Question about Honda Civic

Open Question

2002 honda civic dx 1.7 liter p0122 tps senor low voltage

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

blueextc3221
  • 15935 Answers

SOURCE: How to change upper control arm on 1996 Honda Civic DX ?

UPPER CONTROL ARM:

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.

  1. Raise and support the vehicle safely.
  2. Remove the front wheels. Support the lower control arm assembly with a floor jack.
  3. Separate the upper ball joint from the steering knuckle using a ball joint separator tool.
  4. Remove the self-locking nuts from the upper arm anchor bolts. Remove the upper arm from the vehicle.

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.
To install:
Use new self-locking nuts when installing the upper arm and strut.
  1. Install the upper control arm assembly into the strut tower.
  2. Connect the upper ball joint.
  3. Install the front wheels and lower the vehicle.
  4. With all four of the vehicle's wheels on the ground, torque the upper control arm nuts to 47 ft. lbs. (65 Nm). Torque the castle nut to 32 ft. lbs. (44 Nm); then, only tighten it enough to install a new cotter pin.
  5. Tighten the wheel nuts to 80 ft. lbs. (110 Nm).
  6. Check and adjust the vehicle's front end alignment.
The bushings on the front lower control arms are replaceable on most models.
This procedure requires the use of a press and may be above the skill range of the average driveway enthusiast. It is recommended that this procedure be done by a qualified machine shop if you are not skilled in the proper use of a press.
  1. Remove the lower control arm that is in need of new bushings.
It is recommended that both the left and right lower control arm bushings be replaced at the same time. The vehicles handling may become unstable if there are new bushings on one side of the car and worn ones on the other.
  1. Set up the control arm in a press.
  2. Using a impact socket of the correct length and size, press out the old bushing.
  3. Install the new bushing by slowly using the press to push it into the control arm.
  4. WARNINGExcessive force could cause the bushing to bend or tear so be careful.
  5. Once the bushing is properly seated in the control arm, remove the arm from the press and install it on the vehicle.

Posted on Apr 05, 2009

  • 3 Answers

SOURCE: 2004 Honda Civic -Code P0122 Throttle Position Sensor Voltage Low

yes, this is the case of a failed throttle body, in which case it needs replaced, the car is getting too much fuel causing the high idle. this needs replaced asap. you could proably find a small independant honda shop that could do the work for less.

Posted on May 12, 2009

Karthik316
  • 187 Answers

SOURCE: 2002 honda civic wiring diagram

Hi,
http://www.installdr.com/Harnesses/HA-Wiring.pdf
pls rate my suggestion,,,,,

Posted on Jun 24, 2009

MNfisherman
  • 11896 Answers

SOURCE: how to remove transmission on 97 honda civic dx

remove crossmember, axles, cables, tranny mount bolts (3), tranny to engine of course bolts

Go to autozone.com and register for full free online repair manual

Posted on Sep 11, 2009

HondaCRX
  • 252 Answers

SOURCE: 1991 honda civic fuel pump replacement

You will need to remove the back seats and you will see the fuel pump in between the back seats and trunk. Run the car, remove the fuel pump fuse to relieve the pressure and then the car will die. Remove the pipes to the fuel pump, replace it and refit the pipes. Pump the gas pedal a few times and start it up (remember the fuse!)

If it is inside the tank (the fuel pump), then you will see the tank is held on by straps. Take them off, have ajack under it and remove the filler neck and screws holding it to the car. Remove the tank, undo the central bit where wires and pipes come out and slide the fuel pump out, replace what you have just done and refit.

Hope this helps, please vote :)

Posted on Jul 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello dennis i replaced my tps on my sonata but still get p0122


A P0122 code means that the the car's computer has detected that the TPS (throttle position sensor) is reporting too low a voltage. On some vehicles that lower limit is 0.17 - 0.20 volts (V).
Did you adjust it when you installed it? If the signal value is less than .17V then the PCM sets this code. Could be an open or a short to ground in the signal circuit. Or you may have lost the 5Volt reference voltage.
Symptoms may include:
  • Rough or low idle
  • Stalling
  • Surging
  • No/little acceleration
  • other symptoms may also be present
A code P0122 may mean that one or more of the following has happened:
  • TPS not mounted securely
  • TPS circuit short to ground or another wire
  • Faulty TPS
  • Damaged computer (PCM)
Some recommended troubleshooting and repair steps are:
  • Carefully check the throttle position sensor (TPS), wiring connector, and wiring for breaks, etc. Repair or replace as necessary
  • Check the voltage at the TPS (refer to a service manual for your vehicle for specific information). If the voltage is too low that is indicative of a problem. Replace if necessary.
  • If recently replaced the TPS may need to be adjusted. On some vehicles the installation instructions call for the TPS to be properly aligned or adjusted, consult a repair manualmag-glass_10x10.gif for specifics.
  • If there are no symptoms at all, the problem may be intermittent and clearing the code may resolve the issue temporarily. If this is the case then you should definitely check the wiring to be sure it's not rubbing on anything, grounding, etc. The code may come back.

Oct 01, 2011 | Cars & Trucks

1 Answer

P0122 error code on a 1999 oldsmobile 88


P0122 Code - Throttle Position Sensor/Switch A Circuit Low Input
A P0122 code means that the the car's computer has detected that the TPS (throttle position sensor) is reporting too low a voltage. On some vehicles that lower limit is 0.17 - 0.20 volts (V).

Did you adjust it when you installed it? If the signal value is less than .17V then the PCM sets this code. Could be an open or a short to ground in the signal circuit. Or you may have lost the 5Volt reference voltage.

Symptoms may include:
Rough or low idle
Stalling
Surging
No/little acceleration
other symptoms may also be present

Causes: A code P0122 may mean that one or more of the following has happened:
TPS not mounted securely
TPS circuit short to ground or another wire
Faulty TPS
Damaged computer (PCM)

Possible Solutions: Some recommended troubleshooting and repair steps are:
Carefully check the throttle position sensor (TPS), wiring connector, and wiring for breaks, etc. Repair or replace as necessary
Check the voltage at the TPS (refer to a service manual for your vehicle for specific information). If the voltage is too low that is indicative of a problem. Replace if necessary.
If recently replaced the TPS may need to be adjusted. On some vehicles the installation instructions call for the TPS to be properly aligned or adjusted, consult a repair manual for specifics.
If there are no symptoms at all, the problem may be intermittent and clearing the code may resolve the issue temporarily. If this is the case then you should definitely check the wiring to be sure it's not rubbing on anything, grounding, etc. The code may come back.


Test it and keep us updated.

Jun 12, 2011 | Oldsmobile 88 Cars & Trucks

1 Answer

2004 - JEEP LIBERTY SPORT 3.7/V6 ENGINE LIGHT ON !!! CODE #(P0122) What is it ? Can I fix it ? Dealership fix only ?


P0122 Code - Throttle Position Sensor/Switch A Circuit Low Input

A P0122 code means that the the car's computer has detected that the TPS (throttle position sensor) is reporting too low a voltage. On some vehicles that lower limit is 0.17 - 0.20 volts (V).

Did you adjust it when you installed it? If the signal value is less than .17V then the PCM sets this code. Could be an open or a short to ground in the signal circuit. Or you may have lost the 5Volt reference voltage.

Symptoms may include:
* Rough or low idle
* Stalling
* Surging
* No/little acceleration
* other symptoms may also be present

Causes: A code P0122 may mean that one or more of the following has happened:
* TPS not mounted securely
* TPS circuit short to ground or another wire
* Faulty TPS
* Damaged computer (PCM)

Possible Solutions: Some recommended troubleshooting and repair steps are:
* Carefully check the throttle position sensor (TPS), wiring connector, and wiring for breaks, etc. Repair or replace as necessary
* Check the voltage at the TPS (refer to a service manual for your vehicle for specific information). If the voltage is too low that is indicative of a problem. Replace if necessary.
* If recently replaced the TPS may need to be adjusted. On some vehicles the installation instructions call for the TPS to be properly aligned or adjusted, consult a repair manual for specifics.
* If there are no symptoms at all, the problem may be intermittent and clearing the code may resolve the issue temporarily. If this is the case then you should definitely check the wiring to be sure it's not rubbing on anything, grounding, etc. The code may come back.


Hope helps (remember to rate this answer).

Mar 01, 2011 | Jeep Liberty Cars & Trucks

2 Answers

Please can you give me the code of TPS of Chevrolet Epica 2004


There are 3 DTC codes related to the TPS....

1. P0121 - Throttle Position (TP) Sensor Performance

2. P0122 - Throttle Position (TP) Sensor Circuit Low Voltage

3. P0123 - Throttle Position (TP) Sensor Circuit High Voltage

If there is any further assistance, please let us know

Sep 27, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

What is Codes PO122 & PO303?


P0122 = TPS (throttle position sensor) voltage reports too low. This means that you could have a problem with the TPS, the wires to the TPS or the computer, if you have not replaced the TPS or do not want to do this work, I would take it in to a shop for this to be done. The TPS may require adjusting after replacement.
P0303= Cylinder Number 3 Missfire Detected, this means that the number 3 cylinder has miss fired, probably set this code as a result of the P0122 code. I would repair code P0122 and clear both codes. Hope this helps, let me know.

Aug 04, 2010 | Ford Ranger Cars & Trucks

2 Answers

Check engine light came on trouble shooting code is P 0122


Code P0122 is a TPS (Throttle Position Sensor) sensor out of range.

The operating range of the TPS is about .5 to 4.8 volts. .5 at idle 2.5 at half throttle and 4.8 at full throttle.

This can be checked easily with a scanner. But can be checked with a multi-meter.
P0122 Tjrottle Position Sensor low voltage

You can try replacing it for a start and see what happens
(location image)...

f1c255f.gif

Hope this help.

Mar 29, 2010 | 2005 Kia Sedona

1 Answer

2002 Interpid 2.7 L died on road now no start!


sounds like a bad ecm aka computer to me.have ecm checked

Aug 15, 2009 | 1999 Dodge Intrepid

2 Answers

2004 Honda Civic -Code P0122 Throttle Position Sensor Voltage Low


yes, this is the case of a failed throttle body, in which case it needs replaced, the car is getting too much fuel causing the high idle. this needs replaced asap. you could proably find a small independant honda shop that could do the work for less.

May 12, 2009 | 2004 Honda Civic

1 Answer

Throttle position sensor for honda civic 99model


what engine is in it, what model designation? (dx, ex, lx)

Oct 03, 2008 | 1998 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...