Question about Cars & Trucks

Open Question

How do you remove the center console in a 2006 chevy malibu ltz v6 3.5 liter

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 521 Answers

SOURCE: my 2006 chevy cobalt 2.2 liter sputters

Fault with the IAC valve.there maybe a trouble code associated with it also./ Go to your nearby autozone or auto parts retailer and ask them to put a scanner to the car....make note of the codes if any are found. the IAC valve i usually locate don the throttle body and can be removed for inspection and sometimes cleaning using a good throttle body cleaner spray and a pipe cleaner brush.

Posted on Aug 04, 2009

Ad
  • 400 Answers

SOURCE: 2006 chevy malibu.... where is the egr valve

If it's a US car then there is not an egr on the 2.2L engine. I think some of the mexican and oversea's engines had them, but not here in the US.

Posted on Oct 21, 2009

  • 4044 Answers

SOURCE: how do i replace serpentine belt on a 2000 chevy

You shouldn't need to remove the engine support. I recommend you get a Haynes repair manual for your vehicle from Auto Zone or the local Auto Parts store. If you do have to remove the support it should be a simple procedure.

Posted on Nov 17, 2009

  • 3230 Answers

SOURCE: Change headlight on 2008 Chevy Malibu

Hi there,

Well first you can please follow the below steps -
1. Make sure the ignition key is in the off position and the headlight switch is off. Release the hood latch.
2. Open the hood and locate the top of the headlight assembly where you intend to change the headlight. If a plastic shroud is present, locate the center bolt and remove it with a ratchet and a socket. Lift the shroud out of the way to access the headlight assembly retaining brackets. Some later models may feature a snap-release shroud requiring no tools to remove.
3. Locate the brackets on the top rear of each side of the headlight assembly. Lift them all the way up to align the hole on the bottom of each bracket to the retaining tabs on the assembly.
4. Pull the assembly forward away from the Malibu, but be careful not to scratch the bumper. There are three guide pins that require unseating. The guide pins are what aim the headlights and it may take some wiggling to get the pins from their seats.
5. Support the assembly with one hand and then reach behind the unit with the other. The low beam bulb is on the outside, the high beam bulb is on the inside. You can also replace the parking light if desired. Locate the wire harness connection. Un-clip the wire harness from the back of the bulb socket. Remove the bulb by turning it counterclockwise 1/3 of a turn to align the release tabs of the ring and the assembly. Wiggle the bulb out of the assembly.
6. Place the latex gloves on your hands before opening the package of the replacement bulb. Oil in our skin can damage the glass bulbs of halogen headlights.
7. Carefully insert the new bulb into the ring and then align the tabs of the ring to the tabs of the headlight assembly. Push inward and then twist clockwise 1/3 of a turn to lock the bulb in place. Reattach the wire harness. Rest the headlight assembly inside its cavity and test the operation of the headlight before securing the headlight assembly in place. Be sure to turn the lights and ignition back off.
8. Align the three guide pins to their seats and push the assembly back into them gently until they snap into place. Replace the retaining brackets by pushing them downward to lock into place. Replace shroud, if applicable. Remove the tools and old bulb and close the hood. Post comments for further help or information......

Good Luck!!

Posted on Mar 27, 2010

  • 60 Answers

SOURCE: What are the step by step instructions to change

Find the oil drain plug, remove, drain the oil into a pan, reinstall the drain plug a tighten, locate the oil filter and remove, check mounting surface to make sure the old gasket didn't stick. Coat the new filter gasket with oil and install hand tight. Refill the oil, make sure that you do not overfill. Start enigne for about a minute, shut off and double check the level, and that the filter and drain plug do not leak.
Some engines can be difficult, to identify the location of the drain plug and filter. There are thousands of configurations out there, If you are not familiar or can not locate the plug and filter, take the vehicle to a shop for service.

Posted on Apr 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cap to recharge the ac for my 2008 chevy Malibu LTZ 6 cylinder


First pop the engine cover off. You are looking for a small cap with an "L" on it. This stands for Low Pressure. Most of the time they are blue. Avoid the "H" (High Pressure). The lines are typically silver in color.

May 01, 2015 | 2008 Chevrolet Malibu LTZ

1 Answer

Where is the oil pump on 2007 Chevy Malibu Maxx LTZ


its on the bottom of the engine block, inside the oil pan

Mar 20, 2014 | 2007 Chevrolet Malibu Maxx LTZ Hatchback

1 Answer

2006 Chevy Malibu power mirror fuse


On the right front of the center console, remove the panel directly next to the floor. It is marked with a fuse symbol. It has a velcro pad behind the "O" marking near the front. Just pull on the end with the "O" marking. once the panel is removed, fuses are identified on the back. Power Mirror = 2a fuse in the front upper of the panel.

Jan 17, 2012 | 2006 Chevrolet Malibu

1 Answer

Where is the location of the PCV valve in a 3.5 liter 2006 Chevy Malibu Maxx?


Almost all PCV Valves, have been on one valve cover or the other, for
the last 50 years

They never need replacement.

Remove & clean, if you got nothing else to do

Sep 20, 2011 | 2006 Chevrolet Malibu Maxx

1 Answer

2007 malibu max rear door panel removal


how do i get the rear driver door panel off without distroying it???
2007 chevy malibu maxx 6cyl.
Stb723@gmail

Mar 23, 2010 | 2007 Chevrolet Malibu Maxx LTZ Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...