Question about 1991 Eagle Talon

2 Answers

Still cutting out

I got the idle problem fixed it was the i beleave its called a biss screw but still cutting out at around 2500-3000 untill 4000 anyone know

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I was haveing the same prob and i had cracks in my ex moanifold and turbo ex housing

Posted on Jun 19, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Could be associated with ur turbo, "boost lag" have u turned up your boost latly?? the talon stock turbo is only good for 12-14 psi 14 max any higher and it sounds very bad on the motor

Posted on Apr 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Iddell high


Check for vacuum leaks, disconnected hoses, etc. Then adjust the BISS (Base Idle Speed Set Screw). Follow this guide.

1G BISS Adjustment

Jan 11, 2014 | 1991 Eagle Talon

1 Answer

Hello I have a 1980 Ford Bronco 351 2bbl. Wondering if anyone knows which screws adjust what? Please if anyone has any ideas please respond. Thank you.


Here are some images that might help to assist you, and let me know if you require any further assistance.


Adjust the curb idle with the engine warmed up and the choke off.

421d8f7.jpg


The air/fuel mixture screws should be adjusted with the engine warmed up and at normal idle speed, then turn each air/fuel mixture screw in one at a time until the engine just begins to mis-fire, then back the air/fuel mixture screw out 1-1/2 to 2 turns out a half a turn at a time until the engine idle is the smoothest. (your vehicle might have restrictor caps over the air/fuel mixture screws to limit the amount of adjustment)

ae2024e.jpg

c7d3537.gif


The choke adjustments;

e992a23.jpg

f0f726f.jpg


To adjust the vacuum tension pull on the choke pull-off:

71de89e.jpg



Adjust the fast idle screw to the proper RPM with the engine cold and the choke on.

cadcd19.jpg

Jul 31, 2010 | 1981 Ford Bronco

2 Answers

My 1996 eagle talon tsi (just bought) idles rough but when I drive its smooth, no rough idle. I need to know what is wrong with it and how to fix it


It may be a dirty air cleaner or a dirty Idle Airflow Valve . The IAC can be cleaned by taking off the duct work that goes from the air assembly to the fuel injector hole. The valve is to one of the sides of the hole just inside. You will see two small holes. Buy some card cleaner and with your engine running at about 1300 rpm spray the cleaner directly into these holes. Spray for a good 10 seconds. Stop the engine and let the cleaner soak in. Repeat this about 4 times. If it still idles rough it may be the Idle position sensor or you have to replace the IAC.

Nov 20, 2009 | 1996 Eagle Talon

1 Answer

Motor bogs and wants to die when i stop with the a/c on.


What it sounds like you need to do, is adjust your BISS screw, its a little screw usually covered by rubber, sometimes not, it sits on top of your throttle body, and it adjusts how much air your car sucks when its at idle, if you adjust it for more air while idling, it should fix your problem that you described. You can use a flat head or a philips screw driver to turn the screw.

Jul 13, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

My 2004 ford escape limited when sitting idle @ a light or just sitting it **** then cut off. i replaced the idle air control & the mass air flow & it is still doing the same thing


BRING IT TO AN AUTO PARTS STORE THAT CHECKS CODES ON THE PCM FREE OF CHARGE. CALL AROUND FIRST AND THIS SHOULD GIVE YOU A BETTER IDEA OF WHAT IS HAPPENING WITH YOUR VEHICLE. DON'T FORGET TO ASK THEM TO CHECK PENDING CODES AS WELL. HOPE THIS HELPS. LET ME KNOW. WE CAN GUESS ALL DAY LONG BUT UNTIL WE HAVE THE FACTS, WE WILL NEVER REALLY KNOW. THANKS FOR USING FIX-YA.

May 07, 2009 | 2004 Ford Escape

3 Answers

Mitsubishi idling problem!!??


Am not shure the kind of engin you really have but see if your stepping mottor is damage or need relpacing. that problem can happen if you have a faulty unit . it also called the step up unit or sensor, if your car have air condition is turned on and the rpm goes up and down that can be the problem , the unit can be found attached to the throttle body. just below.

Mar 07, 2009 | 2002 Mitsubishi Lancer

1 Answer

Mitsubishi libero idling funny!!??


Do you have a check engine light on?

Mar 07, 2009 | 2001 Mercury Cougar

1 Answer

Can anyone tell me how to fix this problem


if its a carb model you might need to strip and refurb the carb if not buy a second hand one they are pretty cheap or it could be a choke problem

Feb 14, 2009 | 1988 Honda Accord 4 Door

Not finding what you are looking for?
1991 Eagle Talon Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Stewart Dibbs

Level 2 Expert

267 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...