Question about Cars & Trucks

1 Answer

1998 Ford windstar. No heat. But over heating. Changd themostat. Now hissing n still over heatin. Flushd it too

Posted by on

1 Answer

Bad Head Gasket--- is my guess

Posted on Dec 01, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Ford windstar 2001

Replace the heater actuator switch it is not allowing the door to open, Ours did the same thing so I relaced it . it cost 90.00 from ford

Posted on Nov 02, 2008

alicantecoli
  • 22156 Answers

SOURCE: change oxygen sensor 2001 ford windstar

fist unclip wire,then unscrew it with a 28mm spanner ,fitting procedure is the reverse .It turns anticlockwise to unscrew and clockwise to screw up ,torque setting is a grunt and two scuffed knuckles and max of 3 swear words

Posted on Jan 01, 2009

  • 1 Answer

SOURCE: i have a 2000 ford windstar no heat still

My 99 windstar did this too. It was the blend door that the actuator motor goes into was broke. When you pull the actuator out look into the hole and see if you see a d shape piece coming out of the box if it is not d shape it is broke check out this site great photos

Posted on Feb 28, 2009

  • 4 Answers

SOURCE: 1999 Ford Windstar 3.8 no heat

If you have a knock or clicking noise behind the radio, it is the blend motor. The blend door is spring loaded and the gears in the blend motor are "stripped". The door is spring loaded so that the door is closed to the heater core. About 2 hours to replace and a lot of bending and stretching. You don't have to remove the dash, but all of the trim, radio, and controls will need to come out.

Posted on Mar 01, 2009

  • 221 Answers

SOURCE: 1998 cavalier heats up when idleing. Fan comes on but still heats

Hello senior, whenever the coolant system is opened up there's a possibility you could get air in your system, only way to get it out is by using the bleeder valve, check the coolant temperature sensor it may not be working properly, it tell's the cooling fan when to kick on and off, the condition of the drive belt is also another factor, along with the tensioner and tensioner pulley. it sounds like a problem with the water pump, the cooling fan, or air in your cooling system, to get a good inspection of the water pump fin's you have to remove it.

Posted on Apr 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 96 windstar and when i turn the heat on the a/c compressor starts up. how can i disconnect the compressor or fix the problem?


In some heat settings the A/C compressor will run to remove moisture from the cabin. There is a connector on the a/c compressor if you want to disconnect it.

Nov 13, 2012 | 1998 Ford Windstar

1 Answer

How do you loosen seized original oxygen sensors in a 1998 Ford Windstar?


use a torch to heat up the joint where it joins exhaust- use box end wrench and mallet- tighten a little first then loosen after heating

May 15, 2011 | 1998 Ford Windstar

1 Answer

I have a 98 Ford windstar 2.8 litter. v6 the dash tempature goes to where it suppose to be but when i turn on teh heat I have no heat, just cold air. Is this a cuse of teh thermastat staying open all teh...


no the thermostat must be working or your engine would not heat up, check to see if your heater hoses are hot if only one is hot you need a heater core, but check your coolent level if the van gets low on coolent it will not let any get to the heater thehope engine keeps it all to keep the engine cool....hope this helps

Nov 13, 2010 | 1998 Ford Windstar

1 Answer

Heat & a/c stopped working wont blow any air fuse not blown bought new blower motor connected it and it still wont work 1998 ford windstar van


Check the blower motor relay next to the blower motor,it could be a blower module,but it is the problem.

Apr 16, 2010 | 1998 Ford Windstar

1 Answer

HEAT IN MY 98 FORD WINDSTAR NOT WORKING. AND DISCONNECTED WHAT COULD BE THE PROBLEM? HOW MUCH TO FIX?


maybe the actuator behind the radio that controls the hot and cold air ..$50 part

Mar 05, 2010 | 1998 Ford Windstar

1 Answer

Heat and AC vent problem.


most likley you have a vaccume leak somewhere but also the linkage to the door that that directs the air flow may be in a bind. another possability is the hvac controlls. hope this helps

Jun 08, 2009 | 1998 Ford Windstar

2 Answers

No heat


How about the thermstat

Feb 06, 2009 | 1998 Ford Escort

1 Answer

No heat - ac stays on blowing through defrost vents


If you have the heater directed to the windshield, the AC will turn on. Move the control away from defrost.

Feb 01, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...