Question about 2005 Toyota Tacoma

Open Question

How to bleed brakes on a 2005 Toyota tacoma

What is the order for bleeding brakes

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: 2008 Toyota Tacoma Excessive brake pedal

Your dealer is not lying to you.
All of the Toyota product line with ABS has this phenomenon. What Toyota has done is incorporate "Brake Force Distribution" into the braking system. What that means is there is now a sensor on the brake pedal/brake rod, going to the master cylinder. The sensor measures how FAST you press on the brake pedal. This activates the ABS pump, and supplies more brake fluid, harder, to reduce the time needed, such as a "panic stop"; the pedal travel is much longer than you are used to, because of the way they have to measure the speed of the rod being depressed. In actuality, this system is much better than the old system, as it also prevents wheel drag. It just takes a while to get used to. Really, there is nothing to worry about, I explain this same thing to my customers every week.

I hope this helps you out.

Thanks for choosing FixYa for assistance.

Posted on Mar 05, 2009

  • 49 Answers

SOURCE: cant bleed out brakes

It takes time, do you know the sequence to bleed the brakes? Most cars r different. And you have to keep pouring brake fluid, That is a two person job. Make sure all lines r connected to MC and not leaking. After a while if nothing comes out MC could be diffective.

Posted on Jun 06, 2009

polarcycle
  • 1392 Answers

SOURCE: toyota yaris brakes how do you bleed the brakes on a toyota yaris

have someone pump the pedal and hold it, then you work from the right rear, left rear, right front, left front, while the person pumps and holds several times at each wheel.

Posted on Jun 10, 2009

mecanica03
  • 874 Answers

SOURCE: bleed brakes on 2003 toyota corolla

i try to help you, firts refill brake fluid container,open purge valve in one wheel front only,wait few minutes when drops fluid, close this valve and open other wheel, same procedure, finally repeat this in each 4 wheels

Posted on Jul 14, 2009

  • 102 Answers

SOURCE: put new brake shoes in 98 toyota starlet do i need

I am going to assume, that you are refering to the rear brakes.
There should be a small access hole in the backing plate for the adjustment .
By turning the star wheel inside of the drum, will either bring the shoes into contact with the drum ,or back them right-off,depending which side of the car you are working on. Good luck

Posted on Mar 06, 2010

Testimonial: "THAT WORKED BUT HOW MUTCH TO AJUST I AJUSTED TILL WHEEL MOVED FREELEY BUT FIRM AND HANDBRAKE STILL DOESENT FEEL RIGHT NEED TO PULL UP HARD."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the brake bleed sequence on a 2005 Toyota Tacoma


Standard is bleeding from the furthest wheel to the master cylinder. So, you first do the right rear wheel, then you do the driver side rear wheel, then move to the front passenger wheel and finally you do the front driver side.

Jun 17, 2017 | 2005 Toyota Tacoma

2 Answers

Iv got a '96 ford taurus gl. When bleeding the brakes is there a certain order they should be done in?


Passenger rear, driver rear, passenger front, driver front, hope this helps

May 07, 2016 | Ford Cars & Trucks

1 Answer

What's the brake bleeding order on a 1999 Toyota solar a


right rear, left rear, right front, left front.

Sep 05, 2015 | 1999 Toyota Camry Solara

1 Answer

How do i unlock my brakes on my 2003 Toyota Tacoma 4 cylinder 2 wheel drive manual transmission?


You could start with bleeding the brakes to get all the air out.
If that doesn't work, I would just install new brake pads and calipers.
For safety reasons.
Hope this helps.

Feb 27, 2015 | 2003 Toyota Tacoma

1 Answer

How to disable ABS brakes on a 2011 honda pilot?


Hello,
You DO NOT need to disable the ABS in order to bleed the brake fluid from the system. Almost all of the time you usually bleed the brakes with the engine off anyways to get a "Hard" pedal. Even if you were to do it with the engine running it would not affect the bleeding procedure except the pedal will never pump up to being "Hard" and will give a false reading of still being "Soft" or going to the floor when in fact it may or may not be already OK. This is not the fault of the ABS system, just the running motor.
Good Luck!
Rich Lilja

Apr 03, 2014 | Cars & Trucks

1 Answer

Bleed brakes for 2005 prius


release? explain what that means.
what parts were disconnected? MC, tell what you did.
brakes good, bleed, no bad
brakes bad, parts pulled, now bad bleed,???? just a clue.here.
if you open a fitting north of the ABS main unit, you will be in trouble.


did you read the FSM on PRIUS< if not why not>?
got ABS,? sure...
some cars with ABS, have very specail rules and steps for
bleeding ABS. , including factory scan tools that must modulate
the ABS solenoids to clear air !
RTM.
or alldata.com/
i bounce in and read now for you.
it says.
Bleeding the brakes requires the use of the Toyota Hand-Held tester, or other appropriate scan tool. Follow the operating procedures of the Toyota Hand-Held tester, or other appropriate scan tool when bleeding the hydraulic brake system.

Before fiddling any car with ABS, google your car
see what others did wrong.... save lots of grief.
and a tow to a shop.


Dec 22, 2013 | 2005 Toyota Prius

1 Answer

No fluid coming out of the front brake calibers when bleeding brakes


keep bleeding the brakes in the correct order.as air in the system.

Dec 16, 2013 | Cars & Trucks

1 Answer

What do the capped lines on the ehcu do................my brother in law(so called mech.) told me that they were buttons that you had to hold in while bleeding the unit but when my buddy and me went to do...


Bleeder screws , If you haven't replaced the unit you don't need to do anything with them . Don't need to have the vehicle running , just bleed the brakes normally . If you have replaced the Electro-Hydraulic Control Unit you need a factory scan tool to cycle the unit solenoids
Important:
• Use the two-person bleed procedure under the following conditions:
- Installing a new Electro-Hydraulic Control Unit (EHCU) or new Brake Pressure Modulator Valve (BPMV).
- Air is trapped in the valve body
• Do not drive the vehicle until the brake pedal feels firm.
• Do not reuse brake fluid that is used during bleeding.
• Use the vacuum, the pressure and the gravity bleeding procedures only for base brake bleeding.
Raise the vehicle in order to access the system bleed screws.
Bleed the system at the right rear wheel first.
Install a clear hose on the bleed screw.
Immerse the opposite end of the hose into a container partially filled with clean DOT 3 brake fluid.
Open the bleed screw 1/2 to one full turn.
Slowly depress the brake pedal. While the pedal is depressed to its full extent, tighten the bleed screw.
Release the brake pedal and wait 10-15 seconds for the master cylinder pistons to return to the home position.
Repeat the previous steps for the remaining wheels. The brake fluid which is present at each bleed screw should be clean and free of air.
This procedure may use more than a pint of fluid per wheel. Check the master cylinder fluid level every four to six strokes of the brake pedal in order to avoid running the system dry.
Press the brake pedal firmly and run the Scan Tool Automated Bleed Procedure. Release the brake pedal between each test.
Bleed all four wheels again using Steps 3-9. This will remove the remaining air from the brake system.
Evaluate the feel of the brake pedal before attempting to drive the vehicle.
Bleed the system as many times as necessary in order to obtain the appropriate feel of the pedal.

Apr 26, 2017 | 2000 Chevrolet Silverado 1500

1 Answer

How to change a clutch master cylinder on a 2006 toyota tacoma


remove line from the side of clutch master cylinder two bolts or nuts on firewall inside vehicle is a pin on the upper side of clutch remove and pull old unit out bench bleed new master by filling and pressing in on the piston of the master cylinder. if you dont have a hose fitting dont bench bleed bleed it in vehicle( this method takes longer) install back in vehicle and hook it all back up torque bolts to 25 ft lbs then bleed the slve cylinder from under vehicle near back of motor just like bleeding brakes pump up hold and release the line pressure by opening valve on slave cylinder.

Apr 06, 2013 | 2006 Toyota Tacoma

1 Answer

Bleeding the brakes on a 2008 toyota tacoma


u may need help on this ok u need some one to pump the brake hard and fast 10 or more times but first on ur brake callber there should be a bleeder that u can losein or tighin the size of soket u should need is a 3/8 ok have someone to pump them brakes 10 or more time then hold it in as u losein the bleeder the peddle should go to the floor they will need to hold that peddle in as u tighin the bleeder then pump the brakes repeat this 5 or more times then do the same on the other side remember to keep brake fluid in the mastercylender or ur defeting ur self

Jun 10, 2012 | Cars & Trucks

Not finding what you are looking for?
2005 Toyota Tacoma Logo

Related Topics:

558 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...