Question about Cars & Trucks

1 Answer

Engine light is on, oil light is on, hazor light keeps beeping. I have a SAAB 2002 93.

Just had 1200 done in work. Now this is happening. OME CODE P0116 they put a new water pump in, coolant and serpentine belt. said coolant system was leaking. now the car is worst,

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 271 Answers

An oil pressure warning light or low gauge reading means one of two things: either your engine has dangerously low oil pressure, or the oil pressure sending unit that triggers the warning light (or operates your gauge) has failed.


----------------------obd2express.co.uk

Posted on Nov 30, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Serpentine belt in a 1995 Mercury sable




I have the same car and last night my belt slipped off. The top small pulley backed it's self out. The problem is in most cars the pulleys are reverse threaded so this wont happen, in ours not so much. The pully spins loose with the turn of the belt so it has to be tightened way down. IT's a pain. Here is a diagram I found and You need a 15mm wrench, which doesn't just come in most sets. Good Luck

The book says "Using a 15 mm socket or wrench on bolt attaching drive belt tensioner pulley, rotate drive belt tensioner clockwise. Make sure spring keeper engages into slot." I would put a socket on the 15 mm pulley bolt and a long handle for leverage. Thats one tight spring.
62444297.gif 62444298.gif

Posted on Nov 06, 2008

  • 5 Answers

SOURCE: 1966 Ford Mustang overheating

try to run the water pump without hoses, and add water in the 'in' side, if is powers out the other side, then it's fine. how is your water/coolant mix?

Posted on Dec 01, 2008

08rtaylo
  • 3 Answers

SOURCE: 97 Cavalier engine coolant light.

have you changed the sensor on the coolant reservoir? try that.

Posted on Feb 18, 2009

csmock132
  • 4669 Answers

SOURCE: 99 cavalier temperature gauge won't work

Sounds like your cluster died, try getting one from a salvage yard.

Posted on Mar 02, 2009

  • 91 Answers

SOURCE: water pump leaked coolant into oil is motor done

It should be OK after a few oil changes. I would keep a close eye on the oil to make sure it isn't turning milky or foamy. If it starts knocking, you may have a more serious problem.

Posted on Apr 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2006 Saab 97x 4.2i, check engine light is on the the codes that came up are p0014, and p1400. Can anyone tell me the problems


Please follow the link for info you requested on P0014
http://www.autocodes.com/p0014_saab.html

P1400 Saab
When you check engine light came on code P1400 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However Saab manufacturer may have a different definition for the P1400 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.
Saab P1400 Possible Solution : The crankshaft sensor signals the fuel injection computer or the ignition control when the cylinders are firing. This causes the ignition coil to provide a spark and the injector to inject fuel into each cylinder at the right time.If either sensor isn't working correctly, the car will run rough and the engine will be less efficient. In later car models, the car's computer can usually keep the vehicle running, but the engine warning light on the dashboard goes on to warn the driver.

Nov 27, 2016 | Saab Cars & Trucks

1 Answer

Getting code P0520 engine speed sensor. How do you replace this. ABS light, brake light. check engine light on. Speedometer does not work


the engine speed sensor is located just above the oil pan at the rear of the engine. it is held in by one screw. For your abs issue see www.saabservices.com and look for abs light link. They can help you with those problems.

Mar 30, 2011 | 1999 Saab 9-5

1 Answer

How to clear service engine soon light on dash after an oil change was done ?


Switch ignition on
Press and hold clr button for 8/10 seconds
Service will appear in display after 2 beeps
Switch ignition off

May 11, 2010 | 1999 Saab 9-5

2 Answers

99 saab v6 oil light comes on and flickers at idle goeas away when you hit the gas. perfect oil level.


I would suggest replacing the oil sending unit,they will go bad,and cause this to happen,if this does not help,it can be the oil pump,or the main,and rod bearings wearing out.

Mar 02, 2010 | Saab 9 5 Cars & Trucks

1 Answer

Check engine & check gear box light on 1998 Saab 200S


not sure, run a code scanner on it and post the trouble code that would help to diagnose. Your local auto parts store can probably scan it for you.

Dec 19, 2009 | 2004 Saab 9-3

4 Answers

What oil should I use in my Saab 96 900?


factory recommends you use 10w-30 motor oil ,hope this is helpful.

Nov 27, 2009 | 1996 Saab 900

2 Answers

Oil pressure warning light flashe's on then goe's of


If oil & filter done/checked on a regular basis,and no new sounds or noises from engine, I would certainly lean toward new oil pressure switch. Probably does it more often when stopping maybe? If your very nervous about it, have a mechanic hook up his own good oil pressure gauge to engine in order to verify pressure is where it should be.

Mar 08, 2009 | Saab 9 5 Cars & Trucks

2 Answers

2001 Saab 95 engine light on


weird one this -- sounds like you spilt oil over some of the connections ??and they have run to ground thowing the check light on

Dec 07, 2008 | 2003 Saab 9-3

2 Answers

Oil Engine Light turned on and beeped after it reached 1200 rpm and then the clicking noise


have you done an oil change lately? If so did you doit yourself or was it done by a shop? I would check to see that the corret oil has been used fior your vehicle, I would also double check that the correct oil filter has been used. also on the open end of the oil filter that attaches to the car is a rubber " O " ring, I would remove the filter that is on there now and check to see that the O-ring from the old filter was not left behind.

Oct 16, 2008 | 2001 Volkswagen Beetle

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...