Question about 1993 Geo Metro

Open Question

93 geo metro Heater Control Valve location

Heater control valve

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimmymac725
  • 34 Answers

SOURCE: heater problems

I believe you have one of two problems either your heater core is plugged up and not allowing enough flow or the temperature blend door located under the dash is not moving.The heater core is easy to check,A quick check of the heater core is with the engine running and with the blower motor off or on low carefully chck to see if both heater hoses are equally hot if not remove them from the heater core and use a garden hose to backflush it the blend door can be more of a hassle as it can be operated by a motor or vacuum servo and even a simple cable these also have been known to break but with the blower on high change the temp control from cold to hot and see if you can hear a change in the sound of the blower and sometimes you can hear the door shut it more than likely the door is ok but you will need to check it and see.
Good Luck
Jim

Posted on Oct 07, 2008

  • 9 Answers

SOURCE: 1990 geo Prizm fuse location for the heater blower

the heater blower motor is run through two fuses. the gauge fuse in fuse block 1 and the ac fuse in fuse block 4.

Posted on Oct 07, 2008

jmassengill
  • 345 Answers

SOURCE: 93 Geo Metro

As long as they are the same type of engine ( I believe they should both be 1.0L 3 cyl engines). Most parts for the Geo Metro from 1992 to 1994 interchange with out a problem.

Posted on Nov 10, 2008

  • 1 Answer

SOURCE: blower motor location 1990 geo prizm

In my 1992 it is underneath the dash on the passenger's side, but you have to take the whole front panel including the glove box off to access it. When that is done there is a rectangular housing and a more circular housing. On the bottom of the circular housing there are three screws that hold the blower motor up. Remove the screws and it will drop right out.

Posted on Dec 22, 2008

  • 398 Answers

SOURCE: egr valve location

The EGR Valve Location is typically housed on the intake manifold this schematic may help you
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008822d

Posted on Mar 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the heater control valve located on my 1995 ChevyK1500


it is connected in the heater hose line, normally closer to firewall above exhaust manifold, there will also be a plastic vacuum line running to it.
links below will show, press the helpful button

96 Chevy Tahoe Heater Control Valve

8 Steps to Fix Your Automotive Heater Like Pro Pictures

96 K1500 Mystery Vacuum Line

Jan 26, 2016 | Cars & Trucks

1 Answer

Heater valve location


It's a vacuum line to control the valve? It will connect there at valve and run into and under the dash to the back of the heater control panel. All the vacuum control hoses for the heat and AC are in a pod that connects to the back of the heater controls. A vacuum line from the engine is also there, the pod will send the vacuum signal out to various doors on the heater/AC case, as the controls demand. One also goes to the heater control valve.

Sep 09, 2013 | Cadillac Catera Cars & Trucks

2 Answers

My 93 Geo doesn't shift properly


my guess is a bad governor.
bad throttle valve, on rear of tranny, either the cable one, or vacuum one.
the tests are all in the FSM and online at alldata.com, for $15

Jul 15, 2013 | 1993 Geo Metro

1 Answer

1998 mercury grand marquis heater doesnt work only cold air comes out the air cond works fine the enginecoolant is new, the engine doesnt overheat.


Either your heater control valve is not properly operating or your heater core is clogged. Locate the heater control valve under the hood, should be close to firewall on heater hose, have someone adjust temperature from hot to cold and see if you can see the heater control valve operating if so replace the heater core, if its not doing anything replace it(heater control valve).

Feb 19, 2011 | 1998 Mercury Grand Marquis

1 Answer

How do i replace a heater control valve on a 2001 sierra 1500 pick up


your heater control valve should be located on one of your heater hoses coming from the heater core. usually they are located close to the firewall and will have some type of control cable attached to it . Simply unhook the two hose clamps to remove and replace the valve .

Nov 18, 2010 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

1996 crown victoria has no heat


the temp blend door may not be rotating from the a/c evaporator to the heater core opening.

Could be the motor on the blend door or the temp control knob.

Do you have manual a/c or electronic temp control?

If it's the a/c door electronic actuator motor, it's on top of the plenum. Have to remove the instrument panel for access.

Hope it's the temp knob on the control head.

top one is the circuit you are looking at
68ae61d.gif

Apr 23, 2009 | 1996 Ford Crown Victoria

1 Answer

1995 Nissan Altima Heater contorl valve location


HELLO THE HEATER CONTROL VALVE IS LOCATED AT THE REAR CENTER OF THE ENGINE COMPARTMENT BY THE FIREWALL

Jan 09, 2009 | 1995 Nissan Altima

1 Answer

1995 geo metro blower moter speed resister


before you start you have to disconnect negative battery terminal. Remove glovebox.Remove harness connectors from ECM (electronic control module). To access blower motor resistor, remove ECM and disconnect blower resistor (remove screw and resistor mounted on heater case. To install reverse removal procedure.
Hope it helps

Dec 09, 2008 | 1995 Geo Metro

2 Answers

Part for heater control valve???


It is most likely a dealer item only, go to the dealer, they will help you ID and get the right part.

Sep 10, 2008 | 1995 Jeep Cherokee

Not finding what you are looking for?
1993 Geo Metro Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...