Question about 2001 Pontiac Aztek

Open Question

How to replace thermostat in Pontiac aztek - 2001 Pontiac Aztek

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
airjer995
  • 5332 Answers

SOURCE: 2004 pontiac aztek thermostat replacement?

The thermostat is located behind the metal housing that is bolted to the intake manifold on the drivers side of the engine below the throttle body.

There are 2 bolts holding the hosing on. A 13mm swivel socket and a 13mm wrench will be needed to remove the bolts.

Sometimes it is easier to remove the throttle body if it is your first time. It will let you see what you are doing a little better.

1. remove the air cleaner cover and hose attached to the throttle body.
2. remove the throttle body (optional)
3. Using a swivel socket and wrench remove the 2 bolts holding the thermostat housing from the intake manifold.

airjer995_36.jpg

Posted on Jan 30, 2011

Ad
  • 74 Answers

SOURCE: 2004 pontiac aztek cooling fans not working

relays control fans high and low. does fan come on with a/c on?hot wiring only will create more expensive problems in future!!!!! 2004 not 84

Posted on Aug 26, 2008

  • 1 Answer

SOURCE: Rear Wheel Bearing Repair; 2005 pontiac aztek

Remove the brake caliper
Remove the disc, (rotor)
Remove the 34mm nut on the axel shaft
Remove the three (3) bolts from the back side
You will need a wheel puller (three jaw will work well)
Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

Posted on May 03, 2009

  • 299 Answers

SOURCE: Pontiac Aztek Pressuer Control Solenoid

They will have to remove trans end cover to perform this,will take several hours to perform.

Posted on Jun 21, 2009

  • 54 Answers

SOURCE: I need help to replace the thermostat in a 2002

go to www.autozone.com and become a memmber add the aztek to the list (free service)

Posted on Jun 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need know how get shift out streeling knuckle on 2004 Pontiac Aztek front wheel drive what all tools i need


2004 Aztek: replace the right front steering knuckle - JustAnswer

www.justanswer.com > Car Questions > Pontiac Problems
2004 Aztek: replace the right front steering knuckle - Answered by a verified Pontiac Mechanic.

How do i change a CV Joint on a pontiac aztek - JustAnswer

www.justanswer.com > Car Questions Disconnect the outer tie rod end from the steering knuckle; do NOT loosen the tie rod end jam nut. Refer to Rack and Pinion Outer Tie Rod End Replacement in ...

steering knuckle video for 2004 Pontiac Aztek Google Search

Jun 25, 2017 | Pontiac Cars & Trucks

1 Answer

My 04 aztek is overheating it had a small leak in the metal hose for the radiator we replaced that it was ok for about 10 miles heat and all then it over heated again so we replaced the thermostat and...


check see if your engine is getting wet near the cylinder if so u got the intake gasket leaking coolant with majority of it going in the oil, also u should replace thermostat

Feb 23, 2015 | 2004 Pontiac Aztek

1 Answer

Were is the theromstat on 2003 ponatic aztek


follow the top hose from your radiator to where it attaches to the motor should hook to a flange mounted by two bolts normally thermostat housing its called thermostst inside

Dec 12, 2012 | 2003 Pontiac Aztek

2 Answers

Leaking antifreeze on radiator, now overheating, does that mean thermostat needs replacing


Hello, iconway3 and thank you for asking your question on Fixya!

Here is a simple process that will walk you through a few steps that will pinpoint the overheating problem on your
2001 Pontiac Aztek, without even using any tools. It has helped millions of people, and I am certain that it will help you, because I wrote it for people in your exact situation.
How to diagnose your overheating
2001 Pontiac Aztek

Get more great money saving tips and tricks about your vehicle from: twitter.com/acoates23234

Thanks for the vote, and good luck!

Nov 22, 2010 | 2001 Pontiac Aztek

1 Answer

Have an intermittent overheating problem with my 2003 Pontiac Aztek. I have replaced the intake manifold gasket three months ago. Along with that I changed the thermostat. I notice no leaking. I have also...


I had a similar problem with an Olds Intrigue. It turned out to be the aftermarket ( NAPA ) thermostat. I bought a thermostat from GM the problem went away. I typed my problem into google and found where GM had sent out a service bulletin on the problem and had come up with an "enhanced designed thermostat". I hope this helps, good luck.

Mar 27, 2010 | 2003 Pontiac Aztek

1 Answer

How do i change my thermostat on my 2001 pontiac aztek. also how do i remove the crossover exhaust pipe to get to the @#$%^ing thing?


Exhaust Crossover Pipe Replacement
Removal Procedure
  1. Disconnect the battery ground (negative) cable.
  2. Remove the throttle body air inlet duct.
  3. Drain the coolant from the cooling system.
  4. Remove the inlet radiator hose from the engine.
  5. Remove the thermostat bypass pipe.
  6. Remove the exhaust crossover heat shield bolts.
  7. Remove the exhaust crossover heat shield.
89160026

  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.
  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
  6. Remove the thermostat housing and gasket.
Removal Procedure

89153578

Dec 11, 2009 | 2003 Pontiac Aztek

1 Answer

Overheating 2001 pontiac aztek


remove coolant.remove thermostat remove bottom radiator hose to water pump.put a empty container under the radiator.take a water hose put it where thermostat goes flush out the rust in block.watch the water as it come out the water pump .if stream water is small keep flushing until you get a study sream of clear water. also flush out radiator. lower water pressure dont flush radiator it with high water pressure you could burst it. make clean the over flow jug .make sure it not stopped up.put in a new thermostat and radiator pressure cap. fill radiator with half antifreeze and half water.bleed the coolant system.

Apr 05, 2009 | 2001 Pontiac Aztek

1 Answer

2004 pontiac aztek cooling fans not working


relays control fans high and low. does fan come on with a/c on?hot wiring only will create more expensive problems in future!!!!! 2004 not 84

Aug 26, 2008 | 2005 Pontiac Aztek

Not finding what you are looking for?
2001 Pontiac Aztek Logo

Related Topics:

1,696 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...