Question about 2002 GMC Sierra 2500HD

Open Question

Duramax wire on top of fuel filter assembly - 2002 GMC Sierra 2500HD

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 136 Answers

SOURCE: Do I need to bleed the fuel when I change out the

if its like my ford it'll have a bleeder valve by the fuel filter hope it does otherwise run the fuel line you'll find it

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 duramax lbz missing bad smokes black when aselerate chek fuel filter is half way full


no fuel filter should be full, replace fuel and air filter then try it again

Oct 31, 2015 | Cars & Trucks

1 Answer

2005 Duramax stopped running.replaced fuel filter and sensor,no luck cam you help.


After replacing the fuel filter did you prime the system? There should be a small circular pump on top of the filter assembly to prime it. I own a 2003 Duramax and it usually takes about 5 pumps / turn over / 5 more pumps / turn over / and 5 more and you should get it started. It will take longer if you didn't fill the fuel filter with diesel before installing it as well. Let me know. Thanks.

Sep 11, 2012 | Cars & Trucks

1 Answer

HOW TO CHANGE FUEL FILTER 2008 GMC DURAMAX DEISEL PICKUP


Disconnect the electrical connector for the "Water-In Fuel" sensor from the lower end of the filter housing. Then the filter assembly simply unscrews like an oil filter.After the fuel filter is off, you must unscrew the sensor from the lower end of the old filter and transfer it to the new filter. Then screw the new filter into place. There is a screw on the top of the filter housing to bleed the air from the fuel filter assembly. Loosen or remove the screw and pump the hand pum on top of the filter housing until fuel comes out the bleeder. Then tighten the bleeder and start the engine. If you did everything correctly, it should start right up and continue running. If it starts the dies in a couple of seconds, then you must perform the bleeding process again. (SEE PICTURES BELOW)

Hint: Sometimes it is much easier to get to the filter through the right wheel housing. It may be easier to support the vehicle and remove the right front tire to get to it.


11_16_2011_12_14_23_am.jpg

11_16_2011_12_14_45_am.jpg

11_16_2011_12_15_10_am.gif

Nov 15, 2011 | 1998 GMC Sierra

2 Answers

2002 chevy 6.6 duramax wont start even in warm weather or after motor is warm..... only starts with starting fluid. codes are p0335/p0193/poo87/p0090


The Duramax fuel filter assembly is bad about sucking air. Replace the fuel filter assembly. It comes with a new fuel filter.
I need some good feedback.

Oct 09, 2011 | 2002 Chevrolet Silverado 2500HD

1 Answer

Where is the Engine Fuel Temp Sensor "A" Circut High Input, on a 2001 GMC 3500 Duramax?


FUEL TANK PRESSURE SENSOR LOCATED ON TOP OF FUEL TANK WITH THE FUEL PUMP MODULE ASSEMBLY.

Sep 24, 2011 | GMC Sierra 3500HD Cars & Trucks

1 Answer

Do I need to bleed the fuel when I change out the


if its like my ford it'll have a bleeder valve by the fuel filter hope it does otherwise run the fuel line you'll find it

Nov 24, 2009 | 2007 GMC Savanna

1 Answer

2001, Duramax Deisel 6.6 won't "restart"


fuel pump is obviouslynot working !
check it & its wiring!!!!!

Jul 20, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

I changed fuel filter on 02 Duramax know it wont start


There is a priming pump on top of fuel filter assembly. Had to have somebody else pump it while turning the motor over, It fired right up. Was looking for a while for this pump, because it doesnt look like a pump, it is metal on top of fuel filter.

Mar 21, 2009 | 2002 GMC Sierra 2500HD

1 Answer

Chevrolet 2500 Not Running, May Be Fuel Filter Sensor


That red wire is only for the fuel heater.will not cause a no start.try pumping the primer pump on top of the fuel flter hsg. but first open the bleed screw,which is black plastic also located on the top.this will eliminate any trapped air that might have entered the fuel intake system.if the pump does not get firmer and harder to push, then you have a leak in the fuel supply lines or the ck valves in the fuel filter hsg or stuck open. Still no start have it scanned to ck fuel pressure while cranking.it should be close to 5000 lbs

May 14, 2008 | 2003 Chevrolet Suburban 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...