Question about Cars & Trucks

1 Answer

Where is vacuum canister located on a 2000 ford expedition suv

A/c and heater will not blow into auto sounds like it's going outside

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,370 Answers

For exact location and diagram of vacuum canister on ford expedition,click the link below and view its diagram:----
Vacuum canister 2000 ford expedition

http://technoanswers.blogspot.com/2012/11/vacuum-canister-2000-ford-expedition.html

----------

These will help.

Thanks.

Posted on Nov 30, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75807 Answers

SOURCE: 2003 Ford Expedition Heater not working

This is all to common an issue in many Fords starting in the mid 90's, reason they went to a electric motor to control the air blend door , this motor moves the door air that diverts heat or cold from the AC, or mixes or blends it,the motor has failed or the door is stuck in the air duct, the bottom line is that to fix either problem the dash must be removed, no a job for the home mech, takes about 10-15 hrs to complete.

Posted on Dec 12, 2008

alicantecoli
  • 22133 Answers

SOURCE: Ford Expedition 2002 Front Heater blows cold air below 45 MPH

impeller is made of plastic on teh water pump and its slipping and spinning on the shaft renew before weather warms up as engine will overheat

Posted on Jan 01, 2009

  • 1 Answer

SOURCE: 99 ford expedition front heater core location

I have a coolant leak inside my expedition and it is coming through the vents does this mean that it is the heater coil

Posted on Jan 29, 2009

  • 1 Answer

SOURCE: 2000 Honda Odyssey Fuel Vapour Canister location

It is located at the top of the gas tank. You are going to have to drop the tank in order to check it, so it is best to do this when there is not a lot of gas in the tank. Hope this helps you out.

Posted on Aug 21, 2009

  • 1 Answer

SOURCE: heater blows cold air on my 2000 Ford Expedition

Have had the same problem 2000 ford expedition. got it working good now

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater in 2000 ford expedition is only blowing lukewarm.Had my core flushed and thermostat changed what to check next?


Make sure the coolant is full. Check it both cold and hot. The res bottle has lines on it. If it's full then the door between the outside fresh air and the heater box isn't closing all the way when you turn the knob over to hot. I'm not sure if this is Vacuum operated or electrical. Ford used to be all Vacuum but times are changing.

Oct 24, 2013 | Ford Cars & Trucks

1 Answer

2000 ford expedition no front heat, back heat work fine. I went through the glove box and into the side of the heater box, the blend door works fine. Any ideals?


if blend door works blower working check make sure you have enough coolant because suvs holds right much antifreeze.heater not working heater core plugged make sure both heater core hoses hot to touch if so problem could be temperature mode switch.

Jan 21, 2013 | 2000 Ford Expedition

1 Answer

1999 Expedition Keypad Reset


we have 2000 exped. and seller didnt know code. Heard that it is located in the rear of the truck where the bumper jack is... and i couldn't figure it out. Went to dealer...yikes!! and paid 50.00 to have it reset to factory. had to weigh fustration...locked in keys... and inconvience against my time of not figuring it out.... took 15 minutes at ford....

Nov 07, 2011 | 1999 Ford Expedition

3 Answers

2000 Ford Expedition My Expedition (4.6L V-9 2WD) has had an intermittent problem of cutting out. The Check Engine light was not coming on - so I figured it is not a misfire. It drove just like it had...


Continuous Memory Diagnostic Trouble Code (DTC) P0446 or P1450 indicates that Self-Test has detected the Evaporative Emission Control System has excessive fuel tank vacuum. Also, a DTC P0446 indicates a vent control malfunction.

Possible causes:

EVAP canister purge outlet tube (EVAP canister purge valve to EVAP canister) blockages or kinks.

EVAP canister tube (fuel tank to EVAP canister) blockages or kinks.

Fuel vapor elbow on EVAP canister contaminated.

Restricted EVAP canister.

Canister vent (CV) solenoid stuck closed (partially or fully).

Plugged or contaminated CV solenoid filter.

EVAP canister purge valve stuck open.

Fuel filler cap stuck closed (no vacuum relief).

VREF circuit open in fuel tank pressure (FTP) sensor.

Damaged FTP sensor. (fuel tank pressure)

Check for kinks or bends in the fuel vapor hoses/tubes (EVAP canister purge outlet tube and EVAP canister tube).

Visually inspect EVAP canister inlet port, CV solenoid filter and canister vent hose assembly for contamination or debris.

Check CV solenoid filter for blockage or contamination.

The common things I've seen are are mud in the canister and the canister vent solenoid being shot or the wiring to the canister vent solenoid being torn off. The resistance of the solenoid should be 48-65 ohms..
Pick up a Chiltons book and will give you a diagram of where exactly you find the canister. They are like $15 at any auto store. Good luck

May 22, 2011 | 2000 Ford Expedition

1 Answer

I have a 2000 ford expedition. what are the inner diameters of the heater hoses going thru the firewall


The hoses don't go through the firewall, they connect to the pipes of the heater core under the cowl in the engine compartment. The size should be marked on the outside of the hoses.

Mar 18, 2011 | 2000 Ford Expedition

1 Answer

I have a 2000 ford expedition and the heater blows air just not hot air or even warm air.. weve already changed out the thermostat, heater core, heater control valve and it still isnt working.. what could...


Check the vacuum hoses from the switch to the engine compartment. If you manually operate the heater valve on the firewall (follow the 5/8" hose) you will get heat.

Feb 08, 2011 | 2000 Ford Expedition

1 Answer

We have a 2000 frod expedition. We started to expirience that the heater would work then blow cold air. we replaced the thermostate then the engine would overheat. right after starting it would blow hot...


Try bleeding the air out of the system again. This truck has the radiator cap located lower than the heater core & upper hose and easily traps air pockets in it. It also helps to park on a slight incline and have a helper bring the rpm's up while "burping" the system.

Jan 08, 2011 | 2000 Ford Expedition

2 Answers

Heater blows cold air on my 2000 Ford Expedition


Have had the same problem 2000 ford expedition. got it working good now

Mar 03, 2010 | 2000 Ford Expedition

1 Answer

Ford Expedition won't stay running in cold weather


it could be many things it could be a bad EGR - valve are a vaccum leak or a bad fuel injection or engine control systems malfunction on my 2000- Expedition i replace the intake manifold itself and the gasket the best thing to do if its that is to get the whole thing from Napa with gaskets its not that hard to do go to your local library and get your hands on a Haynes auto repair manual for your SUV also give these websites a try www.alldatadiy.com and www.autozone.com wish you the best of luck and let me know what it was Michigan Man.

Jan 02, 2010 | 2000 Ford Expedition

1 Answer

The turn signals stopped working on my 1998 ford expedition. The high beams work when switched, as well as the wiper blades when turned on (full or intermitent). Is the problem the turn switch? If so,...


yes it sounds like your switch and its in the steering column try these websites www.autozone.com and www.alldatadiy.com if all fail stop by your local library and get your hands on a Haynes auto repair manual for your SUV i have one for my 2000 ford Expedition and it has help me out with a lot of things wish you the best of luck Michigan Man.

Sep 10, 2009 | 1998 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

429 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...