into the slots tieing both cams at the same time. Once the tool is installed and the #1 piston was up before you locked the cams you can remove the T-belt for replacement & water pump replacement.

Sep 08, 2009 | 1999 Ford Contour

2 Answers

I can't find the timing marks of an isuzu engine 4hf1


Timing is aligned with bolts through holes in the drive wheels under the timing cover and a mark on the crankshaft remove the timing cover turn the crankshaft until the mark is at the top. the engine has treaded holes behind the drive wheel's get bolts(12 or 13mm head metric tread 4 or more ins long) push them through the holes in the wheels and screw to the engine this is alingment in an isuzu engine

Jun 15, 2009 | 1995 Isuzu Pickup

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

1 Answer

Time marking for camshafts


7e745eb.jpg this is for all UBS,UES,TF V6 ENGINES

Nov 11, 2008 | 1999 Isuzu VehiCROSS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...