Question about 2007 Mazda MAZDA6

Open Question

Replace bulb in high brake light on 2007 Mazda 6

Posted by Anonymous on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: How do you replace the head light bulb on a 2004 Mazda 6?

This is a problem - I had both drivers and passenger bulbs go on me and came at it through the wheel arch. The method is the same for both sides.

Equipment needed

Short handled Phillips screwdriver
2 x Latex gloves - to save scratches and dirty hands

Use 1 glove to save your hands
Lift bonnet to get as much light on the job as you can
Turn wheel in so you can get at wheel arch liner unmolested
Remove the plastic nuts – don’t loose them
Peel back liner – you can now see the back of the lens cover
You may need a torch, I did
Turn cover and pull it away – you can now see back of bulb
Remove clip, noting the way to the comes out, there is a notch on the base of the bulb and the replacement must go in that way

Use clean glove to handle bulb, keep to base of bulb and not the glass

Replace is the reverse of the above

Allow 30-45 mins first time

Posted on Nov 17, 2008

  • 1986 Answers

SOURCE: 05 Mazda 6 I need to replace the headlights

Behind the head lamp you'll see a circular cap with some fins on it. Turn it counter clockwise and then it should come out exposing the back of the bulb. Then you will need to push in and up on an angle to release the metal spring clip that holds the bulb in place. Then you can disconnect the harness to the back of the bulb and then remove the bulb. Do not touch the glass of the bulb when putting in the new one as that will cause the bulb to catastrophically fail

Posted on Oct 28, 2009

SOURCE: how to replace brake light bulb?

If similar to 2002 MPV, you detach the whole side light module, then pop out the bulb-socket, then you can replace the bulb. You need a philips screwdriver, medium size. Open the back hatch. Remove the two screws on the inside edge of the light-assembly. Now pull the whole assembly *sideways* not back - it is held by two detent-pins that face out. You can swing it out a bit and then carefully lever it at top or bottom edge. Lower the assembly face-down, you can see three bulb-sockets. They can be turned a part-turn, I think counter-clockwise, then they pop out. Replace bulb(s), re-insert socket, push assembly back onto pins, replace screws. Just did this for brake/tail light 10 minutes ago.

Posted on Jan 28, 2010

  • 121 Answers

SOURCE: How to: Replace high-mount brake bulbs Mazda MPV 2002

It will be either on the outside with 2 small screws or more likely you need to remove a trim/cover of the top headliner area... If still in doubt goto or phone the dealer and just ask the parts dept person to show it to you...

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How much should it cost to replace a Toyota Avalon 2007 LED brake light?

High there... Patrick Cummings,

Not that mush!

Somewhere 'twix $14 & $21...
according to ROCKAUTO.COM...

(see below) 2007 TOYOTA AVALON 3 5L V6 Brake Light Bulb RockAuto

Check out the pricy one at ..
More Information for DORMAN 7443RHP

Aug 18, 2016 | 2007 Toyota Avalon

1 Answer

How to change tail light

Open the trunk and you will see screw underneath the carpet.remove the screw and push the light out.remove the burn bulb and replace with same model # . If the bulb is dual (5W-15W) will have different high on the locking pins. place the light back and tight slightly.DO NOT OVER TIGHT, WILL BRAKE THE KIGHT

Apr 15, 2014 | 2012 Mazda 3 i Touring 4dr Hatchback 2.0L...

2 Answers

My brake lights and rear blinkers are not working. I have replaced the bulbs in both brake lights. What next?

most blinkers uses relays, and when they flashes fast one light is out, but you replaced your burnt bulb might be a bad relay.

Sep 17, 2012 | 2007 Hummer H2 SUT

1 Answer

2007 Mazda 6 headlight

Then the light has a leak and moisture is getting in.

Jul 24, 2012 | 2007 Mazda 6

1 Answer

2007 GMC Sierra 1500 My high brake light not working,checked bulbs and fuses,there good.What should i look for now?

check for power to the brake assembly. the socket board in high mounts are prone to have problems. if you have power to the socket board then it needs replaced.

Apr 10, 2011 | 2007 GMC Sierra 1500

1 Answer

How to: Replace high-mount brake bulbs Mazda MPV 2002

It will be either on the outside with 2 small screws or more likely you need to remove a trim/cover of the top headliner area... If still in doubt goto or phone the dealer and just ask the parts dept person to show it to you...

Jan 28, 2010 | 2002 Mazda MPV

1 Answer

Brake lights not working & can't find any bad fuses,& brake light switch replaced

why was brake light switch replaced? you need to check things before replacement. is the brake light switch getting power? if not the fuse is blown. if it is getting power, is power going out? if so, check for power at the bulbs, if no power find out why, if the bulbs do have power, they are not getting ground. the ground wire is in trunk, I really dont know exact location. may be near high mounted brake light.

Oct 21, 2009 | 1999 Mazda 626

2 Answers

Mazda 626 1991 back brake ligths not working

Is the fuse for the brake lights OK?
Check for power to the brake light switch at the brake pedal and for power coming from it with brake pedal depressed.

Sep 06, 2009 | 1991 Mazda 626

2 Answers

94 Mazda B3000

Check the brake light switch located under the dash, and is energized by depressing the brake pedal.

Jan 28, 2009 | Mazda Cars & Trucks

Not finding what you are looking for?
2007 Mazda MAZDA6 Logo

Related Topics:

364 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides