Question about 2006 Chevrolet Cobalt

Open Question

2006 chevy cobalt timing chain replacement

How to install 2006 chevy cobalt timing chain

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 2006 Chev Cobalt oil filter replacement

i have a 2006 chevy cobalt LT..and i just replaced my oil filter today!!! after several hours of looking i finally looked on the front side of the transmission block.to the left just below the air intake system is a hard heat resistant plastic black bolt topper.it is 1 1/4" in size..i bought a 1 1/2" size and a 36mm size socket torque wrench..both didnt work..1 1/2 was way too big, the 36mm was just slightly too big..took them back, replaced for the 1 1/4" inch socket and voila!!! is was rather difficult..you will need an extender and some good torquing to do to pop it..but once you do it will pop fine..oh, and you will need a 1/2" drive socket wrench.but the 1 1/4"inch socket..pop it onto a 1/2" drive socket wrench with the extender and you are good to go!!

Posted on Jun 10, 2008

  • 137 Answers

SOURCE: how do I replace my 2006 Chevrolet Cobalt Brakes

first loosen the road wheel nuts. then jack it up. then remove the road wheel. then turn the wheel out (brake side) get a g clamp put one end on the caliber and the other on the outside pad and wind nice and slowly then remove the two bolts holding the caliber and put aside DONOT TOUCH THE BLEEDING NIPPLE OR REMOVE ANY OF THE RUBBER HOSES ON THE BRAKE LINES open the reserveor (BRAKE FLUID CAP) the disk (rotor) look for a retaing screw on it and remove it some cars havem some dont then tap the disk off asemably is the reverse of removel

Posted on Jul 08, 2009

  • 124 Answers

SOURCE: Fan switch does not work in the 1, 2, 3, position 2006 Cobalt

You have a problem with the blower motor resistor. This is a very commen problem on all gm cars and light trucks. The part is not to pricey. You can find the resistor under the glove box buy the blower motor. Two bolts and out it comes.

Posted on Sep 14, 2009

  • 1 Answer

SOURCE: back seat removal of a 2006 cobalt coupe

are you trying to remove the cushion or the back rest?

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the cam sensor located on a 2006 cobalt 2.2


http://repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0996b43f/80/7c/be/01/medium/0996b43f807cbe01.gif
4_17_2015_6_40_53_am.jpg

Apr 17, 2015 | 2006 Chevrolet Cobalt

1 Answer

Remove and replace an outside door handle on a 2006 Chevy colbalt?


the following quote is taken from the web site from a chevy cobalt forum. if you have any more questions they might be able to help you directly.
(all it is is 2 bolts. Just take off your door panel and pull back the protective plastic and look for 2 bolts that line up with the door handle.)

How Do You Replace The Outside Door Handle Chevy Cobalt Forum Cobalt...

Jan 30, 2015 | 2006 Chevrolet Cobalt

1 Answer

Help! I was changing the water pump on a 2006 Cobalt and I dropped a socket into where the timing chain is...anyone else ever do this? Its not down in the oil pan, and I'm not really sure where it...


If it dropped into the timing chain cover, a long flexible magnet should help you retrieve the socket that was dropped. It will take some hunting but it can be done. Worst case is that you are going to have to remove the timing chain cover and get the piece out, if you do that make sure that you get the timing chain gasket to replace the gasket from the old one.

Jun 16, 2011 | 2006 Chevrolet Cobalt

2 Answers

How to set my timing on a 2006 chevy cobalt 2.2


There is no ignition timing to set on these later model cars. The spark is controlled by sensors and the engines computer which will pulse the injectors and ignition coils. What kind of problem are you having?

Nov 08, 2010 | 2006 Chevrolet Cobalt

1 Answer

Does a 2005 chevy cobalt have a timing belt or timing chain?


The 2005 Chevy Cobalt timing chain kit, Includes: Cam, Crank, Chain, Tensioner, Guide (3) and cost $134.

Oct 06, 2010 | 2005 Chevrolet Cobalt

1 Answer

Have a 2006 cobalt 2.2 liter DOHC eco tech w bad head gasket and warped head. just got the head machined and replaced the head gasket along with many other parts. but im trying to install the timing chain...


when you got the chain on and the cam's timed and unloaded and locked the tensioner and installed the tensioner then the shoe guides did you unlock the tensioner before you turned it over
when you turn the engine over it will have a little bit of slack because it's only spring tension
double check the engine is timed correct don't worry about the colored links they only line up every 35 revolutions
if the crank and the cams are in time
you should be good
hope this helps

Nov 08, 2009 | 2006 Chevrolet Cobalt

Not finding what you are looking for?
2006 Chevrolet Cobalt Logo

Related Topics:

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...