Question about 1998 Ford Explorer

2 Answers

I installed new roters and calipers on the front of my 1998 explorer and new brakes on the rear.now the brake pedal goes all the way to the floor even after we bled the brakes

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

Dealership has to use scanner and pressure bleeder to bleed brake system.

Posted on Dec 01, 2012

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,630 Answers

You need a special tool to bleed the brakes on this truck, you need to have the dealer bleed the brakes using that tool.

Posted on Nov 30, 2012

Testimonial: "not what i really wanted to hear lol but thanks alot"

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: 2001 Mustang GT rear brake job

yep this is a two man job, onece you get air in the lines is better to do all four, my has abs and i was able to do it, but next time don't take anylines lose just turn the piston clockwise and you should be able to push it in.

Posted on Oct 12, 2008

  • 23 Answers

SOURCE: stuck calipers

Brake lines are not releasing fluid back to master cylinder. Open bleeder and see if wheel will turn. If it does replace brake line to caliper

Posted on May 08, 2010

  • 17 Answers

SOURCE: 1998 Ford Explorer brake problem

these rotors are known for rusting onto the vehicle. when you removed them you probably had to beat them off with a hammer. if this is the case then you may have a small amount of surface corrosion on the hub. this could cause your rotor to not sit evenly and cause a wobble. recommend removing the new rotor and cleaning the surface of the hub

Posted on Dec 01, 2008

  • 65 Answers

SOURCE: 2005 f150 spongy brakes

it sounds like your still not getting all the air out of your lines. it helps to have a brake bleeder but they are expensive, it also could be that the gasket inside the master cylinder is inverted even if it is a new master cylinder this could be the case, ive had four bad remanned ones in a row, before i got a good one... hope i could help

Posted on Mar 24, 2009

jaysonemanme
  • 500 Answers

SOURCE: Brakes

check to see you haven't mounted the calipers on the wrong sides. bleeders should be on top not the bottom. RABS block is on the framerail near the drivers door

Posted on May 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998 Ford Explorer Sport. I have


my friend , it is the problem of the brake boosters, it is between the brake pedal and cylinder , try to change a new one. check here for information: http://www.fiverhope.com , and you have to check your booster type, single vacuum booster or dual vacuum booster

Sep 16, 2013 | Cars & Trucks

1 Answer

Brake pedal goes to floor


for the pedal to go to the floor there is still air in the brake system. Start again starting from the longest line bleeding each in turn to the shortest line . make sure you have adjusted up the rear brakes before bleeding as every time you press on the pedal the shoes expand right out and when you take your foot off the pedal the shoes go all the way back in. adjust them manually and do not rely on the self adjuster as it only adjusts on wheel movement

Jul 15, 2013 | 2002 Ford Explorer Sport Trac

1 Answer

2001 Silverado 2500 HD Why Rear brakes don't work after I installed new hydro-boost power booster, master cylinder, calipers, and pads. I bled master cylinder before installing, and brakes beginn


Hello Patricia,

Have you checked the master brake cylinder reservoir for brake fluid loss?

I don't suspect the master cylinder as you have replaced it... but am more suspect of a leaking brake line or fitting which should have
been discovered when you had the system bled.

The only time I ever had a rear brake problem with a 2500 series Chevrolet was due to seized rear brake caliper guide pins...as your calipers are also new that is not your problem.

If your brake pedal feels spongy and travels to the floor board you have air in the system, a brake fluid leak or a failure in the power steering system, such as a broken hose, broken power steering pump drive belt, or failed pump, would result in a loss of pressure to both the hydro-boost and steering.

Find more information here:

. Hydro Boost Power Assist Systems Operation Diagnosis and Repair

Jul 23, 2017 | 2001 Chevrolet Silverado 2500HD

2 Answers

I have replaced front rotors and pads even caliper on passenger side and rear brake pads but pedal still goes to floor


Did you bleed the brakes after doing all that stuff? You have to bleed em any time you remove the calipers

Jun 29, 2011 | 1999 Ford Explorer

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Brake pedal goes to the floor


check vacumn and\or connections to the vacumn boost cannister.

Apr 21, 2010 | 1985 Ford F150

5 Answers

Brake pedal goes to the floor only when engine is running. Pedal is perfect with engine off.


your power brake booster is blown out
the seal has a leak in it
run the truck for 3 minutes and shut it off. with the windows up listen carefully while you gently apply the brakes
listen for a hissing sound of air leaking.
the sound of these leaking is a very soft sound

Mar 27, 2010 | 1998 Chevrolet K1500

2 Answers

Changed front brake pads. brake pedal goes to floor. no brakes


Something doesn't sound right, you shouldn't have to remove the brake line to install pads. Did you have to do this on both sides? Do the new pads and the old pads look the same? Did you get the caliper on crooked? Just recheck your work first before replacing more parts. When you install the caliper, You have to hook the pad on one side first before you slide it over the rotor.

Mar 26, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1998 Ford Explorer Logo

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...