Question about Cars & Trucks
Nris also have to pay tax in india if they are earning money in india
Posted on Nov 30, 2012
The interest earned on the fixed deposits is considered as income and bank is required to deduct tds on it. If ur father's total income is less than exemption limit then he can submit form 15h and tds will not be cut. See http://www.makemyreturns.com/income-tax-efiling/nri-taxation-services.aspx for more details on how to avoid tds
Posted on Nov 30, 2012
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Bank 1 & 2 running lean
The lean condition is caused from the upper intake gaskets and isolation bolts not sealing properly due to time and poor sealing qualities from the factory ther was a service bulliten for this through ford to replace the gaskets,bolts,vaccum line,and lh side valve cover for this concern the oil was getting onto the rubber contaminating it causing a vaccum leak. If you never had the tsb done i would start there, also if there is high milleage on the vehicle i would also clean the maf sensor and resedt kam.
Posted on Dec 04, 2008
bank one sensor 1 is the bank of cylinders that number 1 spark plug is located in, bank 2 the other side, this assumes u have a V8, the sensor one location is the sensors that are BEFORE THE CATALYTIC CONVERTER, the sensors referred to as sensor 2 are after the ones AFTER THE CATALYTIC CONVERTER IN THE EXHAUST SYSTEM.
Posted on Apr 28, 2010
Grand Cherokee oxygen sensor locations for 4.0
and 4.7 engines
Four wires (circuits) are used on each O2 sensor:
O2S Sensor removal Never apply any type of grease to the oxygen sensor electrical connector, or attempt any soldering of the sensor wiring harness.
WARNING: THE EXHAUST MANIFOLD, EXHAUST PIPES AND CATALYTIC CONVERTER(S) BECOME VERY HOT DURING ENGINE OPERATION. ALLOW ENGINE TO COOL BEFORE REMOVING OXYGEN SENSOR.
1. Raise and support vehicle.
2. Disconnect O2S pigtail harness from main wiring harness.
3. If equipped, disconnect sensor wire harness mounting clips from engine or body.
CAUTION: When disconnecting sensor electrical connector, do not pull directly on wire going into sensor.
4. Remove O2S sensor with an oxygen sensor removal and installation tool.
02S Sensor installation
Threads of new oxygen sensors are factory coated with anti-seize compound to aid in removal. DO NOT add any additional anti-seize compound to threads of a new oxygen sensor.
1. Install O2S sensor. Tighten to 22 ft. lbs. (30 N·m) torque.
2. Connect O2S sensor wire connector to main wiring harness.
3. If equipped, connect sensor wire harness mounting clips to engine or body. When Equipped: The O2S pigtail harness must be clipped and/or bolted back to their original positions on engine or body to prevent mechanical damage to wiring.
Hope thats help (remember comment and rated this).
Posted on Apr 29, 2010
Tips for a great answer:
Feb 16, 2017 | Cars & Trucks
Oct 20, 2016 | Cars & Trucks
Apr 14, 2016 | Cars & Trucks
Jun 16, 2014 | 1999 BMW 318 ti
Dec 20, 2013 | Cars & Trucks
Aug 28, 2013 | Cars & Trucks
Nov 13, 2012 | Cars & Trucks
Apr 14, 2012 | 1999 Ford Taurus
194 people viewed this question
Usually answered in minutes!