Question about 1998 Chevrolet Astro

Open Question

Lower intake manifold torque setting 2000 astro van 4.3 ltr engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: Looking for the torque specs for 1998 chevy astro van?

1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Posted on Dec 28, 2008

Ad
LT1Rob
  • 55 Answers

SOURCE: Torque Spec for '99 Chevy C1500 5.7L engine lower intake manifold

On 5.7L engines, install the bolts and torque in sequence as follows:

  1. Step 1: 71 inch lbs. (8 Nm).
  2. Step 2: 106 inch lbs. (12 Nm).
  3. Step 3: 11 ft. lbs. (15 Nm).
f2266b6.jpg

Posted on Mar 14, 2009

  • 462 Answers

SOURCE: 2001 astro chevy van 4.3 engines need to set the timing

The distributor in that engine can only be installed in one position. The hold down is built onto the distributor meaning when it is installed and the engine runs the computer is responsible for the timing. The distributor will move a little but won't correct major timing errors.

Posted on Sep 13, 2009

jimmybrown67
  • 835 Answers

SOURCE: what is the torque specs for a 2000 chevy vortec

tighten in 3 steps 1) 26in-lbs 2)106in-lbs 3)132in-lbs

Posted on Nov 02, 2010

ZJLimited
  • 17970 Answers

SOURCE: What is the torque spes

For 2004 Chevrolet Truck Silverado 2500HD 4WD 6.0L SFI 8cyl, the intake manifold, throttle body, fuel injection rail, and fuel injectors may be removed as an assembly. If not servicing the individual components, remove the manifold as a complete assembly.

Intake manifold bolts. Tighten intake manifold bolts first pass in sequence to 44 inch lbs. (5 Nm). Tighten intake manifold bolts final pass in sequence to 89 inch lbs. (10 Nm).


zjlimited_865.jpg

Fig. Lower intake manifold bolt tightening sequence - 4.8L, 5.3L and 6.0L engines

Hope this helps.

Posted on Mar 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Intake manifold torque specs 2000 olds silhoutte 3.4


Follow the link for a complete listing of this engines bolt torque specs. Torque Specs Database

Jan 25, 2017 | 2000 Oldsmobile Silhouette

1 Answer

2000 chevy v-6 4.3 torque sequence and settings for intake manifold


lower intake manifold

step 1 27 inch lbs.

step 2 106 inch lbs.

step 3 134 inch lbs.



johnjnail_54.jpg
upper intake manifold

step 1 44 inch lbs.

step 2 80 inch lbs.

Jun 01, 2011 | 2000 Chevrolet Blazer

1 Answer

Torque sequence for 1996 chevrolet van intake manifold with a 4.3 litre moter


Ha, you tried to fool me with the bit about a 3.5 L motor--I could find that one...here is the complete procedure from AutoZone.com:




Installation To install:
  1. Clean the gasket mounting surfaces. Be sure to inspect the manifold for warpage and/or cracks. If necessary, replace it.
  2. Position the gaskets on the cylinder head with the port blocking plates to the rear and the This Side Up stamps facing upward. Then apply a 3 / 16 in. (5mm) bead of RTV sealant on the front and rear of the engine block at the block-to-manifold mating surface. Extend the bead 1 / 2 in. (13mm) up each cylinder head to seal and retain the gaskets.

    0996b43f80208c7b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold tightening sequence-4.3L engines
  3. Install the lower intake manifold. Tighten the bolts in sequence and in 3 steps, as follows:


    1. Step 1: 26 inch lbs. (3 Nm).
    2. Step 2: 106 inch lbs. (12 Nm).
    3. Step 3: 133 inch. lbs. (15 Nm).

  4. Install or connect the following:

    Power steering pump Alternator bracket bolt near the thermostat housing Wiring harness to the lower manifold components, including the injector, EGR valve and ECT sensor Air conditioning compressor bracket-to-the lower intake manifold pencil braces
  5. Install transmission oil dipstick tube, if necessary.

    Fuel supply and return lines to the rear of the lower intake
  6. Temporarily reattach the negative battery cable, then pressurize the fuel system (by cycling the ignition without starting the engine) and check for leaks.
  7. Disconnect the negative battery cable.
  8. Install or connect the following:

    Heater hose to the lower intake Upper radiator hose to the thermostat housing Distributor assembly and engage the wiring Ignition coil Connect vacuum hoses to the upper and lower intake manifold. New upper intake manifold gasket, making sure the green sealing lines are facing upward Upper intake manifold Manifold retainers. Tighten them to 88 inch lbs. (10 Nm) using two passes. Purge solenoid and bracket Brake booster vacuum hose at the upper intake manifold PCV hose to the rear of the upper intake manifold Vacuum hoses to both the front and rear of the manifold assembly Throttle body Throttle linkage to the upper intake Wiring to the upper intake components including the TP sensor, IAC motor, MAP sensor and the fuel meter Engine cover Air intake assembly
  9. Connect negative battery cable.
  10. Refill the engine cooling system.
  11. Start the engine and check for leaks.

Aug 26, 2010 | 1996 Chevrolet Astro

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

1 Answer

Need to replace intake manifold how do you do this


Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

3.8L Engine
VIN 1 Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold
To install:
  1. Install or connect the following:
    Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

VIN K Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Relieve the fuel system pressure.
  5. Remove or disconnect the following:
    Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold

    a5adffa.jpg
    Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
To install:


140d431.jpg
Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine


4950e4f.jpg
Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine
  1. Install or connect the following:
    Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

Hope this help (remember rated this).

May 17, 2010 | 2001 Pontiac Bonneville

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

1 Answer

Starter for kia sportage 2000


  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter


    0900c152801b0603.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the starter

To install:
  1. Install or connect the following:

    Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

Jun 28, 2009 | 2000 Kia Sportage

1 Answer

Looking for the torque specs for 1998 chevy astro van?


1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Dec 28, 2008 | 1998 Chevrolet Astro

Not finding what you are looking for?
1998 Chevrolet Astro Logo

Related Topics:

489 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...