Question about Cars & Trucks

Open Question

Garnish tail light exalta STA broke - Cars & Trucks

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 181 Answers

SOURCE: My nissan exalta sta 2000 model, motor idles but dies as soon as you give it gas.. already change spark plugs, tune up, replace engine gasket and fuel filter..

I think you have a timing issue or fuel pressure issue. If you could tell me a little more about when this started, I will try to help

Posted on May 29, 2014

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Tahoe. Where is the auxiliary blower motor located?


It is located behind the right rear quarter panel , In the back right of the interior !
Remove the right rear quarter trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side in Interior Trim.
Removal Procedure
  1. Remove the rear seat. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
  2. Remove the Third Pillar trim panel. Refer to Third Pillar Trim Replacement .
  3. Remove the garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
  4. Remove the door sill plate. Refer to Liftgate Door Sill Plate Replacement .
  5. Remove the quarter panel trim screws.
A lot involved in this but not to difficult !
  1. Remove the rear door sill trim plate. Refer to Front Side Door Sill Plate Replacement or to Rear Side Door Sill Plate Replacement .
  2. Remove the lower rear seat belt cover and bolt.
  3. Remove the trim panel from the vehicle.
Remove the sill plate. Firmly pull the sill plate up and out from the retainers.
Remove the sill plate from the vehicle. Start from the front of the door sill. Use a flat-bladed tool in order to pry the door sill plate.
Rear Side Door Sill Trim Plate Replacement
Use a flat-bladed tool in order to pry the door sill plate. Remove the sill plate from the vehicle.
Body Rear Corner Garnish Molding Replacement
Remove the rear upper garnish molding. Refer to Rear Upper Garnish Molding Replacement .
Pull down on the upper corners of the garnish molding in order to disengage the retaining clips. Pull in order to disengage the remaining retaining clips. Remove the rear corner garnish molding from the vehicle. Inspect the rear corner garnish molding for broken or missing retaining clips. Replace the retaining clips as needed.
Good Luck ! Fun job !!!!!

Jun 07, 2015 | 2006 Chevrolet Tahoe

3 Answers

My nissan exalta sta 2000 model, motor idles but dies as soon as you give it gas.. already change spark plugs, tune up, replace engine gasket and fuel filter..


Has the car been running on empty recently? Running with low fuel can damage your fuel pump because on some cars the gasoline is the lube for the pump. a bad fuel pump could be the problem. Look up some YouTube videos on how to diagnose

May 25, 2014 | 2001 Nissan Sentra

1 Answer

High brake light


You will have to remove inner garnishing...To access the upper tail light...the rest of the wiring is fed in through the of the van...you will have to follow the wires...be patient....all the wires should be on the drivers side....

Nov 24, 2013 | 2008 Honda Odyssey EX-L

1 Answer

My tail light in my Chevy Tahoe is out and I need to replace it but lost my manual can someone tell me what I need to do.


From other owners experiencie:
- Ensure the headlamp switch is in the OFF position.
- Remove the upper garnish molding at the headliner.
- Remove the right and left side rear window garnish molding.
- Lower the rear of the headliner in order to access the electrical connector.
- Disconnect the electrical connector.
- Attach a short piece of wire to the high mounted stop lamp connector in order to assist the guiding of the harness through the body.
- Remove the high mounted stop lamp screws.
- Remove the high mounted stop lamp from the vehicle.

zjlimited_476.jpg
zjlimited_477.jpg
Hope helps.

Jan 14, 2011 | 2004 Chevrolet Tahoe

1 Answer

The plastic broke in the wing tail light on my trunk, how do i find the replacement part and replace it


Wing tail light? Depends , you can get it from the dealer or just Google what light you need, like 2000 Ford tail light? But I guess what year your truck is a secret.

Sep 02, 2010 | Ford Taurus Cars & Trucks

1 Answer

Steering problem


check the level of the power steering fluid.

Mar 03, 2010 | 2001 Nissan Sentra

1 Answer

Transmission problem


you might want to check the brake pads. it might be thin enough to make the wear indicator touch the rotor disc.

May 28, 2009 | 2001 Nissan Sentra

1 Answer

Rear wiper motor broke


Well you going to have to open the tailgate up and remove the inside cover that is attached to it. You will need a small flat head and a No. 2 star head screw driver and some gloves so that you don't cut your hands....

First where the handle is remove the caps on the handle and then remove the handle there may be a small pocket around the handle to remove it also with the screw driver....And then remove the garnish from around the tailgate by using the small flat head and your fingers to pry it off with....Remember just to take your time when doing this and wear some safety glasses so that nothing goes in your eyes.

Once you have removed the garnish you should see the wiper motor there should be three bolts that hold it in place and wire wire coupler that it hooked up to it. And before you undo the motor you will need to go on the outside of the tail gate you will need to remove the wiper arm off of the motor and then take the rest off after that.

May 12, 2009 | Honda CR-V Cars & Trucks

1 Answer

Tail light malfuction


check the brown wire on the tailight harness on the truck chances are it shorted and broke away from the assembly. the fuse is in the junction box under the hood.

Sep 02, 2008 | 1992 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...