Question about 1996 Pontiac Grand Am

1 Answer

Thermostat needs replaced

Do I have to remove the manifold to replace thermostat

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 645 Answers

To replace a thermostat, you will need at least: 1. A new thermostat 2. Screwdriver 2. Needle-nosed pliers. Depending on the thermostat and location in your home, you may need more. Make sure the new thermostat you are using to replace the old one with is compatible to your 110-volt housing circuitry. Always turn off the electrical power to the home thermostat at the power panel or circuit breaker box.--------------------------------------------------------------------------
carbrain c168 scanner

Posted on Dec 01, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thermostat housing is leaking i need remove throttle body upper intake manifold for ford explorer Eddie Bauer


If it is a single overhead can 4.6 liter v8 the intake manifold is notorious for leaking on that model of ford engine I just replaced one on a friends explorer the seal on the intake manifold deteriorates causing the leak and replacement of the manifold is the only solution! Good luck!

Jan 04, 2015 | Ford Cars & Trucks

1 Answer

Bad theromostat 3.2 isuzu how to


The thermostat on the 2001 Isuzu Rodeo 3.2L v6 is located on the top of the engine under the upper intake manifold. In order to replace it you will have to depressurize the fuel system by running the engine with the fuel pump fuze removed until the engine dies and then carefully remove the fuel rail and injectors. Then remove the intake manifold which will give you access to the coolant nozzle fixture attached to the top of the engine. The thermostat is in the top of the engine block under the nozzle fixture. Be sure to replace the thermostat with the proper replacement part (may be difficult to find) and put on new gaskets for the intake manifold before replacing it.

Apr 11, 2013 | 2001 Isuzu Rodeo

1 Answer

Need to know how to replace the thermostat on a 1996 buick century wagon 3.1 6 cylinder engine



Trace the upper radiator hose to the mounting area on the intake manifold. Loosen the hose clamp on the manifold end of the hose and remove the hose. Pull the thermostat out of the intake manifold.

For more help and troubleshooting go through the help links below:---

Click the link below:-----





THERMOSTAT REMOVAL PROCEDURE/LOCATION DETAILS

------------

Where is Thermostat Located on Saturn

http://technoanswers.blogspot.com/2012/11/where-is-thermostat-located-on-saturn.html

----------

2004 Dodge Intrepid: How to replace Thermostat?

http://schematicsdiagram.blogspot.in/2012/06/2004-dodge-intrepid-how-to-replace.html

---------

How to Replace Thermostat on Audi A4?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-thermostat-on-audi-a4.html

---------

How to replace Thermostat on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-thermostat-on-acura-car.html

-------------

Where is thermostat located on 2006 dodge magnum 3.5L?//

http://repairhelpcenter.blogspot.com/2011/10/where-is-thermostat-located-on-2006.html


----------

Thermostat on AUDI 1.9 TDI?

http://repairhelpcenter.blogspot.com/2011/10/thermostat-on-audi-19-tdi.html

-----------

How to replace Radiator on Audi and VW car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-radiator-on-audi-and-vw.html


--------------

How to Replace a Thermostat.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-thermostat.html


-------------

How to locate Thermostat on Any car model?

http://schematicsdiagram.blogspot.com/2011/12/how-to-locate-thermostat-on-any-car.html

--------

Where is thermostat on Audi A6?

http://technoanswers.blogspot.com/2011/12/where-is-thermostat-on-audi-a6.html

-------

How to replace thermostat on 1992 Buick century?

http://technoanswers.blogspot.com/2011/12/how-to-replace-thermostat-on-1992-buick.html

------

Replacing thermostat on 1999 Mercury Cougar?

http://technoanswers.blogspot.com/2011/12/replacing-thermostat-on-1999-mercury.html

------

Thermostat Replacement on Toyota Corolla?

http://technoanswers.blogspot.com/2011/12/thermostat-replacement-on-toyota.html

--------

Where is thermostat located on 2005 Dodge neon?

http://schematicsdiagram.blogspot.in/2012/02/where-is-thermostat-located-on-2005.html
--------
These will help.
Thanks.

Nov 28, 2012 | Buick Century Cars & Trucks

1 Answer

Replace themostst


Hello ,

The thermostat is located on the right side of the engine looking in,between the intake manifold and the air filter box, underneath the wiring. This is in a 1994 Ford Probe GT 6 cylinder.

To replace the thermostat, you really need to remove the intake manifold and this can be up to two or three hours work alone, even for a qualified mechanic.

It is in the housing at the engine end of the upper rad hose. When replacing it make sure the spring on the thermostat is toward the engine.

NOTE: Remove the air intake box so you can see below. There is a pipe running right into the bell housing where the thermostat is housed. There is one bolt that you need to remove (it is to the right,below the distributor) Then there are the other 12 mm bolts on the bell of the thermostat housing to remove. After removing those the thermostat should be able to come right out.

Thank you, hope this helps you out.
Bill
mr1bill_1.jpeg.

Aug 07, 2011 | 1994 Ford Probe

1 Answer

Need to replace the themostat


  • Remove the bolts that hold the thermostat housing onto the intake manifold of the MR2 with an adjustable wrench and pull up on the thermostat housing to remove it from the intake. The housing is still connected to the hose. Lift the thermostat housing and the hose up to drain the antifreeze back into the radiator.
  • 2 Remove the old thermostat from the hole inside of the intake manifold and replace it with a new one. Pull the thermostat gasket off of the top of the intake manifold and wipe the manifold clean with a towel.
  • 3 Place a bead of RTV gasket maker around the bottom edge of the thermostat housing and allow it to dry for 15 minutes. Place the thermostat housing back onto the intake manifold and bolt the housing back into place. Allow 15 more minutes of drying time and slightly tighten the bolts again. This will form a solid seal between the intake manifold and the thermostat housing.



  • Dec 23, 2010 | 1991 Toyota MR2

    1 Answer

    Thermostat replacement diagram


    Please see my tip at http://www.fixya.com/cars/r5929960-s_thermostat . These are generic instructions. specific instructions for your car are provided below. please get back to me with any questions.

    Colt and 1990-91 Vista

    1. Disconnect the negative battery cable.
    2. Drain the cooling system to a point below the thermostat level.
    3. Remove the air cleaner.
    4. Disconnect the hose at the thermostat water pipe.
    5. Remove the water pipe support bracket nut.

    This nut is also an intake manifold nut. It is very difficult to get to. A deep offset 12mm box wrench is used to remove or replace it.
    1. Unbolt and remove the thermostat housing and pipe.
    2. Lift out the thermostat. Discard the gasket.

    To install:


    jturcotte_341.gif

    Fig. Fig. 1: Thermostat - 1990-92 Colt Hatchback. The 1.6L is 1990 only

    1. Clean the mating surfaces of the housing and manifold thoroughly.
    2. Install the thermostat with the spring facing downward and position a new gasket. The jiggle valve in the thermostat should be on the manifold side.
    3. Install the housing and pipe assembly. Torque the housing bolts to 11 ft. lbs. (14 Nm); the intake manifold nut to 14 ft. lbs. (19 Nm).
    4. Refill the system with coolant. Connect the negative battery cable.
    5. Start the engine and check for leaks.

    Nov 28, 2010 | 1991 Dodge Colt

    1 Answer

    Thermostat replacement


    HI there,

    Well first of all you may please follow the steps below -

    1. Remove the upper radiator hose from the thermostat intake tube by loosening the retaining clip with a screwdriver. Slide the clip toward the radiator and pull the hose off the thermostat intake tube. 2. Remove the two 10-mm bolts that hold the thermostat intake tube onto the intake manifold of the Hyundai Accent. Pull the intake tube off the intake manifold and inspect it for cracks. If any cracks are present, then you need a new thermostat intake tube.
    3. Pull the old thermostat and thermostat gasket off the engine with your hands and replace them both with new ones. The thermostat will be marked with "top." This end should stick out of the engine. 4. Place the thermostat intake tube back onto the intake manifold of the Hyundai Accent and bolt it back into place. 5. Slide the radiator hose back on to the thermostat intake tube and secure it in place with the retaining clip. A band clamp can be used in place of the retaining clip for extra clamping pressure. Post comments for further help or information............

    Good Luck!!

    Thanks for suing FixYa!!

    Oct 13, 2010 | 2003 Hyundai Accent

    3 Answers

    I need to find the truck termostat, where is it?


    The thermostat is located in the front of the intake manifold under the thermostat housing, and follow the upper radiator hose over to where it connects to the engine on the intake manifold and that will be the thermostsat housing. remove the upper radiator hose from the thermostsat housing and remove the ground wire if there is one attaced to one of the two thermostat housing studs, and then remove the two studs/bolts from the thermostat housing and then remove the thermostat from the intake manifold. Be sure to replace the thermostat correctly and here is an image to help assist you.


    b932050.jpg

    Sep 10, 2010 | 1997 Chevrolet C1500

    1 Answer

    Where is the thermostat


    THE 2.4 ENGINE THERMOSTAT LOCATED NEAR THE EXHAUST MANIFOLD YOU HAVE TO REMOVE MANIFOLD HEAT SHIELD TO GET TO IT. THE 3.4 AND 3.1 THERMOSTAT UNDER LOWER INTAKE MANIFOLD ON DRIVER SIDE.YOU HAVE TO REMOVE THROTTLE BODY UNIT AND COOLANT LINES HOOK TO IT TO MAKE EASIER TO REMOVE THERMOSTAT HOUSING TO REPLACE THERMOSTAT.

    May 15, 2010 | 1999 Oldsmobile Alero

    1 Answer

    Intake manifold sealant repair now leaking maybe oil? coolant b4


    You need to remove the thermostat housing again. Then you will have to extract the bolts you broke off. You will need to drill and tap them so you can use an easy out to remove the broken bolts from the threads. Then you can clean up both mating surfaces and replace the gasket and the thermostat. Check to make sure you did not crack the thermostat housing or you may have another leak when finished. They are usually aluminum and break easily if too much pressure is applied or they are corroded and weak.

    Feb 25, 2009 | 1999 Ford Taurus

    Not finding what you are looking for?
    1996 Pontiac Grand Am Logo

    416 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...