Question about 1990 Oldsmobile Ninety Eight

Open Question

Need to replace turn signal lever

How do you remove the steering column cover to access?

Posted by on

6 Suggested Answers

  • 14 Answers

SOURCE: 1995 Oldsmobile Cutlass Ciera turn signal problem

the sswitch is in the steering wheel you must remove the steering wheel being carful to disconnect the airbags in the proper procedure so it wont go off and, the switch will be behind there it is part of the multifunction switch.

Posted on Feb 28, 2009

  • 1 Answer

SOURCE: I need to locate and replace the multi function switch

My turn signal flasher was located to the right of the ash tray, I looked around the column for HOURS and it wasn't there... I also have an 93 oldsmobile cutlass ciera, it drove me crazy because the manual wasn't correct.

Posted on Mar 22, 2009

  • 23 Answers

SOURCE: turn signal/wiper lever broke of in column how do

sorry to say this you will have to take the steering wheel off to get to the turn singnal switch. caution with air bag

Posted on Jul 26, 2009

  • 67 Answers

SOURCE: I have replaced the turn signal switch on the top

open again the covers on the steering column,something is out of place.

Posted on Nov 23, 2009

  • 66 Answers

SOURCE: turn signals were intermittent and now will not

It is absolutely possible, and recalls are free. Take the free recall and hope it solves your issue!

Posted on Dec 10, 2009

dturnlund
  • 45 Answers

SOURCE: my front turning signals will not flash,it is NOT

Look at you owner's manual, it should tell you where the fuse box is located.

Posted on Mar 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair turn signal lever


In order to repair the lever you must replace the turn signal switch, this requires the **** shell covers on the steering column to be removed, they are held on by 4 screws recessed in holes, then the switch is bolted to the steering column tube by two machine screws, do not break the wire connectors to the switch, remove them carefully. Always disconnect the battery negative cable before working on the steering column

Feb 10, 2012 | 1997 Nissan Pathfinder

1 Answer

Replace turn signal switch


Ensure lever is in center of off position.Disconnect negative battery cable. Disable airbag system. Remove steering wheel. Remove lower and upper column covers. Remove lock cylinder if necessary. Remove wiring harness strap. disconnect steering column electrical connectors. Disconnect turn-signal and multi-function switch Gray and Black connectors. Remove turn-signal and multi-function switch from vehicle.

Jun 05, 2011 | 1998 Chevrolet K1500

1 Answer

How do i install Switch Assembly turn signal Cruise control PART AUTO for a 2002 Impala.


Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

83422682


  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR system.
  4. Remove the steering wheel.
  5. Remove the steering column trim cover.
  6. Remove the steering column knee bolster.
  7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
  8. Remove the 2 wire harness straps from the steering column wire harness (1).
  9. Remove the steering column bulkhead connector from the vehicle wire harness.
  10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.
85097560




  1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
  2. Remove the multifunction turn signal lever (2) from the steering column.
Installation Procedure

85097560




  1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
  2. Verify that the electrical contact rests on the canceling cam.
Notice: Refer to Fastener Notice in Service Precaution.


  1. Install the retaining bolts to the multifunction turn signal lever.
    • Tighten the retaining bolts to 7 Nm (62 inch lbs.) .
92905224




  1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
  2. Connect the steering column bulkhead connector to the vehicle wire harness.
  3. Install the two wire harness straps to the steering column wire harness (1).
  4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
  5. Install the steering column knee bolster.
  6. Install the steering column trim cover.
  7. Verify that the lever is in the center or the OFF position.
  8. Install the steering wheel to the steering column.
  9. Enable the SIR system.
  10. Connect the negative battery cable.
I hope this helps you.

Thanks

Nov 28, 2010 | 2002 Chevrolet Impala

2 Answers

How to replace the turn signal switch in a 1992 Cadilac?


Turn Signal Switch REMOVAL & INSTALLATION CAUTION
Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column, and instrument panel disable the SRS. Deville, Eldorado, Seville, and Fleetwood - Early Models
  1. Disable the SIR system.
    1. On Deville and Fleetwood, remove the left lower sound insulator. On Eldorado and Seville, remove the left side sound insulator.
    2. Remove the Connector Position Assurance (CPA) and detach the yellow 2-way connector at the base of the steering column.
    3. Remove the steering wheel.
    4. Make sure the ignition switch is in the LOCK position to prevent the SIR coil assembly from going off-center.
  2. Remove the SIR coil assembly retaining ring and the coil assembly. Allow the coil to hang freely. WARNING
    The SIR coil assembly will become off-center if the steering column is separated from the steering gear and is allowed to rotate or if the centering spring is pushed down, letting the hub rotate while the coil is removed from the column.
  3. Remove the wave washer.
  4. Use tool J-23653-C or equivalents, to depress the shaft lock, then remove and discard the shaft lock retaining ring.
  5. Remove the shaft lock.
  6. Remove the turn signal canceling cam assembly.
  7. Remove the upper bearing spring, upper bearing inner race seat and inner race.
  8. Move the turn signal switch to the RIGHT TURN position.
  9. On Deville, Fleetwood, and 1990 Eldorado, and Seville, remove the multi-function turn signal lever as follows:
    1. Make sure the lever is in the OFF position.
    2. Remove the access cover from the steering column housing.
    3. Detach the cruise control wiring connector. Note the position of the connector when installed in the column.
    4. Pull the lever straight out of the turn signal switch.
  10. On Eldorado and Seville, remove the multi-function turn signal lever as follows:
    1. On 1992-93 vehicles, slide the connector cover toward the front of the vehicle.
    2. Unplug the electrical connector. On 1991 vehicles, note the position of the connector when installed in the column.
    3. Push the lever straight in, rotate clockwise 1?4 turn and pull the lever out of the switch.
  11. On Deville, Fleetwood, and Eldorado and Seville, remove the screw, button, spring, and hazard warning switch knob.
  12. On Deville and Fleetwood, remove the one signal switch arm retaining screw. On Eldorado and Seville, remove the 2 signal switch arm retaining screws. Remove the signal switch arm.
  13. Remove the turn signal switch retaining screws.
  14. Remove the wiring protector and detach the turn signal switch connector.
  15. Gently pull the wire harness through the column and remove the turn signal switch. prev.gif next.gif

Nov 12, 2010 | 1992 Cadillac DeVille

2 Answers

Whear is the safty neutral switch at for a 1991 chevy c1500


If it is an auto trans with column shift, that switch is on the steering column, above the brake pedal, close to the floorboard.
Might need to lower the upper end of the steering column where it bolts under the dash to get to it.

Jul 04, 2010 | 1991 Chevrolet C1500

2 Answers

Where are there free turn instructions available on how to replace a turn signal in a 1994 chevy silverado? I will pay $1 for this answer.


You posted in the fre section...no need for the dollar but I'll take a cold Corona and lime!


Here ya go....

Removal & Installataion

  1. Make sure the switch is in the OFF position.
  2. Remove the Steering Wheel as outlined in this section.
    1. Remove the instrument panel trim cover.
    2. Insert a screwdriver into the lockplate cover slot and pry out the cover. Remove the lockplate. A special tool is available to do this. The tool is an inverted U-shape, with a hole for the shaft. The shaft nut is used to force it down. Pry the wire snap ring out of the shaft groove. Discard the snap ring.
    3. Remove the tool and lift the lockplate off the shaft.
    4. Remove the turn signal lever screw and lever.
    5. Press the hazard button inward and unscrew it.
    6. Remove the switch retaining screws. Pull the switch connector out of the mast jacket and feed the switch connector through the column support bracket.
    7. Position the turn signal lever and shifter housing in the downward, or "low" position and pull downward on the lower end of the column using a pliers on the tab provided. Remove the wire protector.
    8. Remove the switch mounting screws. Remove the switch by pulling it straight up while guiding the wiring harness cover through the column.
  3. To install:
    1. Install the replacement switch by working the connector and cover down through the housing and under the bracket.
    2. Install the switch mounting screws and the connector on the mast jacket bracket. Install the column-to-dash trim plate.
    3. Install the flasher knob and the turn signal lever.
    4. With the turn signal lever in neutral and the flasher knob out, slide the thrust washer, upper bearing preload spring, and canceling cam into the shaft.
    5. Position the lockplate on the shaft and press it down until a new snap ring can be inserted in the shaft groove.
    6. Install the cover and the steering wheel.

59f71ca.gif
Retaining ring removal


1374c72.gif
Pliers may be used to remove the turn signal wire protector


7eb6477.gif
Removing the turn signal switch


1f13165.gif
Install the lockplate and the retaining ring using the tool illustrated (or its equivalent)

Jun 08, 2010 | Cars & Trucks

1 Answer

How to remove key unit from steering column 1986 F150 Ford


COUTESY OF EXPERT "C17HYDRO"
With Key
  1. Disconnect the battery ground.
  2. On tilt columns, remove the upper extension shroud by unsnapping the shroud from the retaining clip at the 9 o'clock position.
  3. Remove the trim shroud halves.
  4. Unplug the wire connector at the key warning switch.
  5. Place the shift lever in PARK and turn the key to ON.
  6. Place a 1/8 in. wire pin in the hole in the casting surrounding the lock cylinder and depress the retaining pin while pulling out on the cylinder.
  7. When installing the cylinder, turn the lock cylinder to the RUN position and depress the retaining pin, then insert the lock cylinder into its housing in the flange casting. Assure that the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will allow the cylinder retaining pin to extend into the cylinder cast housing hole.
  8. The remainder of installation is the reverse of removal.

This section is for a NON-TILT with no key or non-functioning cylinder:
Fixed Columns
  1. Disconnect the battery ground.
  2. Remove the steering wheel.
  3. Remove the turn signal lever.
  4. Remove the column trim shrouds.
  5. Unbolt the steering column and lower it carefully.
  6. Remove the ignition switch and warning buzzer and pin the switch in the LOCK position.
  7. Remove the turn signal switch.
  8. Remove the snapring and T-bolt nuts that retain the flange casting to the column outer tube.
  9. Remove the flange casting, upper shaft bearing, lock cylinder, ignition switch actuator and the actuator rod by pulling the entire assembly over the end of the steering column shaft.
  10. Remove the lock actuator insert, the T-bolts and the automatic transmission indicator insert, or, with manual transmissions, the key release lever.
  11. Upon reassembly, the following parts must be replaced with new parts:
    • Flange
    • Lock cylinder assembly
    • Steering column lock gear
    • Steering column lock bearing
    • Steering column upper bearing retainer
    • Lock actuator assembly
  1. Assembly is a reversal of the disassembly procedure. It is best to install a new upper bearing. Check that the vehicle starts only in PARK and NEUTRAL.

This section is for TILT and no key or non-functioning cylinder:

Tilt Columns
  1. Disconnect the battery ground.
  2. Remove the steering column shrouds.
  3. Using masking tape, tape the gap between the steering wheel hub and the cover casting. Cover the entire circumference of the casting. Cover the seat and floor area with a drop-cloth.
  4. Pull out the hazard switch and tape it in a downward position.
  5. The lock cylinder retaining pin is located on the outside of the steering column cover casting adjacent to the hazard flasher button.
  6. Tilt the steering column to the full up position and prepunch the lock cylinder retaining pin with a sharp punch.
  7. Using a 1/8 in. drill bit, mounted in a right angle drive drill adapter, drill out the retaining pin, going no deeper than 1/2 in. (12.7mm).
  8. Tilt the column to the full down position. Place a chisel at the base of the ignition lock cylinder cap and using a hammer break away the cap from the lock cylinder.
  9. Using a 3/8 in. drill bit, drill down the center of the ignition lock cylinder key slot about 13/4 in. (44mm), until the lock cylinder breaks loose from the steering column cover casting.
  10. Remove the lock cylinder and the drill shavings.
  11. Remove the steering wheel.
  12. Remove the turn signal lever.
  13. Remove the turn signal switch attaching screws.
  14. Remove the key buzzer attaching screw.
  15. Remove the turn signal switch up and over the end of the column, but don't disconnect the wiring.
  16. Remove the 4 attaching screws from the cover casting and lift the casting over the end of the steering shaft, allowing the turn signal switch to pass through the casting. The removal of the casting cover will expose the upper actuator. Remove the upper actuator.
  17. Remove the drive gear, snapring and washer from the cover casting along with the upper actuator.
  18. Clean all components and replace any that appear damaged or worn.
  19. Installation is the reverse of removal. Check for proper operation.

Nov 23, 2009 | 1986 Ford F150 SuperCab

2 Answers

Diagram on to change turn signal arm on 1994 chevy cavalier , do u have to pull the sterring wheel


1991-94 Cavalier
See Figure 5
This procedure covers removal and installation of the headlamp, headlamp dimmer switch, turn signal and hazard switches, as well as the cruise control switch.
  1. If equipped, disable the SIR system. For details, please refer to the procedure located in of this repair guide.



0900c1528003bf08.jpg enlarge_icon.gif enlarge_tooltip.gif Fig. Fig. 5: View of the steering column showing the turn signal switch location
  1. If not already done, disconnect the negative battery cable.
  2. Unfasten the horn pad, then remove the steering wheel. For details, please refer to the procedure earlier in this section.

If necessary, using locking pliers with a piece of rubber (such as a spark plug boot) between the jaws to help prevent damage to the tilt lever during removal.
  1. If equipped, remove the tilt lever from the steering column by grasping the lever firmly and twisting counterclockwise, while pulling it from the column.
  2. Remove the upper and lower steering column covers.
  3. Remove the dampener assembly, then unfasten and remove the switch assembly from the vehicle.

To install:
  1. Position and secure the switch assembly.
  2. Install the dampener and the upper and lower steering column covers.
  3. If equipped, attach the tilt lever to the column.
  4. Install the steering wheel, then fasten the horn pad.
  5. If equipped, enable the SIR system, as outlined in of this repair guide.
  6. Connect the negative battery cable.

Nov 15, 2009 | 1994 Chevrolet Cavalier

1 Answer

How to replace ignition lock cylinder on 1984 Ford F-150 pickup?


With Key
  1. Disconnect the battery ground.
  2. On tilt columns, remove the upper extension shroud by unsnapping the shroud from the retaining clip at the 9 o'clock position.
  3. Remove the trim shroud halves.
  4. Unplug the wire connector at the key warning switch.
  5. Place the shift lever in PARK and turn the key to ON.
  6. Place a 1/8 in. wire pin in the hole in the casting surrounding the lock cylinder and depress the retaining pin while pulling out on the cylinder.
  7. When installing the cylinder, turn the lock cylinder to the RUN position and depress the retaining pin, then insert the lock cylinder into its housing in the flange casting. Assure that the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will allow the cylinder retaining pin to extend into the cylinder cast housing hole.
  8. The remainder of installation is the reverse of removal.

This section is for a NON-TILT with no key or non-functioning cylinder:
Fixed Columns
  1. Disconnect the battery ground.
  2. Remove the steering wheel.
  3. Remove the turn signal lever.
  4. Remove the column trim shrouds.
  5. Unbolt the steering column and lower it carefully.
  6. Remove the ignition switch and warning buzzer and pin the switch in the LOCK position.
  7. Remove the turn signal switch.
  8. Remove the snapring and T-bolt nuts that retain the flange casting to the column outer tube.
  9. Remove the flange casting, upper shaft bearing, lock cylinder, ignition switch actuator and the actuator rod by pulling the entire assembly over the end of the steering column shaft.
  10. Remove the lock actuator insert, the T-bolts and the automatic transmission indicator insert, or, with manual transmissions, the key release lever.
  11. Upon reassembly, the following parts must be replaced with new parts:
    • Flange
    • Lock cylinder assembly
    • Steering column lock gear
    • Steering column lock bearing
    • Steering column upper bearing retainer
    • Lock actuator assembly
  1. Assembly is a reversal of the disassembly procedure. It is best to install a new upper bearing. Check that the vehicle starts only in PARK and NEUTRAL.

This section is for TILT and no key or non-functioning cylinder:

Tilt Columns
  1. Disconnect the battery ground.
  2. Remove the steering column shrouds.
  3. Using masking tape, tape the gap between the steering wheel hub and the cover casting. Cover the entire circumference of the casting. Cover the seat and floor area with a drop-cloth.
  4. Pull out the hazard switch and tape it in a downward position.
  5. The lock cylinder retaining pin is located on the outside of the steering column cover casting adjacent to the hazard flasher button.
  6. Tilt the steering column to the full up position and prepunch the lock cylinder retaining pin with a sharp punch.
  7. Using a 1/8 in. drill bit, mounted in a right angle drive drill adapter, drill out the retaining pin, going no deeper than 1/2 in. (12.7mm).
  8. Tilt the column to the full down position. Place a chisel at the base of the ignition lock cylinder cap and using a hammer break away the cap from the lock cylinder.
  9. Using a 3/8 in. drill bit, drill down the center of the ignition lock cylinder key slot about 13/4 in. (44mm), until the lock cylinder breaks loose from the steering column cover casting.
  10. Remove the lock cylinder and the drill shavings.
  11. Remove the steering wheel.
  12. Remove the turn signal lever.
  13. Remove the turn signal switch attaching screws.
  14. Remove the key buzzer attaching screw.
  15. Remove the turn signal switch up and over the end of the column, but don't disconnect the wiring.
  16. Remove the 4 attaching screws from the cover casting and lift the casting over the end of the steering shaft, allowing the turn signal switch to pass through the casting. The removal of the casting cover will expose the upper actuator. Remove the upper actuator.
  17. Remove the drive gear, snapring and washer from the cover casting along with the upper actuator.
  18. Clean all components and replace any that appear damaged or worn.
  19. Installation is the reverse of removal. Check for proper operation.

Oct 13, 2009 | 1984 Ford F 150

3 Answers

How to replace my turn signal switch


Multi-function Switch Removal & Installation To Remove:
To Remove:
  1. Remove the steering column trim covers.
  2. Remove the wire harness from the retainers as needed.
  3. Slide the turn signal and multifunction switch connectors out from the bulk head connector.
  4. Remove the two mounting screws and remove the multi-function switch from the steering column.

To Install:
  1. Install the multi-function switch on the steering column.
    • Tighten the screws to 42 lb in (4.7 Nm).
  2. Slide the turn signal and multifunction switch connectors into the bulkhead connector.
  3. Install the harness in the original retainers.
  4. Install the steering column trim covers.
7f81df3.gif

Jun 25, 2009 | 1996 GMC Sierra

Not finding what you are looking for?
1990 Oldsmobile Ninety Eight Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...