Question about Honda Cars & Trucks
The check ingene came on i getting the code p301 and p034 and p0300 please hell.
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
P0420 relates to the catalytic converter. The computer sees little or no improvement in the exhaust before and after going through the converter. Either your oxygen sensors need replacement (3 total) or you need a new catalytic converter.
What is the mileage on the vehicle? Does it run well? Oxygen sensors generally start to fail after 70,000 miles. Catalytic converters usually fail because the engine is runnig rich and the owner ignores that fault for months. This causes the catalytic converter to overheat and fail.
P1456 relates to the evaporative emission system. This system holds the gas fumes in the system so they are not vented to the atmosphere. The most common cause of this code being set is failing to properly tighten the gas cap after refueling. Take the cap off and clean the sealing O-ring. Put it back on and tighten till it clicks 3 times. Make sure you have the correct gray colored gas cap. Clear the code and see if it resets within a few days. If it does, try replacing the gas cap.
Posted on Jun 26, 2008
Here is a good site for OBD II trouble codes. P0300: Random/Multiple Cylinder Misfires Detected, P0301: Cylinder 1 Misfire Detected, P0304: Cylinder 4 Misfire Detected.
Posted on Jan 25, 2009
P1320 Ignition Signal
Signal wire from distributor
P0325 Knock Sensor 1 Circuit Malfunction (Bank 1 or Single Sensor)
O2 senor ( The one before the cat converter )
P0300 Random/Multiple Cylinder Misfire Detected
The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we have either multiple cylinders misfiring, or the computer simply can't determine the specific cylinder, and as such we are left with the P0300 in computer memory.
Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect fuel pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues
Posted on Apr 13, 2009
P0300 Random Misfire Detected
P0301 Cylinder 1 Misfire Detected
P0302 Cylinder 2 Misfire Detected
P0303 Cylinder 3 Misfire Detected
according to this fault codes first mark ignition coils
3 ---------------- 6
2 ---------------- 5
1 ---------------- 4
this right banks and left bank, please remove Ignition coils with lids and spark plugs from right bank and swap with left bank, if fault code change as
P 0304 Cylinder 4 Misfire Detected
P 0305 Cylinder 5 Misfire Detected
P 0306 Cylinder 6 Misfire Detected
You can Identify it's a faulty ignition system then next swap ignition lids from ignition coils be careful each coils have two lids one short and other long bit deference and when you remove and fix it to the car keep in mind correct order because each coil two different fire for two spark plugs don't mix up, if you mix it can create the fault code.if you detect any fault ignition coils or spark plugs or lids replace that and also whether god or bad recommend to replace spark plugs, find the right that's most important thing, if this way couldn't found the any ignition fault next step is check fuel presser, when the engine running fuel presser must be around 4.5 bar without engine running must be 4 to 6 bar if the fuel presser too low need to check two different things one is fuel pump other is fuel injectors, in this case you can swap injectors from right bank to left bank and find is the injectors leaking, if not leaking faulty fuel pump.is this information helped you? if yes please leave a comment,
Posted on Oct 16, 2010
Tips for a great answer:
May 23, 2015 | 1998 Honda Civic EX
May 23, 2015 | Cars & Trucks
Nov 22, 2012 | 2000 Honda Odyssey
Jul 30, 2012 | 2009 Toyota Sienna
Aug 20, 2011 | 2002 Honda Odyssey
Jul 10, 2011 | 1999 Dodge Grand Caravan
Mar 16, 2011 | 2004 Dodge Ram 1500
Jun 01, 2010 | 1999 Cadillac Eldorado
Jan 25, 2009 | 1999 Toyota Camry
44 people viewed this question
Usually answered in minutes!