Question about Cars & Trucks

1 Answer

Dont know what to connect the red wire to from the headlight assembly replacement

Dont know where to connect the red wire from headlights assembly in 1992 mercedes 400e

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 34,188 Answers

If you have daytime running lights, there is a red wire that connects to what M-B calls the daytime driving lamp control unit. The red wire comes from the terminal block (probably under the hood)

Posted on Dec 01, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: headlight assembly

you will have to remove the front bumper cover to get to 2 bolts and also the grille to get another bolt off also there are are a total of 5 bolts that hold it in. be careful taking it out as you can crack the mounting brackets for the assembly just be patiece it will come out.

Posted on Dec 09, 2008

  • 12 Answers

SOURCE: How do I replace my 2003 Acura TL passenger headlight assembly?

You will have to remove the front bumper to get to the bolts that hold the head light on
I would not recommend you try this unless you have some experience with this type of work

Posted on Mar 13, 2009

crayzeetrayn
  • 837 Answers

SOURCE: REPLACE HEADLIGHT ASSEMBLY IN 2000 LINCOLN TOWNCAR

Open the hood and make sure the car and the lights are off.
Remove the plastic protective cover.There are 3 knobs,turn halfway and pull.Put aside and out of the way.
Remove the three pins that are holding the light assembly in place.These are flat rods with a little bend at the end.
Twist and un-plug the lights,now you can remove the whole lens.
The light bulbs can also be removed and replaced from this point.
Make sure all the bulbs are working before you put it back together.

Posted on Mar 13, 2009

  • 7 Answers

SOURCE: how to replace passenger side headlight assembly on 2001 BMW 325i

The E46 2001 325i headlight assembly is held down by 4 bolts. Question is where they are and how to get to them. The 4 bolts require a 10mm wrench.

There are two bolts on top of the headlight assembly. And two more near the back of the assembly, near the area where you would change a headlight bulb.

There is just one more trick to this. Please refer to this trim: http://e46fanatics.com/howto/howtodetail.php?howto_id=24

This trim hooks on to the side fender, just under the turn signal. You have to unhook this.

Then the entire headlight assembly (including the turn signal) can be slided out together.

Posted on Apr 12, 2009

  • 1 Answer

SOURCE: Headlight repair on 2003 Mercedes Benz E320

how do you change left low beam bulb on 2003 mercedes e320

Posted on Jan 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Replace headlight bulb


  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
  27. PLS VOTE ME
BMW e46 HID Headlight Replace
replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-0.jpg

replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 23, 2012 | 2000 GMC Denali

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

1 Answer

How do you replace the headlight bulb on a 2005 Dodge magnum ?


1) pop hood
2) Look at the back of headlight assembly, if you cannot get to the bulb wiring you are going to have to remove assembly
3) remove assembley and disconnect headlight wiring
4)turn bulb retainer counterclockwise and remove bad bulb and install new
5)if you can reach the bulb wiring without taking out headlight assembly all the better you dont have to do step 4

Mar 09, 2011 | Dodge Magnum Cars & Trucks

1 Answer

Can you help me change my headlight assembley? i have a 97 200sx SE


1.) Pop the hood to your Nissan. The headlight assemblies are only accessible from the engine compartment.

2.) Clear the area behind the bulb you are replacing. If you are replacing the passenger side bulb, you will need to remove the radiator overflow bottle. The bottle will unhook from its connective tube by pulling it toward the front of the car and up from the ground. If you are replacing the driver's side bulb, you may need to remove the battery. You will do this by unscrewing the positive (red) and negative (black) terminals that connect the battery to the engine, and then lifting the battery straight out of its housing.
3.) Remove the electrical connection on the back of each headlight assembly. This will be a bundle of wires with a wide plug sticking into the back of the assembly.
4.) Unlatch the plastic clip holding the headlight assembly case in place.
5.) Pry the small metal clip holding the bulb using your fingers or a screwdriver. Be careful not to bend, break or damage the clip or the bulb.
6.) Insert the replacement bulb into the headlight socket and reattach the metal clip that holds the bulb in place.
7.) Relatch the plastic clip holding the headlight assembly case in place.
8.) Reconnect the electrical connection to the back of the headlight assembly.
9.) Replace the radiator overflow bottle or the battery, depending on which bulb you replaced.

Mar 02, 2011 | 1997 Nissan 200SX

2 Answers

How do you remove the headlights off a Pontiac grand am 2004


Lighting Headlight, Side Marker, Park & Turn Signal Assembly Removal & Installation To Remove:
  1. Open the hood.
  2. Remove the front air deflector.
  3. Apply light pressure to the headlight lens to hold the headlight in place while disconnecting the retainers.
  4. Lift up the headlight retainers to release the housing.
  5. Remove the headlight assembly, pulling straight forward from the headlight mounting panel. NOTE: Note the location and position of the adjuster retainers and locator tab.
  6. Disconnect the wiring harness from the headlight assembly.
  7. Rotate the bulb(s)/socket(s) as needed counterclockwise to release.
  8. Remove the bulb(s)/socket(s) from the headlight assembly.
To Install:
  1. Install the replacement bulb(s)/socket(s) to the headlight assembly rotating clockwise until fully seated.
  2. Connect the wiring harness to the headlight assembly.
  3. Position the headlight assembly to the mounting panel.
  4. Apply light pressure to the headlight assembly lens to hold the assembly in place while installing the retainers.
  5. Align the headlight assembly retainers and slide them over the assembly mounting tabs
  6. Install the front air deflector.
  7. Close the hood.
prev.gif next.gif

Feb 02, 2011 | 2004 Pontiac Grand Am

2 Answers

My kia rondo, driving ligths dont work , i have brigths, dimms, did check all fuses inside and engine


ur head lights are blown out but ur brights will still be good for a min but ya need to replace head lights positive

Jan 14, 2010 | 2007 Kia Rondo LX V6

2 Answers

How do I replace a 2006 Beetle Headlight bulb?


Under the hood you on the back side of the headlight assembly there is a a small release lever with a lock. Push the lock in and rotate the release lever. Push the headlight assembly out so you can have access to the wiring plug. Disconnect the wiring plug and completely remove the headlight assembly. Now on the back of the headlight assembly is a spring clip and a small screw. Remove the small philips head screw and release the spring clip.

Jun 05, 2009 | 2006 Volkswagen New Beetle

6 Answers

How to replace headlights on 2000 Jeep Grand Cherokee


One long bolt at the top - requires a 7mm socket to remove the bolt. The light housing will pry out with a screw driver. There are three ball and socket type connectors that hold the housing in and I just pryed off the plastic housing carefully and "balls" pop out of the sockets. Finally, I was replacing the faded plastic housing and it came with a new wiring harness. It's impossible to reach the connector to use the new wiring harness that comes with the new plastic light housing. So just use the existing wiring harness with the new light assembly.

Nov 25, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...