Question about Hyundai Motor 2004 Sonata

Open Question

2004 huyndia sonata removal of glove box

Trying to replace fan resister for speed control of motor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 21 Answers

SOURCE: replacing heater switch in 2004 hyundai sonata

Open the ashtray, and grab the bottom of the bezel. Its only clipped in, so give it a yank and the bezel will come off. Unplug the connectors and replace your switch.

Posted on Jul 02, 2008

mastertecmec
  • 42 Answers

SOURCE: blower fan

Sounds like the problem is more with the blower motor assembly itself. The blower motor have micro-proccers built itnto them which comunicate with the control heads and do the actual regulating of the fan motor. Dealers have computers with diagnostic software which allows them to monitor what is happening in the eletronic controls of the vehicle. Electronic diagnostics without the diagnostic software makes it very diffecult to pinpoint the actual item causing the problem.

Posted on Jan 25, 2009

SOURCE: 2006 Hyundai Sonata 3.3 engine - cabin filter replacement

It should be the same general procedure as the 02. Open Glove box and remove contents. Remove glove box stops and or glove box shock on side. With the glove box swung out of the way remove the panel that covers the air filter. Remove and replace filter. Reinstall cover, and glove box stops.

Posted on May 10, 2009

  • 69 Answers

SOURCE: Removal of Radio in 2004 Hyundai Sonata

Remove the facia plate, and remove the 4 screws that hold the radio in place. It's actually one of the simplest cars you can do.

Posted on May 27, 2009

ZJLimited
  • 17970 Answers

SOURCE: Where is speed senor on a Hyundai Sonatas

Hyundai VSS locations:
On 1999-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

On 1996-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

On 1999-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

Hope helps (remember rated this).

Posted on Jul 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the resister located


on the firewall close to the blower motor usually

Feb 29, 2016 | 2010 Ford F-150

3 Answers

My fan blower motor only works on high,They say it maybe the resistor may be bad, where is it ? Thanks, Jim


Hi, the resistor is screwed to the side of the blower housing behind the glove box. See procedure below to replace the resistor. You don't have to complete all steps in the procedure. just work your way to the point that you can unscrew the resistor. Please let me know if you have questions, and thanks for using FixYa.

1990-93 Accord

See Figures 2, 3 and 4
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support)

jturcotte_1481.gif

Fig. Fig. 2: Remove the glove box and frame

  1. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.

  2. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly.
jturcotte_1482.gif

Fig. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully


jturcotte_1483.gifjturcotte_418.jpg

Apr 04, 2011 | 1993 Honda Accord

2 Answers

My blower only works on high is it the switch or resister


That is usually caused by the resistor module for fan motor speed control. Replacement is quick and not very costly

Apr 02, 2011 | 2004 GMC Canyon

1 Answer

The heating and air conditioning fan only works on the highest speed position. What would cause the lower speeds not to work?


If the system is a Manual ( not the EATC / Electronic Automatice Temperature Control System ) it is most likely the blower motor resistor.

For the new body style 2004 ( not the 2004 Heritage or Lightning models ), it is behind the glove box.
Open teh glove box, press on one side, to allow the glove box to hang down.
The Blower motor resistor is located in the side of the blower motor housing.

ea44d96.jpg

If your 2004 is a Heritage or Lightning, the blower motor resistor is access from under the dash / glove box area.
7e8c043.jpg

On this type ( same as the 97-03 ) the blower motor resistor or the resistor and pigtail might need to be replaced.
452e89b.jpg

Just pay attention to which body style 2004 you have ( new like the 2005-2008 or the 2004 Heritage / Lightning, which looks like the 97-03 MY trucks.

Aug 09, 2010 | 2004 Ford F150

3 Answers

AC & Heater Fan on fast spped only


Most of the time this is a bad "blower motor resistor". It is easy to replace. You will find your behind the glove box in the ac/heater (evaporator) housing. Below is a pic of the resistor as it is seen from behind the glove box. 1. resistor assembly. 2. harness 3. fasteners (2). 4. lower edge of glove box. (open).

f527558.gif

Jun 11, 2009 | 2002 Chrysler Town & Country

2 Answers

F150 2004 blower working only on high position.


this is because your blower motor resisters are burned out for speeds 1,2 & 3. High speed does not have a resister.

Replace the resister. If it goes a 2nd time, it is because your blower motor is failing & drawing too much current.

it is behind the glove box I think. It is in the plenum case where air blowing on it keeps it cool.

Easy repair. May need to access throught glove box which should open all the way down when you squeeze the sides in.

Go to tascafordparts.com for a discounted resister.
Please rate as solved problem if this is what you needed.

------------------------------------------------------------------------------
Manual Climate Control System Outputs
Blower Motor Switch Resistor
Blower Motor Resistor Coils 9ba1105.gif Blower Motor Thermal Limiter 47afe58.gif The heater blower motor switch resistor has the following features:
  • The assembly is located on the passenger side of the plenum assembly behind the glove compartment (06010).
  • Three resistance elements are mounted on the resistor board to provide four A/C blower motor speeds.
  • Depending on the heater blower motor switch position, series resistance is added or bypassed in the A/C blower motor circuit to decrease or increase A/C blower motor speed.
  • An overheating protective device (thermal limiter) will open the resistor coil circuit when the temperature reaches 121°C (250°F), interrupting the blower motor operation in all speeds except HI.
  • The thermal limiter cannot be reset and is not serviceable.

Mar 23, 2009 | 2004 Ford F150

1 Answer

2004 dodge stratus fan motor housing


Hi my name is Allen!

The Blower Resister is located on the passenger side. You will need to remove the silencer pad below the glove box, not behind but below the glove box. The resister is located on the bottom of the A/C Housing next to the blower motor. If you get the resister from the Dealership you will need to make the hole larger that the resister fits into because it has been redesigned and is to large for the whole. Also you will want to replace the blower motor also because the resistance build up inside the motor is what damages the resister.

If you need further asistance you may contact me through FixYa!

Dec 27, 2008 | 2004 Dodge Stratus

2 Answers

Front blower motor doesn't work, rear does


yes, all blower motors have them to control their speed, High, medium, low.. etc. I earn nothing by helping you, but my rating, a fixya rating and I will walk you through this

Dec 20, 2008 | 2005 Chrysler Town & Country

1 Answer

The heater / ac blower only works on high. It is not the blower or the control switch or the blower motor relay. Please help. Thank George


It is the blower resister. I purchasted one at auto zone for $18.00. It is located under the passenger side dash. You need to remove the glove box and the plastic cover under the dash to expose the blower motor. the blower motor resister is right next to the motor. Simply unplug the resister remove the two screws and replace. I did this and now my fan works on all speeds.

Jul 20, 2008 | 2001 Oldsmobile Alero

Not finding what you are looking for?
Hyundai Motor 2004 Sonata Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...