Question about 2004 Dodge Caravan
Had a starter that worked fine. Brought it to the garage to have the windshield replaced. when I got it back, the remote starter no longer worked.
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: remote keyless entry
“CUSTOMER LEARN” MODE
This feature is only available on domestic vehicles or those which have a U.S. country code designator. This procedure requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, Sentry Key programming will require the use of a scan tool.
The steps required to program Sentry Keys with two valid Sentry Keys follows:
1. Obtain the blank Sentry Key(s) that need to be programmed. Cut the keys to match the ignition lock cylinder mechanical key codes. 2. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the ON position. 3. After the ignition switch has been in the ON position for longer than three seconds, but no more than fifteen seconds, cycle the ignition switch back to the OFF position. Replace the first valid Sentry Key in the ignition lock cylinder with the second valid Sentry Key and turn the ignition switch back to the ON position. The second valid Sentry Key must be inserted within 15 seconds of removing the first valid Sentry key. 4. About ten seconds after the completion of Step #3 , the indicator light will start to flash and a single audible chime tone will sound to indicate that the system has entered the "Customer Learn" programming mode. 5. Within sixty seconds of entering the "Customer Learn" programming mode, turn the ignition switch to the OFF position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the ON position. 6. About ten seconds after the completion of Step #5 , a single audible chime tone will sound and the indicator light will stop flashing and stay on solid for three seconds and then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKREES will immediately exit the "Customer Learn" programming mode and the vehicle may be started using the newly programmed Sentry Key.
NOTE: The Remote Keyless Entry (RKE) Transmitter will also be programmed during this procedure. These steps must be completed in their entirety for each additional Sentry Key to be programmed. If any of the above steps are not completed in the given sequence, or within the allotted time, the SKREES will exit the "Customer Learn" programming mode and the programming will be unsuccessful. The SKREES will also automatically exit the "Customer Learn" programming mode if:
NOTE: If you attempt to start the vehicle while in “Customer Learn” mode (LED flashing), the vehicle will behave as though an invalid key is being used (i.e. the engine will stall after two (2) seconds of running). No faults will be logged.
NOTE: Once a Sentry Key has been programmed to a particular vehicle, it cannot be used on any other vehicle.
Posted on Aug 05, 2008
SOURCE: starter for dodge caravan 2000
DISCONNECT THE BATTERY, JACK UP AND SUPPORT YOUR CARAVAN. LYING ON YOUR BACK LOCATE THE STARTER WHICH IS ATTACHED TO THE ENGINE THROUGH THE BELL HOUSING .THERE ARE TWO 15 MILIMETER BOLTS THAT HOLDS THE STARTER ON . AFTER BREAKING THE BOLTS A 15MM WRENCH WOULD BE USEFUL.
Posted on May 30, 2008
I recently had the same issue, but my airbag warning lights also turned on. If this is the case, it might be the clockspring. There is a recall on clocksprings for Caravans 1998 - 2000 I believe. I got it replaced for free in the dealership. Enter your VIN in this site and it will tell you if you are covered in the free replacement warranty.
Hope this helps.
Posted on Mar 06, 2009
with most front wheel drives you must remove the passenger tire and reach through to the starter bolt with an extension and if I remember write with a 15 mm socket you can reach through and take out the bolt
Posted on Jun 20, 2009
Tips for a great answer:
May 24, 2015 | 2005 Dodge Caravan
Dec 15, 2012 | 2008 Dodge Grand Caravan
Oct 05, 2009 | 1992 Dodge Caravan
Sep 08, 2009 | Dodge Caravan Cars & Trucks
Apr 03, 2009 | 2000 Dodge Caravan
Dec 13, 2008 | 1998 Dodge Caravan
Aug 03, 2008 | 2001 Dodge Caravan
Mar 05, 2017 | 2004 Dodge Caravan
104 people viewed this question
Usually answered in minutes!