Question about 2005 Mitsubishi Endeavor

Open Question

How to change thermostat on a 2005 mitsubishi endeavor

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Timing Belt for 2004 Mitsubishi Endeavor

Yes, I would replace it according to the owner's manual. Could be very expensive if it breaks.

Charlie

Posted on May 31, 2009

Ad
  • 3 Answers

SOURCE: Cabin Air Filter - 2004 Mitsubishi Endeavor (Where?)

IT IS IN BEHIND THE GLOVE COMPARTMENT YOU HAVE TO TAKE IT OUT BY UNSREWING AND START FROM YOUR RIGHT SIDE

Posted on Jun 10, 2009

  • 1 Answer

SOURCE: trying to change spark plugs

THEIR ARE ABOUT 9 BOLT TO REMOVE THAT SUPPORT THE INTAKE. 2 ARE IN THE REAR IN THE CENTER OF THE SUPPORT BRACKET THE 5 THAT ANCHOR THE INTAKE ITSELF AND 2 UNDER THE INTAKE THROTTLE BODY. ( 12MM) 3 HOSES ON TOP OF THE INTAKE TO REMOVE AND 1 SENSOR TO UNPLUG OR UNBOLT (8MM)THE ONE ON TOP OF THE INTAKE (TOP LEFT REAR). THIS WILL GIVE YOU ACCESS TO THE REAR PLUGS.
REMOVE THE SENSORS BRACKET OR HOLDER ( ON THE LEFT JUST LIFT UP TO REMOVE) AND SWING THE INTAKE TO THE RIGHT. UNPLUG THE PLUG MODULE THEN UNBOLT THEM (10MM).

Posted on Aug 29, 2009

  • 836 Answers

SOURCE: low tire light is blinking on a 2005 mitsubishi

You have low air pressure in a tire, check them all including the spare which may have a sensor installed.

Posted on Jan 14, 2011

  • 14036 Answers

SOURCE: My spark plugs in my

YOU NEED LONG SPARK PLUG SOCKET. NEED A 3/8 INCH RATCHET WRENCH.YOU NEED EXTENSION.YOU NEED SPARK GAUGE YOU NEED A TORQUE WRENCH. NOT MANDATORY JUST DONT OVER TIGHTEN SPARK PLUGS STRIP ALUMINUM THREADS WAIT UNTIL ENGINE COOL TO KEEP FROM WARPING THE HEADS. SPARK PLUGS LOCATION ON TOP OF CYLINDER HEADS.TO GET TO SPARK PLUGS THE COILS ON TOP EACH SPARK PLUG.HAS TO BE REMOVED BY REMOVING SMALL SCREW.THAT HOLD COILS DOWN.AND CHANGE ONE SPARK PLUG AT A TIME SO YOU WONT GET THEM MIXED UP.GAP PLUGS AT 0.028 - 0.031

Posted on Jan 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a way to reset keyless entry for 04 endeavor?


Search Results

    2004 Mitsubishi Endeavor Key Fob Remote Programming ...

    blog.keylessentryremotefob.com/.../04/2004-mitsubishi-endeavor-key-fo...
    Apr 25, 2013 - 2004 Mitsubishi Endeavor Key Fob Remote Programming Instructions ... you might have visit us at Keylessentryremotefob.com You can also ...

    Mitsubishi - Free Keyless Remote Fob Entry programming .

    How To Replace Mitsubishi Endeavor Key Fob Battery 2004 ...

    ? 2:04
    www.youtube.com/watch?v=yeQRdre7O0Q
    Oct 31, 2014 - Uploaded by Keyless Entry Remote Inc
    ... will show you How To Replace Mitsubishi Endeavor Key Fob Battery 2004 2005 To Order This Remote ...

Nov 01, 2015 | Cars & Trucks

1 Answer

What gas octane level is optimal for my Mitsubishi 2005 Endeavor?


87 Octane is what it calls for, any higher and you will have cold start problems.

Oct 18, 2012 | 2005 Mitsubishi Endeavor

1 Answer

Does the Knecht OC205 oil filter fit for my 2005 Mitsubishi Endeavor?


I have no way to look this up. Use the one that the parts book specifies.

Oct 18, 2012 | 2005 Mitsubishi Endeavor

1 Answer

Fuse panel diagram for 2005 mitsubishi endeavor


It is usually on the fuse box cover. If that's not readable look in owners manual under fuses and it should show you the correct amperage for each fuse and its place in the panel or box.

Mar 18, 2012 | 2005 Mitsubishi Endeavor

1 Answer

My 2005 mitsubishi endeavor has a wrench light on the display


I have an '06 endeavor and the wrench indicates it's time for an oil change.The computerized service log(for lack of a better phrase)is set for 3000 miles after each oil change which activates the wrench light.It is reset by myself or the mechanic after each service. I HOPE THAT HELPS!

Aug 30, 2011 | 2006 Mitsubishi Endeavor

1 Answer

My Mitsubishi Endeavor (2005) has run 60000 miles. I am going to change Timing Belt. Is Water Pump actuated by the Timing Belt ? So does it make sense to change the Water Pump at the same time? Thanks in...


Its a rule of the thumb that when ever you do a timing belt yopu also change
  1. the crankshaft seals
  2. cam seals
  3. water pump
  4. tensioner pulley(included in the timing kit)
It will just save from paying someone just to pull it apart and do it all over.To reach the timing belt/chain all these will have to be pulled apart so why not change it so it lasta you another 100k's

Aug 08, 2011 | 2005 Mitsubishi Endeavor

1 Answer

Low tire light is blinking on a 2005 mitsubishi endeavor


You have low air pressure in a tire, check them all including the spare which may have a sensor installed.

Jan 14, 2011 | 2005 Mitsubishi Endeavor

1 Answer

2005 Endeavor 100,000 mile service


no not at all, keep what you are doing your doing something right to have a car last that long!!!

May 19, 2009 | 2005 Mitsubishi Endeavor

Not finding what you are looking for?
2005 Mitsubishi Endeavor Logo

Related Topics:

444 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...