Question about Toyota Cars & Trucks

Open Question

Adjust headlights on a 2007 toyota sienna

Headlights shine too low

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2006 Pontiac G6-GTP How do I adjust the headlights.

to raise you headlights there is a small brass allen screw located above each headlight under the hood. to raise your headlights turn clockwise until they reach the desired level.

Posted on Oct 23, 2008

  • 36 Answers

SOURCE: headlights need adjusting

The headlights will have small rods or adjusting screws located near the headlight mounting points. Will probably need a torx socket or screwdriver to adjust. Torx is a 6 point type screw.

Posted on Mar 11, 2009

  • 1986 Answers

SOURCE: i replaced the headlight assemblies with eagle eye

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 06, 2009

  • 4793 Answers

SOURCE: 2001 VW Jetta Headlight adjustment. Headlights

sometimes the headlights stick to the adjusters,just pull/push(wiggle it)to free it, then try setting beams.

Posted on Apr 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlights do not work high or low beam all other lights work


Re: Condensation in Sienna Right Headlight.... - Toyota Sienna Forum

www.siennachat.com/.../4606-condensation-sienna-right-headlight.html
Mar 10, 2009 - 15 posts - ‎9 authors Over the years, I was not a frequent visitor to SiennaClub...but when I did visit, it was... in the right, passenger-side xenon HID headlight of my 2004 Sienna...the light has... Check with your dealer and see if they can do anything about it. .... :o The HID bulb is also a PITA to remove because you are working ... Re: 2004 Sienna no brake lights, radio, heater/AC ...
15 posts
Jan 4, 2013
Thread: HELP: Both Low Beams don't Work
6 posts
Nov 27, 2011
Thread: 2000 sienna drl and/or headlight issue
5 posts
May 7, 2010
Automatic Headlight Option: Useful or Not?
8 posts
Mar 3, 2010
More results from www.siennachat.com

Toyota 2004 Sienna repair: Replacing HID ballast or ...

toyotarepairsemipro.blogspot.com/.../replacing-hid-ballast-or-computer....
May 1, 2010 - Replacing HID ballast or computer control lighting for the Headlight. Just got a ... Up until now, I did not know I had the option of seeing twice as far with Xenon. Also up to ... In the end after buttoning everything up, the light did work fine. .... Howdo you determine if you have a HID or non-HID light? Reply ...

Oct 15, 2015 | 2004 Toyota Sienna

1 Answer

Is there a 12V output from integration relay going to headlight switch of 98 sienna LE. no headlight both hi and low, but flash headlight is working.


There is a fuse for both the low and high beam headlights.
There is a relay for both as well.

The headlight switch feeds the relay.

Thank you the excellent symptom of the problem.

Yes,12 V. goes to the headlight switch.

Mar 09, 2013 | 2000 Toyota Sienna

1 Answer

How do I adjust the headlights on a toyota sienna van 2005? Thanks


If your talking about the vertical alignment, there are setting screws on the back of the headlight assy. It looks like a 1/4" head bolt with a straight slot in in it and a 3/4" wide black or grey large serrated plastic washer under the head of the bolt.
Thanks,
Lee

Nov 13, 2010 | 2006 Toyota Sienna

1 Answer

High beam adjustment, how do you do it seams mine are reaching for the stars thaks john in wisconsin


two screws on each headlight control the direction the headlights are aimed. One screw, usually at the top but sometimes below the headlight, adjusts the headlight up and down. The other screw, located to one side, controls the headlight from right to left. Turning the appropriate screw one direction or the other will change the direction the headlight points.
In order to aim your headlights you need to have a flat vertical surface you can aim your headlights at in front of a level surface on which to park the car. If your driveway is level your garage door is the perfect place to aim your headlights.
The tools you will need for this job are simple. Masking tape is used to mark where the headlights are to be aimed and a screwdriver is needed to adjust the headlights. A tape measure will be necessary to measure the distance of the vehicle to the surface you're using to check the aim and to measure the up and down distances from your marks.
To start you will want to pull your car quite close to the surface you are using to aim your headlights. This is done to allow you to mark, with the masking tape, where the headlights are on the car. With the car right up against the vertical surface, and your low beam headlights on, the center of the beams will be directly in front of the headlights. Use your masking tape to mark straight across where the headlights are shining. Use short pieces of masking tape to mark vertically the center of the low beams.
, back your car about 25 feet away to check the alignment of the headlights. The brightest spot on your low beams should be about two inches below the masking tape and slightly to the right of the vertical marks. Use the adjustment screws to move the beams up and down, and right and left, until the headlights are aimed properly.
If your car only has two headlights, that's all you need to do. With the high beam lights integrated into the single headlight there is no further adjustment possible. If you have a four-headlight system you will next need to adjust your high beams. Switch to your high beams and adjust them so they shine just below the line and are centered between your two vertical marks.

good luck

Nov 05, 2009 | Volkswagen Jetta Cars & Trucks

1 Answer

HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 06, 2009 | 2001 Hyundai Tiburon

1 Answer

2003 Toyota Sienna Vertical Adjustment


should be adjustment under hood look for place where phillips screw driver goes in and meshes with the lenses to adjust it

Dec 27, 2008 | 2003 Toyota Sienna

1 Answer

2006 Pontiac G6-GTP How do I adjust the headlights.


to raise you headlights there is a small brass allen screw located above each headlight under the hood. to raise your headlights turn clockwise until they reach the desired level.

Oct 13, 2008 | 2006 Pontiac G6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...