Question about Cars & Trucks

1 Answer

How do you get the hub assembly off the front axle on a 2007 kia sorento?

Posted by on

Ad

1 Answer

Remove & hang brake caliper,remove rotor,axle nut,
lower ball joint nut & swing steering knuckle out & off
drive axle

Then remove 3 or 4 bolts holding Wheel Hub Bearing on
from behind

Posted on Nov 30, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear bearings


As I said, all wheel bearings are replaceable. Remove the bearing cover, remove the split pin, undo the castleated nut, remove the hub. Push the bearing out from the rear. There is usually a small ring of bearing seat visible from the rear. I used to use a large socket with the extension bar and a good sized hammer with the hub on a block of wood.

Nov 24, 2015 | 2007 Kia Sorento 4x4

1 Answer

Can I replace rear wheel bearings only on my 2007 sorento [I realise I need to have them pressed in] or do I need to replace whole hub & bearing assembly its a solid axle type


Hub bearings are always replaceable using the existing hub. You only need to press them in by hand and then tap them in with a socket big enough to sit on the outer bearing race. Put the hub on the car, put the tire on the hub and tighten the hub nut whilst turning the wheel until the pressure on the bearing caused the wheel to lock up. Then back the bearing off by the required amount, usually a quarter turn. Check the manual.

Nov 24, 2015 | 2007 Kia Sorento 4x4

1 Answer

How to remove left front axle from 2007 kia sorento? the axle not the cv axle.


Hi there, one end will knock off and the othe may have a circlip holding it on, you will need to clean all grease of to find it properly, hope this helps.

Feb 14, 2015 | 2007 Kia Sorento 4x4

1 Answer

Hub assembly


The front hub is pressed into the wheel bearing You will have to remove the brake caliper and rotor and axle nut . install a slide hammer bang it off.

Apr 19, 2014 | 2007 Kia Amanti Sedan

1 Answer

Kia Sorento 2007:My windshield wiper stops on wrong side, what can I do?'.


If the wipers are consistent in where they stop the problem may be due to the splined shaft of the drive motor has rotated within wiper linkage attachment. Remove motor/linkage assembly remove linkage from motor and check for stripped splines on the linkage/motor. Willie

Jan 04, 2013 | 2007 Kia Sorento 4x4

1 Answer

Does not into 4x4


what type of kia a sportage or sorento if its a old sportage under 2000 you have vacume hubs in front and sometimes the locking hubs break you jack up front and check to see if they lock in 4x4 if its a sorento you have a transfer case motor and sometimes the motor burns

Jan 26, 2011 | Kia Sportage Cars & Trucks

1 Answer

My auto 4x4 isnt working in my kia jeep. is this a big job to get sorted?


This is a long/hard one to answer as a few things can cause this. First, check the vacuum lines running from the engine down to the front axles for cracks, and make sure you have vacuum to the axle hub. Second, remove and inspect the front wheel bearings, they should be set to proper preload and there should be no signs of water in the hub. And last if there is water in the hub, that most likely means there is rust on the front axle, and the pitting caused by the rust will not allow vacuum to build up and ingage the four wheel drive. the later requires a new front hub kit $$$.

Dec 01, 2010 | 2007 Kia Sorento 4x4

1 Answer

Oil filter 2008 sorento


I had a hard time finding it on my 2003 3.5L. You have to drop the plastic pan under the engine to get to it. On the 3.5L it is located at the left front corner the engine directly above the front axle frame.

Jun 22, 2009 | 2007 Kia Sorento LX 4x4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...