Question about Cars & Trucks

1 Answer

How to ajust if any, the clutch on toyota townace 2c.

Clutch just about engages at end of travel

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 645 Answers

More information?----------------------------------------
Car Key Programmer

Posted on Dec 01, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 1979 ford f350 clutch pedal travel 1/2 inch

sounds like the clutch armerature may be hanging or broke. it's the rod that ingages the clutch.

Posted on Apr 17, 2009

  • 156 Answers

SOURCE: Where do you refill the oil in a Toyota Townace

Dipstick, oil filler , filter etc are under the passengers front seat.
If you lift the carpet immediately in front of the seat, you will see a pair of clips holding down the seat, unlatch them and lift the seat ( in some models they hide a clip in the centre console).
The brake fluid is under a cover in the dash.

Posted on Mar 27, 2010

ftw1952
  • 10319 Answers

SOURCE: have flashing light on toyota townace not sure why

Try this website for resolving car problems by downloading a FREE service manual for your vehicle. This is not an owners manual but a factory mechcanic's manual.

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 01, 2010

SOURCE: 2007 toyota tundra a/c clutch won't engage. Is there a fuse or relay?

Hi Jim, When that happens it usually means that the gas has leaked out and the pressure in the system is too low to operate. There are pressure sensors in the system for just that reason. Have the pressure checked, or if you live somewhere where you can buy the do it yourself kits, purchase one and check the pressure. If not you would do well to go see a refrigeration technician. There are relays and fuses but the most likely cause is the one I've mentioned. Regards John

Posted on Nov 11, 2011

emissionwiz
  • 75235 Answers

SOURCE: Freelander td4 2004, clutch pedal at rest position is too low, when you press the clutch in you don't get full travel and gears are stiff to engage.

You have a leaking master or slave hydraulic clutch cylinder. I recommend you replace both

Posted on Jul 20, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many km can a clutch disc last on a new toyota quantum? Thrre is a quantum that travels 120km par day in a congetion trafic and now it on 30000km the presure is week


the life of the clutch depends on the driver action
riding the clutch , using 2nd gear instead of 1st gear, driving conditions all are responsible for shortened clutch life. average clutch plate life is around 100,000miles in good conditions with good driving habits
however if the vehicle is over 3 years old , it could be a problem in the clutch master cylinder or clutch cable that is not allowing full clutch engagement and that will give indications of clutch failure

May 09, 2017 | Toyota Cars & Trucks

1 Answer

1994 toyota pickup


No, this is a hydraulic clutch and the only adjustment may b on the pedal linkage for free travel to the master cylinder. It sounds as though you may have a bad clutch master cylinder or defective slave cylinder.

Apr 26, 2014 | 1994 Toyota Pickup

1 Answer

Slipping Clutch on Toyota Townace 1988 Van.


Check that the slave cylinder is fully releasing the clutch (push the clutch fork and shaft all the away back into slave cyl.. If ok replace the clutch assy.

Mar 29, 2013 | Toyota Cars & Trucks

1 Answer

The Clutch Engages at the end of pedal travel


Adjust your clutch pedal free play (clearance). It should be around 12mm only.

Oct 29, 2012 | Cars & Trucks

1 Answer

Toyota townace service manual


How many litters of Ingine oil of Toyota townace

Mar 15, 2012 | Toyota Cars & Trucks

2 Answers

I dont know were the clutch cable ajustment is.


There is no clutch cable. The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on the clutch housing. The clutch release cylinder is not adjustable. Clearance is automatically compensated for by internal design of the cylinder.

If your clutch is not releasing properly, the most likely cause is a worn out clutch disc, which will require more travel to disengage than the hydraulic system is designed to provide. It is either this, or your master and/or slave cylinders need replacement.

May 24, 2011 | 1992 Toyota Corolla

1 Answer

1990surf clutch wont return from floor all the time wont disingage?? what the pedal ajustment free play??Ralphy


the pedal freeplay should be about a quarter of an inch. This is the area the pedal travels before the first amount of pressure is applied. have you checked your clutch fluid? if its low you should scope for leaks, check the master cylinder and slave cylinder, pull back the rubber boot and check for any fluids. i would do this only if the fluid is low. have you had any clutch work done recently?

Jan 22, 2011 | 1992 Toyota 4Runner

1 Answer

After traveling about 8km my car wont go into 1st or reverse gear. when it is cold it goes into all the gears fine. when i switch the car off it will go into gear. we did put a new(aftermarket clutch) in a...


Cluth cable ajustment if equiped.Some cars have a cluth cylender if your model has the cylender no ajustment is available.If you had your cluth changed at a garage you might consider takeing it back in for ajustments.If you changed the clutch check cluth cable for ajustment if your car is equiped with cable if not i would perhaps remove the transmission and inspect clutch for loose clutch plate or release bearing might not be seated properly hope this helped you.

Dec 24, 2009 | Mazda 323 Cars & Trucks

2 Answers

Toyota 2ct diesel turbo in 4x4 Townace van 1991 model Pumping water out of overflow hose, no sine of oil in radiator, no sine of water or stem in tail pipe, motor idle ok, starts fine, thermostat test ok,...


it is the head gasket blown from the cyl to the water jacket ,a radiator specialist can test for combustion gases in the water to confirm this ,but that is what it is . "youdoit"

Oct 25, 2009 | Toyota Passenger Cars & Trucks

1 Answer

Clutch adjustment for toyota corolla 1984


the clutch is hydraulic and self adjusting, if it is slipping then it is time for a clutch, the sign of a worn clutch is the clutch engages when the pedal is near the top of its travel when u let it out

Apr 12, 2009 | 1984 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...