Question about Cars & Trucks

Open Question

Correct tension for a 2006 nissan navara serpintine belt

Hi could you advise me how to tell the correct tension for a serpintine belt for a 2006 navara d40 2.5 turbo diesel regards jim

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: Nissan 2006 navara 4x4 does not engage and AB warning light stea

check your ABS sensors.... sometimes they can get dirty and not read the wheel right.... that might fix you ABS solution.... and possibly your 4x4 it doesnt want to engage in 4 wheel cause of the abs

Posted on May 06, 2009

Ad
smartr10U
  • 1305 Answers

SOURCE: cant find drive belt tensioner bolt to loosen serpintine belt

The serpentine belt tensioner / pulley is on the front of the engine, and part of the belt 'routing'.

Its job is to put tension on the belt as it drives the other devices like the power steering pump, water pump, air conditioning compressor.

It is an aluminum casting that mounts with a single bolt to the engine. The pulley is attached to the arm.

There are a few ways to move / pry the arm inwards, thus releasing the tension on the belt for removing/installing: grab on the pulley bolt (15mm?) with a wrench, or some later models have an opening for a 3/8th socket wrench to attach to directly without a socket.

Posted on May 10, 2009

  • 34 Answers

SOURCE: 2006 volkswagon timing belt jetta tdi turbo diesel

i can walk u through doing a t belt. But if u are not sure if u are able to do it DO NOT DO IT cause if u are wrong if cause a lot of engine damage.

Posted on May 11, 2009

  • 484 Answers

SOURCE: 2006 Nissan frontier 4 cylinder belt diagram + tensioner pulley

They are under the hood or on the front crossmember.

Regards,
matt

Posted on Sep 14, 2009

  • 474 Answers

SOURCE: Hi we bought a Nissa Navara 2008 D40 4wd dual cab,

are you sure the correct amount of oil is in it? if over full the engine is trying to drag the crank shaft through the oil

Posted on Nov 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to copy the old keys information to new blank key for my Nissan Nissan navara outlaw 2006, which tool and where i can get it ?


Hi you need a main dealer or an Autolock Technition the required equipment will cost big bucks. Regards Jim...

May 05, 2015 | 2006 Nissan Navara 2.5

1 Answer

After replacing a timing belt on a 2006 mitsubishi galant, there is a whining noise at 1200 rpm. I've replaced the timing idler pulley, balance tensioner pulley, and the hydraulic tensioner pulley and now...


The fan belt is probly worn or dirty. Try cleaning the underside or the pullys in the serpintine route............or u mite hav to go back and chec work on the timing belt is all torqued to specs. Is belt tension rite

Jul 18, 2014 | 2006 Mitsubishi Galant

1 Answer

How to change belt


there is a tensioner on the motor that keeps the belt tight on the arm of the tensioner there is a half inch squre hole insert an half inch drive ratchit take the tension of the belt and **** it off the pully remove the belt and install new one if you dont have a diagram of the belt routing on a peise of paper draw the routing before removal

Jun 09, 2012 | 2005 Nissan Pickup Navara

1 Answer

Cranksensor trouble on nissan navara 2006


there is almost no way to miss align the flywheel! did you checked side by side for proper fit and all the slots matched , if you didn't i would get one fro the same place and match the old one, Also did you remove the sensor before replacing the flywheel? if you didn't you may have a broken sensor.

Apr 07, 2012 | 2006 Nissan Navara 2.5

1 Answer

I 2005 nissan navara outlaw, there are 79500 miles on it, at how many miles does the timing chain need serviced or changed?


It is usually the timing chain tensioner that malfunctions. However if you have a timing BELT it should be replaced between 75-80k miles.

A chain driven system will typically outlast the engine itself if everything is in a good order.

However there was a recall on some frontier engine's timing parts, you may want to have your VIN checked at a local dealer to ensure your engine doesn't qualify for the TSB repair.

Feb 09, 2011 | 2006 Nissan Pathfinder

2 Answers

The sepintine delt is loose. How do you adjust


More than likely the belt has stretched, replace this first. It could also be the tensioner... Look at the tensioner and see if it seems to jump alot with the engine running.

Jan 24, 2010 | 2006 Jeep Liberty

1 Answer

2006 Nissan frontier 4 cylinder belt diagram + tensioner pulley


They are under the hood or on the front crossmember.

Regards,
matt

Sep 14, 2009 | 2006 Nissan Frontier

1 Answer

2000 WINDSTAR VAN SERPINTINE BELT TIGHTENING


the belt is tensioned by an automatic belt tensioner pulley assembly, so what is the problem with the tension? belt noise?

Jun 09, 2009 | 2001 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...