Question about Cars & Trucks

Open Question

Ford galaxy 2.3 timing marks

Will not star mead to check timing marks

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: Need timing marks for 2002 ford explorer 4.0




The Info I Have Is Extensive and Has Illistrations, I Need to Emali it to You As it is Very Large, This Is A Small Example Im @rejakwilson@aol.com

Special Tool(s)

  1. With the vehicle in neutral, position it on a hoist.
  2. Remove the intake manifold.
  3. Remove the fuel supply manifold.
  4. Remove the accessory drive belt.
  5. Remove the thermostat housing.
  6. Remove the roller followers.
  7. NOTE: You must retime the LH and RH camshafts when either camshaft is disturbed. Turn the crankshaft clockwise to position the number one cylinder at top dead center (TDC).
  8. NOTE: Late build pulley shown, early build pulley similar. NOTE: The special tool must be installed on the damper and should contact the engine block to position the engine at TDC.

Posted on Jul 24, 2009

Ad

SOURCE: Need timing marks for 2002 ford explorer 4.0

There are no marks on this one. There is a special tool set to align camshafts ($900). The best you can do is to bring #1 cyl to TDC compression with both cam(valve) covers off. #5 cyl should have lobes at equal opening, exhaust just closing and intake just opening.. #1 cyl cam lobes should each be diametrically opposed to the positions of #5. If cams need to be moved, there is no registration of gear onto cam. Just loosen bolt holding gear and move cam. Retighten bolt. Roll thru 2 crank revolutions and check cam timing again.Simple.

Posted on Jul 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced timing belt idler tensioner on 2008 ford ranger and is now noisier is this normal


you might not have the timing right, it takes 2 or 3 turns on engine by hand checking the timing marks and adjust. first time on the marks you rotate engine by lower crank bolt, check and adjust putting back to timing marks, then repeat till the engine is lined up.

May 28, 2017 | Ford Cars & Trucks

1 Answer

Same time don't won't star 1995 ford explored


You either know how to check that out or you
need a repair shop

No one can tell you what is wrong,only testing
will do that

Worn out Starter Solenoid
Starter
Cables Loose
Battery Failing

You gave us nothing to go by,you
realize that

Sep 12, 2012 | 1995 Ford Explorer

1 Answer

How do you line up the timing gear in a 98 ford escort?


Hi.
Rotate the engine until the Timing mark on the Crankshaft pulley, is in line with the Timing mark on the Bottom casing.
Rotate the camshaft pulley until that Timing mark is in line with the Mark on the Camshaft bearing casting.
Install the timing Belt from the RH side, with no looseness in the Straight line tension, depress the Tensioner pulley, and feed the belt around the Water pump drive, and then the tensioner.
As you release the tension on the Tensioner pulley, ENSURE that neither of the Timing Pulleys MOVE.
Rotate the engine 2 times and check that the Timing marks at Top Dead Center are still ALIGNED.
If all is in good order, reinstall the Motor Mount and Belt covers and ancillaries.
Regards, DT

Mar 25, 2011 | 1998 Ford Escort

1 Answer

What are the timing marks 1987 ford ranger 2.3


star with your crank pulley, fuond a notch mark it (witeout woks fine) then botton of timign cover mark 0, bring them together and check your distribuitor rotor points to spark plug cable for piston #1 first front to back, if not match your timimg belt jumped.

Oct 02, 2010 | 1987 Ford Ranger

1 Answer

Timing belt timing marks, 1997 ford escort where are they?


Ford Escort/Tracer 1991-1999 Repair Guide

REMOVAL & INSTALLATION 1.8L Engine

(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers.
  3. Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
  4. Remove the crankshaft pulley and hub.
  5. If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
  6. Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
  1. Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
  2. Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
  3. Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
  4. Install the timing belt.
  5. Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
  6. Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.

fbe49f2.jpg
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

5bb74d0.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

9cafc26.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

72dc9cd.jpg
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines

  1. Make sure the camshaft pulley marks are aligned with the seal plate marks.
If the timing marks are not aligned, remove the belt and repeat the procedure.


I hope help you with this; remember rated this help. Good luck.

Sep 11, 2009 | 1997 Ford Escort

2 Answers

Set timing 2001 ford escort zx2


Hi, this system does not have a distributor. The timing is computer controlled and is not adjustable. In fact the manufacturer recommends that you do not even check it. most all vehicles that are fairly new have the same thing. hope this helps.

Jul 07, 2009 | 2001 Ford Escort ZX2

1 Answer

Timing


There are two. One is at the very center top of the head. It is a little arrow. The other is to the right hand side. Also a little arrow type mark.The Crankshaft mark is on the gear and another arrow mark on the engine.

Jan 07, 2009 | 1989 Ford Festiva

1 Answer

Hi 1962 Ford Galaxie Convertible 390cid V8 Need the Left side Exterior Chrome Strips(2)narrow and wide. How to locate the part on the internet? Thanks kondean@yahoo.ca PS: Galaxie not listed below....used...


Check with Dearborn Classics. They're out of Bend, Ore. Google 62 Ford Galaxie and check the related links. Dearborn Classics deals with Ford parts and are very good. They have alot of information on the early iron Ford parts.

Jul 15, 2008 | Ford F Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...