Question about Cars & Trucks

Open Question

I am fitting a oil pressure guage to my mazda bravo b2500 2005,and was wondering where the oil pressure switch is located??

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 75 Answers

SOURCE: location of the fuel pump relay or fuse

fuel pump in the fuel tank note that all ford are equipt with cut of suitch (interuptor) located under dach board in case of colision ,towing, ect.....this electrical devise wil stop the flow of the fuel to prevent car fire

Posted on Dec 21, 2008

Ad
  • 6982 Answers

SOURCE: difference between oil sending unit and the oil pressure switch

Same part...make sure you get one for gauge, not idiot light though. If the engine has any knocking or ticking when pressure drops do not drive it and have a mechanical gauge installed to check actual pressure. Parts often have different names for same item...your driveshaft is actually called a propeller shaft!!!

Posted on Sep 18, 2009

honeymokey
  • 3113 Answers

SOURCE: oil pressure guage occassionly drops to 0 psi and warning light g

Get it checked with a mechanical gauge. Replace sensor.

Posted on Sep 28, 2009

240SXer
  • 100 Answers

SOURCE: location of oil pressure switch on a 1997 cadillac deville

Oil pressure switches a normally located by or near the oil filter on all cars. :-)

Posted on Dec 25, 2009

BCAS1298
  • 3092 Answers

SOURCE: where is oil pressure guage sending unit located

On top of the engine, to the back, below the distributor.

Posted on Sep 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have a mazda bounty/bravo 2005 2.5 td wl engine. The engine has a a slight tapping noise once it reaches operating temp.it is more noticeable at idle. I have done the tappets to spec but that didn't...


First I'd put a manual oil pressure gauge on it to verify it's holding proper pressure. If it passes the test it could be as simple as a collapsed oil filter or possibly a bad lifter.

Feb 18, 2015 | Mazda Cars & Trucks

2 Answers

How do I check oil pressure with a guage


Remove the oil pressure switch. It is typically located near the oil filter. Install the appropriate fitting from the oil pressure gauge kit. Install the gauge. Start the vehicle.

Jul 08, 2014 | 2000 Jeep Grand Cherokee

1 Answer

1998 mazda bravo ute b2600 petrol- Cannot locate the oil filter to change. Can find the sump and bung. Is it possible this model has no oil filter?


No!!!! The motor has oil filter.Look from the top of the motor.It is right there.Under the manifold.Hope this helps

May 25, 2011 | 1998 Mazda B-Series

3 Answers

How to you check to see if the oil pressure guage is bad or if there's a pressure problem itself?


Connect test leads to the guage and apply 12 volts, if the guage activates upward this works, if it's the oil preaaure in regards to the oil pump, you need to hook up a oil pressure guage.

Mar 31, 2011 | 1991 Ford F150

1 Answer

What is the safest and easy way to install amp meter and oil pressure meter?


The amp meter can be installed in the section of the voltage rectifier/regulator. This is not needed in the present models as they were used when a DC Dynamo was used.
The Oil pressure guage can be used along with the oil pressure switch, use a T-connector of the same thread and connect both the oil switch and pressure guage to it.
If this is not available then you can get this fabricated with the same thread size for all the fittings

Sep 13, 2010 | Kia Sportage Cars & Trucks

1 Answer

1992 mazda navajo oil gauge bounces


Could be a faulty oil pressure sender switch ( quite a common fault ) . Remove it and fit a mechanical gauge to test.
Much less likely ( if the test shows fluctuating pressure) the oil pressure bypass valve may be sticking. Make sure your oil is nice and clean, contaminants can sludge up the oilways. The bypass valve is usually in or near the oil pump on most cars.
My pick would be the switch.
Happy hunting!!

Apr 17, 2010 | 1992 Mazda Navajo

1 Answer

Oil light keeps flashing on and off when stationary oil ok new oil pressure switch fitted


what is the oil pressure when measured with a mechanical test guage?

Jul 08, 2009 | Kia Sephia Cars & Trucks

1 Answer

I have a 2006 Mazda 6 here in Australia and wont to fit a electric oil pressure guage. Wear do i put the sender


I believe you have to put in place of the oil pressure swtich that is already on the block of the engine to determine low oil pressure.

Apr 24, 2009 | 2006 Mazda 6

1 Answer

Location of oil pressure switch.


how change oil pressure sensor in 2001 mazda mpv dx

Apr 10, 2009 | 2001 Mazda MPV

1 Answer

No oil pressure


Sounds like sending unit, should be located by where the oil filter is.

Feb 26, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...