Question about 2005 Dodge Durango

Open Question

How to remove front axles from diff on 2005 dodge durango

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 82 Answers

SOURCE: How are the front disk brakes removed on a 2005 Dodge Durango?

when you have the caliper lossened sometimes you have to depress the caliper piston to get the pads out. Use a large flat head screw driver and pry the pistons back a little. Be careful not to pry too hard. Hope this helps.

Posted on Jan 13, 2009

Ad
  • 1 Answer

SOURCE: remove front axle from differential on 2003 dodge ram

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Posted on Feb 15, 2009

  • 4 Answers

SOURCE: front cv axle 1995 dodge intrepid

Naturally you need to remove the tire then the brake caliper. After the brake caliper is removed then you need to remove the 34mm axle nut that is inside the hub. After that is removed then you can remove the hub. Becareful not to damage the hub seal on the back or you will have to buy a new hub (100 or more). Then you need to remove the strut knuckle assembly. Once the knuckle assembly is removed then you can pull the CV axle. Take care the inner CV housing is held in place by an inner snap ring. You will probably have to pry off the inner housing. Once the axle is off then install the new axle (if you buy complete axle). Make sure if you are doing both that you take care which side you are installing. I made that mistake and double the work. Slide the new axle on the spline and make sure it is seated completely. Then put back together the reverse of removal.

Posted on Mar 24, 2009

  • 1 Answer

SOURCE: i cant get the axle out of the front diff what is

how do I get the front axel shaft off

Posted on Jul 13, 2009

  • 1 Answer

SOURCE: How do you remove the front shocks on a 2004 Dodge Durango 4X4?

how do you remove the front shocks on a 2004 durango limited 4x4. the stabilizer bar and axle links appear to be the way for removing the lower shock mounting bolt

Posted on Dec 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just put a tranny in my 2005 Dodge Durango and I can't get the front drive shaft to go back in. There is simply not enough room. How do I get it to go back in?


Hate to tell you this but the front drive shaft has to be put in before you completely install the front drive axle. Do this lift front of ground put jack stands under body loosen up the front drive axle to the point you can get the drive axle installed. Good luck.

Jul 28, 2015 | 2005 Dodge Durango

1 Answer

I have a 2003 dodge Durango. It's making a noise that sounds like a bearing that's going out. I've checked over the whole front end drive assembly and have narrowed it down to the front axle chunk. I'm...


drive the truck in a safe place turn left to right you will here a noise change from the left or the right the weight shift will indicate what side. fluid level should have a bolted plug either in the center of the diff or left or right side of it put pinky in first knuckle bend down if fluid on finger it is ok.

Mar 07, 2015 | 2003 Dodge Durango

1 Answer

How to take apart the front differentral of a 2005 dodge ram 4x4


remove the axles --- remove the drive shaft . If it is a Salisbury style diff remove the plate on the front and prise out the diff carrier (Crown wheel assembly ) Undo the pinion nut --remove the pinion and pull the pinion out the front. If it is a centre that is bolted in from the back then undo all the bolts around the cast housing and pull of that way.

Feb 17, 2014 | 2004 Dodge Ram 1500

1 Answer

Humming noise sounds like from the front end. I just replaced wheel hubs and still making noise. The tone of the humming changes with slight on off the gas pedal. I just ordered new front axles thinking...


check side carrier bearings in the diff i have rreplace a lot of them for the same noise thats all you have to do remove the diff cover remove end caps and see if the bearings are pitted if so replace

Jan 13, 2013 | 2000 Dodge Durango

1 Answer

I have a 2005 dodge durango 5.7 v8 mangum and the dodge manual was not included I was trying to figure out whether it was a 4wd or 2wd and mpg is


About 17 hwy, 12 city. As for the 2 or 4wd option simply look under the front of your vehicle. If you have a front axle you have a 4x4. Your fuel mileage will be the same with both options.
http://www.fueleconomy.gov/feg/bymodel/2005_Dodge_Durango.shtml

Nov 23, 2011 | 2005 Dodge Durango

1 Answer

Front and back berring dissassembly of differential 2001 dodge 1500


For the rear diff., remove the driveshaft, brake drums, diff. cover, remove pinion flange nut, move diff carrier to access side gear retainer bolt and remove bolt, slide side gear pin out and push axles in to remove axle retainers and remove axels. Mark carrier bearing retainers, spin bearing retainers to loosen carrier for removal. Remove carrier, remove pinion out of diff case, then r&r bearings. Any shims should be replaced in their original location for depth and pinion to ring contact.

Feb 05, 2011 | 2001 Dodge Ram 2500 Truck

1 Answer

How do you remove the front shocks on a 2004 Dodge Durango 4X4?


how do you remove the front shocks on a 2004 durango limited 4x4. the stabilizer bar and axle links appear to be the way for removing the lower shock mounting bolt

Apr 29, 2010 | 2004 Dodge Durango

1 Answer

Diff. Fluids for front & rear?


75w140 syn in both axles and 1 small bottle of additive per 1 liter of gear oil for rear axle

Aug 09, 2009 | 2005 Dodge Ram 3500

1 Answer

2005 Yukon Front Diff Axle seals


You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
2005 Dodge Durango Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...