Question about Ford F-150

Open Question

2001 ford f150 ignition module location - F-150 Ford Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: ignition control module location for 1997 ford thunderbird?

1997 Ford Thunderbird Transmission problem
When driving normally transmission surges like it is not in gear. Had sensors replaced, nitural safety switch, and still acts up.

Posted on Dec 18, 2008

chuck943
  • 783 Answers

SOURCE: location of ignition control module

It does not have an ignition control module.
The electronic ignition (EI) for the 4.0L engine consists of the following components:
Crankshaft position sensor (CKP sensor) and 36 minus 1 tooth trigger wheel.
Ignition coil .
powertrain control module (PCM) .
Related wiring.
The PCM controls the firing of the coil based on the signal from the crankshaft position sensor.
The crankshaft position sensor (CKP sensor) is a variable reluctance-type sensor, triggered by a 36 minus 1 tooth trigger wheel configuration machined into the rear of the crankshaft vibration damper. The signal generated by this CKP sensor is called a CKP signal. The CKP signal provides the base timing and rpm information to the powertrain control module (PCM). Base timing is set at 10 degrees BTDC and is not adjustable.
If vehicle has no spark then turn key to on position,check engine light should come on.As you start cranking engine it should go out while cranking after about 10 secs. it should come back on(while cranking). If it come on then the PCM sees the signal,if it does not then PCM is not seeing it and this is your problem,either the CKP sensor or the wiring to it.

Posted on Mar 16, 2009

frankzen
  • 19 Answers

SOURCE: Where is the Ignition Control module located on a 1990 Ford f150

The ignition module is held on to the distributor by two 5.5mm bolts, but there is a tool for getting those bolts out. And you're right they are prone to failure.

Posted on Apr 04, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

moparownr
  • 667 Answers

SOURCE: firing order 2001 ford f150 4.6

the firing order is 1-3-7-2-6-5-4-8, cylinders are number right bank (passenger side) 1-2-3-4, left bank (drivers side) 5-6-7-8

Posted on Apr 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wheres the ingnition control module on a 2001 ford f150


With cop ignition, two wire ignition coil, ic control is in the pcm.
Voltage to the coil goes hot when you turn on the key, fuse protected. Your computer controls the coil ground circuit. I'm not sure about engine size?
ignition coil-dkww15fqtro1ypfgge5zegwe-4-0.jpg

Mar 06, 2017 | Ford F-150 Cars & Trucks

1 Answer

Ignition control module location on a 1992 Ford Truck F150 1/2 ton P/U 2WD 4.9L FI 6cyl


I believe it is mounted on the distributor.. It is bolted onto the distributor with two small screws. It is called a TFI Module (Thick Film Integrated) module. It is gray in color and about 1 inch wide maybe 3 inches long with a connector on one end.

Jan 30, 2013 | Ford F-150 Cars & Trucks

1 Answer

How to replace ignition control module on a 1994 ford f150


Depending on your engine, if its located on the distributor remove the two screws/bolts that secure it pull downward to take it off, then slide the new one upward and put your screws/bolts back in, if you have the ignition module on the driveside fender same instructions.

Jan 19, 2011 | 1994 Ford F150 Styleside Supercab

1 Answer

I have a 2001 ford f150 5.4 v8. I shut it off and when I tried to restart the truck it would crank over fine but not start. starter turns fine and there's plenty of fuel. Truck ran fine prior to failing...


Check fuel injection. Could be a fuse or module. Also check to see if fully in park or in neutral.
Most likely electrical side of ignition. Since plugs, cap and wires are out of the way, it is most likely in the fuse panel.

Jan 04, 2011 | 2001 Ford F150 Styleside SuperCrew

1 Answer

I have a 2001 Ford F150. It turns over but will not crank. Tried to jump it off but will not start. Gages and lights work inside. What does that sound like to you? Someone mentioned a fuel pump module....


That may be the problem, you would have to do one thing to make sure and that spray starting fluid into the throtle and if it starts for a few seconds then i would say its the fuelpump module, a fuelpump module is a unit with the fuelpump and preasure sensor and sending unit as one i will show you a picture, this unit is located inside the gas tank the tank will need to be dropped in orderto install the pump module, in goes in on top of the tank after tank is removed,johnjohn2_15.jpg

Nov 08, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Location of ecm on f150 2001


Powertrain Control Module (PCM) Removal and Installation
  1. Disconnect the battery ground cable.
  1. Disconnect the powertrain control module (PCM) electrical connector.
bb45a1b.gif


Remove the right front door scuff plate.
bb7fcba.gif


  • Remove the right cowl side trim panel.

  • 33976d7.gif

  • Remove the clip and remove the PCM.

  • 6269f6f.gif

  • To install, reverse the removal procedure


  • Hope this helps ya.. :-)
  • Jul 21, 2010 | 2001 Ford F150 Styleside SuperCrew

    2 Answers

    Wont start or has problems starting


    Chek fuel filter first, and replace if it hasn't been changed in a while. Then if it still has problems starting, check ignition module. Make sure all grounds are tight and making good contact as well.

    Aug 19, 2009 | 1990 Ford F150

    1 Answer

    Ignition module location


    IT SHOULD BE ON THE DRIVERS SIDE FENDER, THE MODULE SHOULD BE A SILVER OR GRAY BOX WITH A COUPLE OF PLUGS ON IT, THE BOLTS THAT HOLD IT TO THE FENDER WILL NEED TO BE ACCESSED FROM INSIDE THE WHEEL WELL. THIS STYLE IGNITION CONTROL MODULE IS FAMOUS FOR GETTING HOT AND JUST TURNING OFF LEAVING YOU STRANDED, IN MOST CASES THE VEHICLE WILL RESTART AFTER THE MODULE HAS TIME TO COOL OFF.

    Jun 14, 2009 | 1991 Ford F150

    3 Answers

    Where is the Ignition Control module located on a 1990 Ford f150


    The ignition module is held on to the distributor by two 5.5mm bolts, but there is a tool for getting those bolts out. And you're right they are prone to failure.

    Apr 04, 2009 | 1990 Ford F150

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    283 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75077 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5471 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...