Question about Cars & Trucks

Open Question

1996 ford e250 4.9l squeal from crank pulley

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1996 jeep grand cherokee limited v8

I might not have enough information but the squeal is most likely a worn bearing. Try to isolate it with a "mechanic's stethescope" to locate the source. A pin point shot of WD-40 at the whining bearing (NO NOT put it on good bearings should TEMPORARILY quiet it IF it is a bearing. DO NOT overspray, just at the center of the pulleys...the lubricant should get pulled into bearing to confirm that the pump (power steering would be my guess) needs replacing.

Posted on Jan 09, 2009

Ad
kahuzlefitz
  • 4 Answers

SOURCE: 1996 jeep grand cherokee limited v8

Look at the pulley coming off the crank shaft. If the thrust bearing is going bad or is bad you will have excessive play in the crankshaft that causes excessive deflection of the belt. If it's this your looking at an engine rebuild. Just went through this on my dads jeep.

Posted on Nov 22, 2013

  • 9 Answers

SOURCE: My 2005 grand am is squealing badly, replaced idle pull didn't work, could crank pulley or water pump pulley be causing it

There is a spay can available at auto parts store under the name "belt dressing". Try to spray it on the belt and see what happens. It may be caused by misalignment of the belt and/or excessive slip, which would be calling to check belt tension. It could be a problem with alternator as well. Good luck finding the culprit.

Posted on Jul 21, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crank shaft sensor location on a 1996 ford taurus


on the 3.4 SHO the sensor is mounted in the front right side of the block
it reads off the gear behind the crankshaft pulley

on the 3.0 4v its similar to 3.4 but just mounted front left side

on the 3.0 2v its mounted against the front of the block reading off the crankshaft pulley

Aug 28, 2016 | 1996 Ford Taurus

1 Answer

Serpentine belt on 2006 Ford Taurus SEL squealing.


The belt has most likely moved either in or out on the bottom pulley. Check it first. I had the same problem it looked ok but was out one groove missleading designed pulley.

Oct 08, 2014 | 2006 Ford Taurus SEL

1 Answer

Squealing noise when i crank up and smell of something burning


then something is frozen with in the Serpentine Belt System, the Belt is squealing on the Frozen Pulley Raise the Hood Start car Look for the Pulley Not turning, there are about 5 different Pulleys, so it could be any one of them, starting With the Alternator Which is the Most common , then You may have 2 idler Pulleys, A Power Steering Pulley and A Water Pump Pulley, Can't tell You which one with out seeing it. Sorry

Jan 07, 2014 | 2002 Ford Crown Victoria

1 Answer

2001 escape squealing noise when engine is under presure


Use a mechanic's stethoscope to locate the culprit sqeal. Have a technician rev the engine, in order to produce the squeal. Lay the stethoscope tip utop the water pump, nearest the armature. Locate squeal in this fashion against the idler pulley(if applicable), the alternator, the air conditioner compressor, power steering pump (if applicable), the cam shafts (if applicable), and finally the crank. This will help isolate the location of the squeal.7_20_2012_9_07_34_pm.jpg

Jul 20, 2012 | 2001 Ford Escape

2 Answers

2002 Ford Mustang pulley squealing


Replace the crank pulley before it costs you an arm and a leg. It has caused this problem. don-ohio

Mar 26, 2017 | Ford Cars & Trucks

1 Answer

My belt is squealing really bad on my 96 Ford Probe SE 2.0 liter, i replaced the power steering pump, the power steering belt and it is still squealing. Is it a pulley?


Often these vehicles have a spring loaded tensioner, which you would have released to replace the belt. When the spring in the tensioner gets weak, causes a squeak.

Oct 27, 2010 | 1996 Ford Probe

3 Answers

I have a 1996 jeep grand Cherokee. The belt does not stay line up on the pulleys. Make a squeling noise. I believe it might be some bearing. I do I diagnose? What causes that


You will need to remove the belt and check each pulley and idlerfor play/ slop
My best answer is you will find an idler pulley that is shot

Mar 26, 2010 | 1996 Jeep Grand Cherokee

1 Answer

I get a loud squeal from the fan area only when


It could be a pulley. Best way to tell is to remove the belt and turn each pulley one at a time and see if you can either feel one not turning freely or try and duplicate the squeal. Keep in mind there is no load on the pulley without the belt on it so it might not be as pronouce as it would be with the belt on.

Jan 30, 2010 | 1996 Ford Crown Victoria

1 Answer

1996 ford escort


Only thing to know really is when you're retensioning the new belt is adjust the tensioner so you have about an inch of movement on the longest run between pulleys. Any tighter and you put too much strain on the bearings any looser it will squeal. If it does squeal just tension it a little more til it stops. Might need tensioning again after a few miles because it will stretch a bit.

Sep 05, 2009 | 1996 Ford Escort 4 Door

1 Answer

When I crank my van it makes a squealing sound and it shuts off. The engine light is on.


Sounds like you may have a pulley that has locked up on you. Have someone crank the engine while you carefully observe the pulleys and belts.

Apr 24, 2009 | 1999 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...